Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE MTT-S International Microwave Symposium digest

A 230 GHz low noise subharmonically pumped SIS mixer

K. C. Xiao, Hideo Ogawa, Akira Mizuno, Yasuo Fukui

Published Nov 7, 2002• 2 citations
Publisher

Abstract

A 230 GHz Low Noise Subharmonically Pumped (SHP) SIS mixer has been developed and tested at 115 GHz LO. The mixer has a two backshorts waveguide structure and employs an array of four 1.7 /spl mu/m/sup 2/ Nb/AlO/sub x//Nb SIS junctions in series with /spl omega/RnC/spl sim/3 at 230 GHz. Harmonic quantum mixing occurred over the whole experimental frequency range of 208-234 GHz (LO:114-117 GHz), with the corresponding DSB noise temperatures of lower than 150 K and a lowest value of 75 K at /spl sim/230 GHz. The present noise results are believed to be the lowest yet reported for a SHP mixer.

DOI
10.1109/mwsym.2000.861130

Related papers

An experimental study of harmonic sis mixing at 205-235 ghz

Kecheng Xiao, Hideo Ogawa, Yasuo Fukui

A 230-GHz subharmonically pumped waveguide mixer employing superconducting tunnel junctions has been developed. We present, in this paper, an experimental study of harmonic superconductor-insulator-superconductor (SIS) mixing at 230 GHz, focusing mainly on its noise behavior. The mixer has a double-tuned waveguide structure and employs an array of four 1.7-/spl mu/m/sup 2/ Nb-AlOx-Nb SIS junctions in series, with /spl omega/R/sub n/C/sub j//spl sim/3 at 230 GHz. Harmonic quantum mixing occurred over an experimental frequency range of 205-235 GHz (local oscillator: 112.5-117.5 GHz), exhibiting corresponding double sideband noise temperatures of lower than 150 K, with a lowest value of 75 K at /spl sim/230 GHz. The measured mixer noise is believed to be the lowest yet reported for a mixer using subharmonic-pump configuration at this frequency. A phenomenon that we attribute to the third harmonic SIS mixing has also been observed.

IEEE Transactions on Applied Superconductivity•Dec 1, 2003•3 citations

A low noise 230 GHz heterodyne receiver employing 0.25- mu m/sup 2/ area Nb-AlO/sub x/-Nb tunnel junctions

J. Kooi, M. Chan, Tom G. Phillips +2 more

The authors report recent results for a full-height rectangular waveguide mixer with an integrated IF matching network. Two 0.25 mu m/sup 2/ Nb-AlO/sub x/-Nb superconducting-insulating-superconducting (SIS) tunnel junctions with a current density of approximately=8500 A/cm/sup 2/ and omega RC of approximately=2.5 at 230 GHz have been tested. One of these quasiparticle tunnel junctions is currently being used at the Caltech Submillimeter Observatory in Hawaii. Detailed measurement of the receiver noise have been made from 200-290 GHz for both junctions at 4.2 K. The lowest receiver noise temperatures were recorded at 239 GHz, measuring 48 K DSB at 4.2 K and 40 K DSB at 2.1 K. The 230-GHz receiver incorporates a one-octave-wide integrated low-pass filter and matching network which transforms the pumped IF junction impedance to 50 Omega over a wide range of impedances.>

