Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

LTS Josephson junction critical current uniformities for LSI applications

L.A. Abelson, K.P. Daly, N. Martinez, Andrew D. Smith

Published Jun 1, 1995• 19 citations
Publisher

Abstract

Manufacturing yields of large scale superconducting circuits depend strongly on the uniformity of junction critical currents. We report on junction manufacturing tolerances based on extensive measurements of Nb- and NbN-based junction arrays and individual junctions. Transient waveforms induced by switching of a single junction have sufficient amplitude to switch other junctions in a series array. We have measured the effect of sympathetic switching and developed damping structures to dissipate switching transients. Comparisons of critical current distributions measured on individual junctions with critical current distributions determined from series junction arrays are presented. In addition, the validity of using series arrays of large numbers of junctions to assess the critical current uniformity is discussed.>

DOI
10.1109/77.403154

Related papers

Niobium nitride Josephson junction process development

James M. Murduck, J. DiMond, C.Y. Dang +1 more

NbN/MgO/NbN tunnel junction fabrication has been developed using statistical experimental design for insertion into a Josephson LSI (large-scale integration) fabrication technology. Junction deposition conditions have been studied and correlated with structural characterization and junction I-V measurements. Josephson junctions with sum gaps as large as 5.0 mV and junction quality factor of 47 mV have been produced. Current density uniformity, a critical parameter in circuit design, has also been investigated. I/sub c/(O) uniformity at 4.2 K of a 4000 junction array was within sigma =3.1% and was +or-10% across 1 in/sup 2/. The utility of this junction process has been demonstrated by insertion into a standard circuit fabrication process that has produced logic circuit operation above 10 K.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•7 citations

Development of Self-Shunted Josephson Junctions for a Ten-Superconductor-Layer Fabrication Process: Nb/NbN x /Nb Junctions

Sergey K. Tolpygo, Ravi Rastogi, Terence J. Weir +2 more

To increase the integration scale of superconductor electronics, we are developing a new node, titled SFQ7ee, of the fabrication process at MIT Lincoln Laboratory. In comparison to the existing SFQ5ee node, we increased the number of fully planarized superconducting layers to ten and utilized NbN and NbN/Nb kinetic inductors to increase the possible inductor number density above a hundred million inductors per cm2. Increasing the Josephson junction number density to the same level requires implementing self-shunted high-JcJosephson junctions. We investigated the properties of Nb/NbNx/Nb trilayer junctions as a potential replacement of high-JcNb/Al-AlOx/Nb junctions, where NbNxis a disordered, overstoichiometric, nonsuperconducting nitride deposited by reactive sputtering. Dependences of theIcRnproduct and Josephson critical current density, Jc on the NbNx barrier thickness and temperature were studied in the thickness range from 5 nm to 20 nm. The fabricated junctions can be well described by the microscopic theory of SNS junctions, assuming no suppression of the energy gap in Nb electrodes near the NbNxinterfaces and a Cooper pair decay length in the NbNx barrier, ξnTcof about 2.3 nm. Current-voltage characteristics of the junctions are well described by the resistively and capacitively shunted junction (RCSJ) model without excess current. In the studied rangeJc2, the Nb/NbNx/Nb junctions have lower values of the specific resistanceRnA, lower IcRn products, and a stronger dependence of theIcRnon temperature than the self-shunted or critically damped externally shunted Nb/Al-AlOx/Nb junctions with the same critical current density; A is the junction area,Icthe junction critical current, and Rnthe effective shunting resistance.

arXiv:2312.13475•IEEE Transactions on Applied Superconductivity•Feb 9, 2024•14 citations

SNS junction on Nb-Ti base for microwave circuits

M. Schubert, Ludwig Fritzsch, G. Wende +1 more

Superconductor-normal metal-superconductor (SNS) junctions are well-suited for large-scale integrated superconducting circuits. Potential applications are programmable voltage standards, digital-to-analog converters and large-scale RSFQ circuits. The application of SNS junctions provides some advantages, e.g. a simplified fabrication technology and reduced parasitic inductances. But it requires a technological process with dimensions down to the submicrometer region to achieve sufficiently high characteristic voltages I/sub C/R/sub N/. In our process the normal metal interlayer is titanium. Therefore the sidewall insulation of the junctions can be made by anodization, as it is known from the Nb-Al technology. Nb-Ti-Nb Josephson junctions and junction arrays were fabricated down to the submicrometer range with I/sub C/R/sub N/ values up to 87 microvolt depending on the titanium thickness. Their measured critical currents have a small spread of about 10 percent. Shapiro steps are observed under the influence of microwave irradiation. For the application of such junctions in a programmable Josephson voltage standard a new type of microwave circuit using coplanar strips is proposed and successfully tested in 10 V SIS circuits.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•12 citations

Superconductor-normal-superconductor junctions for programmable voltage standards

S. P. Benz

Series arrays of Nb–PdAu–Nb Josephson junctions were fabricated with characteristics ideally suited for application in programmable voltage standards and D/A converters with fundamental accuracy. Large arrays of junctions with applied microwave power showed constant voltage steps with current amplitudes as large as 7 mA. A novel coplanar waveguide design enabled uniform microwave power coupling to a five-segment array of 8192 junctions, so each segment had constant voltage steps over the same bias range. The 8192-junction device generated 1.1 mA steps at 186 mV with 11 GHz power and a maximum constant voltage step of 260 mV at 15.34 GHz.

