Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

9 K operation of RSFQ logic cells fabricated by NbN integrated circuit technology

Hirotaka Terai, Z. Wang

Published Mar 1, 2001• 16 citations
Publisher

Abstract

We report on the fabrication and the operation of all-NbN rapid single flux quantum (RSFQ) circuits. The NbN integrated circuit consists of NbN/AlN/NbN tunnel junctions, Mo resistors, sputtered SiO/sub 2/ insulating layers, and 400-nm-thick NbN ground plane and wiring layer. The circuits were fabricated with the minimum junction size of 2 /spl mu/m/spl times/2 /spl mu/m and the alignment margin of +/-0.5 /spl mu/m. We designed RSFQ logic cells under critical current density of 2.5 kA/cm/sup 2/, sheet resistance of 2 /spl Omega/ and sheet inductance of 1.4 pH. We experimentally investigated dc bias margin of the fabricated RSFQ cells at 9 K. We observed relatively large dc bias margin of more than +/-25% for a pulse splitter, a confluence buffer and an RS flip-flop, while the dc bias margin of a T flip-flop was less than +/-5%. We succeeded to demonstrate the operation of 16-bit concurrent flow shift register at 9 K.

DOI
10.1109/77.919398

Related papers

Design and Fabrication of All-NbN SFQ Circuits for SSPD Signal Processing

Kazumasa Makise, Hirotaka Terai, Shigehito Miki +2 more

We have developed an all-NbN integrated circuit technology for future integration of single flux quantum (SFQ) circuit with superconducting single-photon detector array. The all-NbN integrated circuits consist of epitaxial NbN/AlN/NbN tunnel junctions fabricated on single-crystal MgO substrates, Mo shunt resistors and 500-nm-thick NbN ground plane on the top. Critical current density and sheet resistance of the Mo resistor were set at 2.5 kA/cm2and 1.2 Ω, respectively. Current uniformity of the NbN/AlN/NbN tunnel junctions was measured to be σ = 3% for 3 μm × 3 μm junction size. The NbN-based SFQ logic cells were designed for and tested at 4.2 K. We actually measured circuit inductances of the fabricated SFQ cells. Circuit simulation revealed that the measured circuit inductances in the fabricated SFQ cells should allow operating margins of more than +/-20%.

IEEE Transactions on Applied Superconductivity•Dec 20, 2012•29 citations

Fabrication of NbN single flux quantum (SFQ) circuit and operating properties at 10 K

Hirotaka Terai, Zhen Wang

Abstract We fabricated a prototype of a single flux quantum (SFQ) logic circuit for operation near 10 K by using NbN, which has a critical temperature around 16 K. This circuit is fabricated on a 2‐inch silicon (Si) substrate based on the NbN/AlN/NbN tunnel junction having fluctuations in the critical current of ±5% or less from 976 Josephson junctions (JJ). The fabrication of a prototype circuit to generate, propagate, and detect SFQ pulses and the examination of its operation confirmed normal operation up to approximately 9.8 K, which is close to 10 K. In addition, at the operating temperature of 8.5 K, the operations of elementary cells such as a confluence buffer and a T flip‐flop were verified and were successful in the operation of the largest scale circuit, an 8‐bit shift register consisting of 105 JJ. © 2001 Scripta Technica, Electron Comm Jpn Pt 2, 84(10): 34–39, 2001

Electronics and Communications in Japan (Part II Electronics)•Sep 18, 2001•4 citations

A niobium nitride-based analog to digital converter using rapid single flux quantum logic operating at 9.5 K

Masoud Radparvar

An analog to digital converter (ADC) using the rapid single flux quantum (RSFQ) logic family implemented in niobium nitride (NbN) technology is described. The circuit was originally developed and demonstrated in niobium technology. An identical circuit was then laid out, fabricated and demonstrated in NbN technology. The chips were fabricated using an eight-layer NbN-based process with Josephson junction critical current density of 500 A/cm/sup 2/. In this paper, we report on the measurement results for a 6-bit flux quantizing ADC which exhibited proper operation and good DC bias margins. We also demonstrate results from an ADC chip operating up to 9.5 K.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1994•14 citations

RSFQ circuitry realized in a SINIS technology process

M. Khabipov, D Balashov, F.-I. Buchholz +2 more

We have developed integrated circuits in rapid single flux quantum (RSFQ) impulse logic based on intrinsically shunted tunnel junctions as the active circuit elements. The circuits have been fabricated using superconductor-insulator-normalconductor-insulator-superconductor (SINIS) multilayer technology. The paper presents experimental results of the operation of various RSFQ circuits realized in different designs and layouts. The circuits comprise dc/SFQ and SFQ/dc converters, Josephson transmission lines (JTLs), T-flipflops, and analog key components. Functionality has been proved; the circuits have been found to operate correctly in switching. The circuits investigated have a critical current density of j/sub C/=400 A/cm/sup 2/ and a characteristic voltage of V/sub C/=165 /spl mu/V, the area of the smallest junction is A=24 /spl mu/m/sup 2/. The junctions exhibit nearly hysteresis-free current-voltage characteristics (hysteresis: less than 7%), the intra-wafer parameter spread for j/sub C/ is below /spl plusmn/8%. The margins of the bias current I/sub b/ of the circuits have been experimentally determined and found to be larger than /spl plusmn/24%. At preset, constant values of I/sub b/, the range of a separate bias current I/sub bsw/ fed to a switching stage integrated between two segments of JTL's is fully covered by the operation margins which are larger than /spl plusmn/56%.