IEEE Transactions on Microwave Theory and Techniques•May 1, 1992•39 citations

Low noise broadband fixed tuned SIS waveguide mixers at 660 and 800 GHz

Cornelia E. Honingh, Sybille Haas, D. Hottgenroth +2 more

We present measurements and simulations of mixer performance around 660 GHz and around 800 GHz. We use Nb-Al/sub 2/O/sub 3/-Nb tunnel junctions with areas of 0.9 /spl mu/m/sup 2/ and 0.7 /spl mu/m/sup 2/, and RA-products of 14.5 /spl Omega/(/spl mu/m)/sup 2/ and 13 /spl Omega/(/spl mu/m)/sup 2/ for 660 GHz and 800 GHz. Both junctions have an integrated tuning structure made of niobium that consists of a series resonant stub and a quarter lambda transformer. The waveguide mixerblock has no additional adjustable tuning elements. It contains just a waveguide cavity and a substrate channel across it. A horn is carefully adjusted to the cavity and flanged to the block. The measured receiver noise temperatures from 630-690 GHz are below 190 K with a best value of 120 K at 655 GHz. From 780-820 GHz they are below 950 K with a best value of 780 K at 792 GHz. When the operating temperature is reduced from 4.2 K to 2.5 K, a reduction in noise temperature from 830 K to 660 K is observed at 810 GHz. The mixer performance is simulated using the quantum theory of mixing. The simulated performance shows a fairly good agreement with the measured one.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•21 citations

A low noise 410-495 GHz Nb/Al/sub 2/O/sub 3//Nb SIS waveguide mixer

Gert J. de Lange, Cornelia E. Honingh, M. M. T. M. Dierichs +5 more

The noise and gain of a heterodyne waveguide mixer using Nb/Al/sub 2/O/sub 3//Nb superconducting tunnel junctions were measured in the 400-500-GHz frequency range. Three different arrays of two junctions in series are analyzed. The minimum receiver noise temperature is 120 K DSB at 480 GHz, measured with an array having integrated tuning stubs. The authors compare data of the pumped I-V curves with the Werthammer-Tucker theory and demonstrate an excellent agreement at frequencies up to 500 GHz. For an array without integrated tuning stubs. a mixer noise temperature of 90+or-30 K and a DSB mixer gain of -12.5+or-0.6 dB were measured. A comparison of the measured gain versus bias voltage with the quantum theory of mixing shows good qualitative agreement, indicating the applicability of this theory to Nb tunnel junctions up to 500 GHz. The noise temperature of an array with a lower gap voltage is 220 K at 495 GHz. This frequency is 85% of the reduced gap frequency, indicating that Nb superconductor insulator-superconductor (SIS) mixers can be used up at least the gap frequency of 680 GHz.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•13 citations

Noise and gain in frequency mixers with NbN SIS junctions

Alexandre Karpov, B. Plathner, J. Blondel +4 more

We study noise and conversion gain in the SIS mixers with Nb/MgO/NbN junctions at the millimeter and submillimeter wavelengths in order to estimate the possibility to extent the low noise operation towards the theoretical limit of 4/spl Delta//h=2.4 THz. We present as preliminary result the lowest achieved receiver noise with NbN SIS junctions of 65 K with conversion gain of -6 dB at 162 GHz and 230 K receiver noise with conversion gain of -10 dB at 306 GHz. The junction area is 2 /spl mu/m/sup 2/ and Josephson critical current density is 1.4 KA/cm/sup 2/. The optimum R/sub N//spl omega/C of NbN junction for mixers is estimated as 600 GHz/V. In preliminary tests the junctions R/sub N//spl omega/C is 10-20 time superior to the optimum and a significant improvement of NbN SIS mixers may be expected. The noise sources in the NbN SIS junctions are studied and a possible mixer sensitivity improvement is discussed. The thermal properties of the SIS NbN are studied. The frequency limit of the low loss integrated tuning structure in NbN is estimated as at least as 1.5 THz.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•9 citations

Performance of a two-junction array SIS-mixer operating around 345 GHz

Cornelia E. Honingh, Gert J. de Lange, M. M. T. M. Dierichs +3 more

The authors have made a detailed study of the gain and noise of a SIS (superconductor-insulator-superconductor) heterodyne receiver at 345 GHz. An array of two Nb-Al/sub 2/O/sub 3/-Nb SIS junctions in series are used as the mixing element. The array is operated in a waveguide mount with a backshort and an E-plane tuner. The best receiver noise temperature achieved is 140 K DSB (double sideband). The embedding impedances were determined by fitting theory to the measured pumped curves. High-quality fits were obtained, providing the first detailed test of the Tucker-theory at frequencies above 300 GHz. The impedances found by this method are in very good agreement with impedances measured in a scale model at 3.3 GHz. From these embedding impedances, the gain and noise of the mixer were calculated over a full bias range using the Tucker theory in the three-port low-IF approximation. The measured dependence of mixer gain and noise on bias voltage, pump power and embedding impedance is in good agreement with theory. However the absolute values show discrepancies that appear to be independent of the bias parameters of the mixer.>