Applied Physics Letters•Oct 30, 1995•131 citations

Intrinsically shunted NbN/TaN/NbN Josephson junctions on Si substrates for large-scale integrated circuits applications

Kaixin Yan, Lu Zhang, Yulong Zhong +8 more

Abstract Superconducting circuits based on Josephson junctions have the potential to achieve high speed and ultra-low power consumption, but their integration is limited by the low controllability of Nb-based tunnel junction and the existence of shunt resistors. In this work, we report the fabrication of superconductor/normal metal/superconductor (SNS) Josephson junctions with high reproducibility on oxidized Si substrates. The junctions based on NbN/TaN/NbN trilayers measured at 4.2 K show excellent Josephson properties with a wide range of critical current ( I c ) from 227 to 2000 μ A. The variations of critical current density ( J c ) and characteristic voltage ( V c ) are respectively less than 7.1% and 7.5% in the 2 inch region. The standard deviation of I c is calculated to be less than 1.7% for Josephson arrays with the number of junctions up to 10 000 occupying an area of 0.34 mm 2 . The results provide a guarantee for the applications of NbN-SNS Josephson junctions in superconducting large-scale integrated circuits.

Superconductor Science and Technology•Feb 28, 2022•10 citations

SNS Josephson Junction Series Arrays for the Josephson Arbitrary Waveform Synthesizer