IEEE Transactions on Applied Superconductivity•Jan 1, 1999•15 citations

Experimental realization of a resistive single flux quantum logic circuit

V. P. Koshelets, K. K. Likharev, V. V. Migulin +5 more

An integrated circuit including all basic components of the recently suggested Resistive Single Flux Quantum (RSFQ) logic family has been designed, fabricated and tested successfully. The circuit includes a generator of periodic SFQ pulses, four buffer/amplifier stages for splitting, channeling and regeneration of the pulses, a detector/load stage, and universal RSFQ logic gate (here performing the NOT function). The 10μm design rule circuit employs 13 active Nb - Al2O3- Nb Josephson junctions with the critical current density ∼ 0.5 kA/cm2. externally shunted by Mo resistors with R 1 Ohm. The shunting provided critical damping of the junctions (\beta_{c}\lsim 1) and reasonable (\sim 500 \muV) IcR product. The circuit operation has been tested by measurement of dc voltages\bar{V}_{i}across various Josephson junctions as functions of the dc current through the pulse generator. Correct and stable operation of the circuit for the clock frequencies from 0 to ∼30 GHz has been demonstrated.

IEEE Transactions on Magnetics•Mar 1, 1987•37 citations

High-frequency performance of RSFQ circuits realized in SINIS technology

M. Khabipov, D Balashov, F.-I. Buchholz +1 more

The paper presents the determination of the high-frequency performance of Rapid Single Flux Quantum (RSFQ) circuits fabricated in superconductor-insulator-normal metal-insulator-superconductor (SINIS) technology. Circuits of different designs have been realized and were experimentally investigated, including specially designed T flip-flop (TFF) structures and circuits consisting of a switch terminated in Josephson transmission lines. For TFF circuits, the operational functionality was investigated in the frequency range from dc up to nearly 200 GHz. Two frequency domains were found. In the first domain, ranging up to frequencies of 80 GHz (f/sub C//spl cong/Y/sub C///spl Phi//sub 0/), correct digital operation of the device was ascertained. Beyond this range a second domain was found, ranging to nearly 200 GHz, for which quasi-analog frequency dividing is assumed. The bias current margins are /spl plusmn/30% at 40 GHz and /spl plusmn/15% between 130 GHz and 200 GHz. For circuits consisting of a switch, the operational functionality was proved in the frequency range from dc up to 50 GHz, with bias current margins of more than /spl plusmn/20%. The critical current density of the circuits is j/sub C//spl cong/750 A/cm/sup 2/. The smallest junction area is about A=12 /spl mu/m/sup 2/, and the characteristic voltage is V/sub C/=170 /spl mu/V.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•7 citations
We report on the fabrication and the operation of all-NbN rapid single flux quantum (RSFQ) circuits. The NbN integrated circuit consists of NbN/AlN/NbN tunnel junctions, Mo resistors, sputtered SiO/sub 2/ insulating layers, and 400-nm-thick NbN ground plane and wiring layer. The circuits were fabricated with the minimum junction size of 2 /spl mu/m/spl times/2 /spl mu/m and the alignment margin of +/-0.5 /spl mu/m. We designed RSFQ logic cells under critical current density of 2.5 kA/cm/sup 2/, sheet resistance of 2 /spl Omega/ and sheet inductance of 1.4 pH. We experimentally investigated dc bias margin of the fabricated RSFQ cells at 9 K. We observed relatively large dc bias margin of more than +/-25% for a pulse splitter, a confluence buffer and an RS flip-flop, while the dc bias margin of a T flip-flop was less than +/-5%. We succeeded to demonstrate the operation of 16-bit concurrent flow shift register at 9 K.
We have developed an all-NbN integrated circuit technology for future integration of single flux quantum (SFQ) circuit with superconducting single-photon detector array. The all-NbN integrated circuits consist of epitaxial NbN/AlN/NbN tunnel junctions fabricated on single-crystal MgO substrates, Mo shunt resistors and 500-nm-thick NbN ground plane on the top. Critical current density and sheet resistance of the Mo resistor were set at 2.5 kA/cm2and 1.2 Ω, respectively. Current uniformity of the NbN/AlN/NbN tunnel junctions was measured to be σ = 3% for 3 μm × 3 μm junction size. The NbN-based SFQ logic cells were designed for and tested at 4.2 K. We actually measured circuit inductances of the fabricated SFQ cells. Circuit simulation revealed that the measured circuit inductances in the fabricated SFQ cells should allow operating margins of more than +/-20%.