Oliver Kieler, J. Kohlmann, Ralf Behr +3 more

The Josephson arbitrary waveform synthesizer (JAWS) allows AC voltages to be generated with fundamental accuracy. Lumped arrays of superconductor/normal conductor/superconductor (SNS) Josephson junctions were developed and investigated for this application. Combining electron-beam lithography and chemical-mechanical polishing, series arrays of sub-micrometer SNS junctions consisting of Nb/HfTi/Nb were fabricated. The junction size varied from 0.04 mum2to 4 mum2in series arrays up to 2560 junctions in different microwave designs. Stable Shapiro steps are generated in a frequency range from 5 GHz to 20 GHz using continuous microwave irradiation. Using a simple pulse pattern at different pulse repetition frequencies, the arrays show current-voltage characteristics with flat Shapiro steps. Sinusoidal AC voltages were synthesized using a commercial pulse pattern generator. Peak-to-zero voltages of some mV for frequencies below 1 kHz were achieved. Higher harmonics were measured to be more than 80 dB below the fundamental tone. The behavior of the arrays was investigated in more detail by measuring the amplitude-frequency spectra.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•23 citations
Manufacturing yields of large scale superconducting circuits depend strongly on the uniformity of junction critical currents. We report on junction manufacturing tolerances based on extensive measurements of Nb- and NbN-based junction arrays and individual junctions. Transient waveforms induced by switching of a single junction have sufficient amplitude to switch other junctions in a series array. We have measured the effect of sympathetic switching and developed damping structures to dissipate switching transients. Comparisons of critical current distributions measured on individual junctions with critical current distributions determined from series junction arrays are presented. In addition, the validity of using series arrays of large numbers of junctions to assess the critical current uniformity is discussed.>
NbN/MgO/NbN tunnel junction fabrication has been developed using statistical experimental design for insertion into a Josephson LSI (large-scale integration) fabrication technology. Junction deposition conditions have been studied and correlated with structural characterization and junction I-V measurements. Josephson junctions with sum gaps as large as 5.0 mV and junction quality factor of 47 mV have been produced. Current density uniformity, a critical parameter in circuit design, has also been investigated. I/sub c/(O) uniformity at 4.2 K of a 4000 junction array was within sigma =3.1% and was +or-10% across 1 in/sup 2/. The utility of this junction process has been demonstrated by insertion into a standard circuit fabrication process that has produced logic circuit operation above 10 K.>
To increase the integration scale of superconductor electronics, we are developing a new node, titled SFQ7ee, of the fabrication process at MIT Lincoln Laboratory. In comparison to the existing SFQ5ee node, we increased the number of fully planarized superconducting layers to ten and utilized NbN and NbN/Nb kinetic inductors to increase the possible inductor number density above a hundred million inductors per cm2. Increasing the Josephson junction number density to the same level requires implementing self-shunted high-JcJosephson junctions. We investigated the properties of Nb/NbNx/Nb trilayer junctions as a potential replacement of high-JcNb/Al-AlOx/Nb junctions, where NbNxis a disordered, overstoichiometric, nonsuperconducting nitride deposited by reactive sputtering. Dependences of theIcRnproduct and Josephson critical current density, Jc on the NbNx barrier thickness and temperature were studied in the thickness range from 5 nm to 20 nm. The fabricated junctions can be well described by the microscopic theory of SNS junctions, assuming no suppression of the energy gap in Nb electrodes near the NbNxinterfaces and a Cooper pair decay length in the NbNx barrier, ξnTcof about 2.3 nm. Current-voltage characteristics of the junctions are well described by the resistively and capacitively shunted junction (RCSJ) model without excess current. In the studied rangeJc2, the Nb/NbNx/Nb junctions have lower values of the specific resistanceRnA, lower IcRn products, and a stronger dependence of theIcRnon temperature than the self-shunted or critically damped externally shunted Nb/Al-AlOx/Nb junctions with the same critical current density; A is the junction area,Icthe junction critical current, and Rnthe effective shunting resistance.
Superconductor-normal metal-superconductor (SNS) junctions are well-suited for large-scale integrated superconducting circuits. Potential applications are programmable voltage standards, digital-to-analog converters and large-scale RSFQ circuits. The application of SNS junctions provides some advantages, e.g. a simplified fabrication technology and reduced parasitic inductances. But it requires a technological process with dimensions down to the submicrometer region to achieve sufficiently high characteristic voltages I/sub C/R/sub N/. In our process the normal metal interlayer is titanium. Therefore the sidewall insulation of the junctions can be made by anodization, as it is known from the Nb-Al technology. Nb-Ti-Nb Josephson junctions and junction arrays were fabricated down to the submicrometer range with I/sub C/R/sub N/ values up to 87 microvolt depending on the titanium thickness. Their measured critical currents have a small spread of about 10 percent. Shapiro steps are observed under the influence of microwave irradiation. For the application of such junctions in a programmable Josephson voltage standard a new type of microwave circuit using coplanar strips is proposed and successfully tested in 10 V SIS circuits.
Series arrays of Nb–PdAu–Nb Josephson junctions were fabricated with characteristics ideally suited for application in programmable voltage standards and D/A converters with fundamental accuracy. Large arrays of junctions with applied microwave power showed constant voltage steps with current amplitudes as large as 7 mA. A novel coplanar waveguide design enabled uniform microwave power coupling to a five-segment array of 8192 junctions, so each segment had constant voltage steps over the same bias range. The 8192-junction device generated 1.1 mA steps at 186 mV with 11 GHz power and a maximum constant voltage step of 260 mV at 15.34 GHz.
Abstract Superconducting circuits based on Josephson junctions have the potential to achieve high speed and ultra-low power consumption, but their integration is limited by the low controllability of Nb-based tunnel junction and the existence of shunt resistors. In this work, we report the fabrication of superconductor/normal metal/superconductor (SNS) Josephson junctions with high reproducibility on oxidized Si substrates. The junctions based on NbN/TaN/NbN trilayers measured at 4.2 K show excellent Josephson properties with a wide range of critical current ( I c ) from 227 to 2000 μ A. The variations of critical current density ( J c ) and characteristic voltage ( V c ) are respectively less than 7.1% and 7.5% in the 2 inch region. The standard deviation of I c is calculated to be less than 1.7% for Josephson arrays with the number of junctions up to 10 000 occupying an area of 0.34 mm 2 . The results provide a guarantee for the applications of NbN-SNS Josephson junctions in superconducting large-scale integrated circuits.
The Josephson arbitrary waveform synthesizer (JAWS) allows AC voltages to be generated with fundamental accuracy. Lumped arrays of superconductor/normal conductor/superconductor (SNS) Josephson junctions were developed and investigated for this application. Combining electron-beam lithography and chemical-mechanical polishing, series arrays of sub-micrometer SNS junctions consisting of Nb/HfTi/Nb were fabricated. The junction size varied from 0.04 mum2to 4 mum2in series arrays up to 2560 junctions in different microwave designs. Stable Shapiro steps are generated in a frequency range from 5 GHz to 20 GHz using continuous microwave irradiation. Using a simple pulse pattern at different pulse repetition frequencies, the arrays show current-voltage characteristics with flat Shapiro steps. Sinusoidal AC voltages were synthesized using a commercial pulse pattern generator. Peak-to-zero voltages of some mV for frequencies below 1 kHz were achieved. Higher harmonics were measured to be more than 80 dB below the fundamental tone. The behavior of the arrays was investigated in more detail by measuring the amplitude-frequency spectra.