Abstract We fabricated a prototype of a single flux quantum (SFQ) logic circuit for operation near 10 K by using NbN, which has a critical temperature around 16 K. This circuit is fabricated on a 2‐inch silicon (Si) substrate based on the NbN/AlN/NbN tunnel junction having fluctuations in the critical current of ±5% or less from 976 Josephson junctions (JJ). The fabrication of a prototype circuit to generate, propagate, and detect SFQ pulses and the examination of its operation confirmed normal operation up to approximately 9.8 K, which is close to 10 K. In addition, at the operating temperature of 8.5 K, the operations of elementary cells such as a confluence buffer and a T flip‐flop were verified and were successful in the operation of the largest scale circuit, an 8‐bit shift register consisting of 105 JJ. © 2001 Scripta Technica, Electron Comm Jpn Pt 2, 84(10): 34–39, 2001
An analog to digital converter (ADC) using the rapid single flux quantum (RSFQ) logic family implemented in niobium nitride (NbN) technology is described. The circuit was originally developed and demonstrated in niobium technology. An identical circuit was then laid out, fabricated and demonstrated in NbN technology. The chips were fabricated using an eight-layer NbN-based process with Josephson junction critical current density of 500 A/cm/sup 2/. In this paper, we report on the measurement results for a 6-bit flux quantizing ADC which exhibited proper operation and good DC bias margins. We also demonstrate results from an ADC chip operating up to 9.5 K.>
We have developed integrated circuits in rapid single flux quantum (RSFQ) impulse logic based on intrinsically shunted tunnel junctions as the active circuit elements. The circuits have been fabricated using superconductor-insulator-normalconductor-insulator-superconductor (SINIS) multilayer technology. The paper presents experimental results of the operation of various RSFQ circuits realized in different designs and layouts. The circuits comprise dc/SFQ and SFQ/dc converters, Josephson transmission lines (JTLs), T-flipflops, and analog key components. Functionality has been proved; the circuits have been found to operate correctly in switching. The circuits investigated have a critical current density of j/sub C/=400 A/cm/sup 2/ and a characteristic voltage of V/sub C/=165 /spl mu/V, the area of the smallest junction is A=24 /spl mu/m/sup 2/. The junctions exhibit nearly hysteresis-free current-voltage characteristics (hysteresis: less than 7%), the intra-wafer parameter spread for j/sub C/ is below /spl plusmn/8%. The margins of the bias current I/sub b/ of the circuits have been experimentally determined and found to be larger than /spl plusmn/24%. At preset, constant values of I/sub b/, the range of a separate bias current I/sub bsw/ fed to a switching stage integrated between two segments of JTL's is fully covered by the operation margins which are larger than /spl plusmn/56%.
An integrated circuit including all basic components of the recently suggested Resistive Single Flux Quantum (RSFQ) logic family has been designed, fabricated and tested successfully. The circuit includes a generator of periodic SFQ pulses, four buffer/amplifier stages for splitting, channeling and regeneration of the pulses, a detector/load stage, and universal RSFQ logic gate (here performing the NOT function). The 10μm design rule circuit employs 13 active Nb - Al2O3- Nb Josephson junctions with the critical current density ∼ 0.5 kA/cm2. externally shunted by Mo resistors with R 1 Ohm. The shunting provided critical damping of the junctions (\beta_{c}\lsim 1) and reasonable (\sim 500 \muV) IcR product. The circuit operation has been tested by measurement of dc voltages\bar{V}_{i}across various Josephson junctions as functions of the dc current through the pulse generator. Correct and stable operation of the circuit for the clock frequencies from 0 to ∼30 GHz has been demonstrated.
The paper presents the determination of the high-frequency performance of Rapid Single Flux Quantum (RSFQ) circuits fabricated in superconductor-insulator-normal metal-insulator-superconductor (SINIS) technology. Circuits of different designs have been realized and were experimentally investigated, including specially designed T flip-flop (TFF) structures and circuits consisting of a switch terminated in Josephson transmission lines. For TFF circuits, the operational functionality was investigated in the frequency range from dc up to nearly 200 GHz. Two frequency domains were found. In the first domain, ranging up to frequencies of 80 GHz (f/sub C//spl cong/Y/sub C///spl Phi//sub 0/), correct digital operation of the device was ascertained. Beyond this range a second domain was found, ranging to nearly 200 GHz, for which quasi-analog frequency dividing is assumed. The bias current margins are /spl plusmn/30% at 40 GHz and /spl plusmn/15% between 130 GHz and 200 GHz. For circuits consisting of a switch, the operational functionality was proved in the frequency range from dc up to 50 GHz, with bias current margins of more than /spl plusmn/20%. The critical current density of the circuits is j/sub C//spl cong/750 A/cm/sup 2/. The smallest junction area is about A=12 /spl mu/m/sup 2/, and the characteristic voltage is V/sub C/=170 /spl mu/V.