IEEE Transactions on Microwave Theory and Techniques•Apr 1, 1993•14 citations
A 230 GHz Low Noise Subharmonically Pumped (SHP) SIS mixer has been developed and tested at 115 GHz LO. The mixer has a two backshorts waveguide structure and employs an array of four 1.7 /spl mu/m/sup 2/ Nb/AlO/sub x//Nb SIS junctions in series with /spl omega/RnC/spl sim/3 at 230 GHz. Harmonic quantum mixing occurred over the whole experimental frequency range of 208-234 GHz (LO:114-117 GHz), with the corresponding DSB noise temperatures of lower than 150 K and a lowest value of 75 K at /spl sim/230 GHz. The present noise results are believed to be the lowest yet reported for a SHP mixer.
A 230-GHz subharmonically pumped waveguide mixer employing superconducting tunnel junctions has been developed. We present, in this paper, an experimental study of harmonic superconductor-insulator-superconductor (SIS) mixing at 230 GHz, focusing mainly on its noise behavior. The mixer has a double-tuned waveguide structure and employs an array of four 1.7-/spl mu/m/sup 2/ Nb-AlOx-Nb SIS junctions in series, with /spl omega/R/sub n/C/sub j//spl sim/3 at 230 GHz. Harmonic quantum mixing occurred over an experimental frequency range of 205-235 GHz (local oscillator: 112.5-117.5 GHz), exhibiting corresponding double sideband noise temperatures of lower than 150 K, with a lowest value of 75 K at /spl sim/230 GHz. The measured mixer noise is believed to be the lowest yet reported for a mixer using subharmonic-pump configuration at this frequency. A phenomenon that we attribute to the third harmonic SIS mixing has also been observed.
The authors report recent results for a full-height rectangular waveguide mixer with an integrated IF matching network. Two 0.25 mu m/sup 2/ Nb-AlO/sub x/-Nb superconducting-insulating-superconducting (SIS) tunnel junctions with a current density of approximately=8500 A/cm/sup 2/ and omega RC of approximately=2.5 at 230 GHz have been tested. One of these quasiparticle tunnel junctions is currently being used at the Caltech Submillimeter Observatory in Hawaii. Detailed measurement of the receiver noise have been made from 200-290 GHz for both junctions at 4.2 K. The lowest receiver noise temperatures were recorded at 239 GHz, measuring 48 K DSB at 4.2 K and 40 K DSB at 2.1 K. The 230-GHz receiver incorporates a one-octave-wide integrated low-pass filter and matching network which transforms the pumped IF junction impedance to 50 Omega over a wide range of impedances.>
We present measurements and simulations of mixer performance around 660 GHz and around 800 GHz. We use Nb-Al/sub 2/O/sub 3/-Nb tunnel junctions with areas of 0.9 /spl mu/m/sup 2/ and 0.7 /spl mu/m/sup 2/, and RA-products of 14.5 /spl Omega/(/spl mu/m)/sup 2/ and 13 /spl Omega/(/spl mu/m)/sup 2/ for 660 GHz and 800 GHz. Both junctions have an integrated tuning structure made of niobium that consists of a series resonant stub and a quarter lambda transformer. The waveguide mixerblock has no additional adjustable tuning elements. It contains just a waveguide cavity and a substrate channel across it. A horn is carefully adjusted to the cavity and flanged to the block. The measured receiver noise temperatures from 630-690 GHz are below 190 K with a best value of 120 K at 655 GHz. From 780-820 GHz they are below 950 K with a best value of 780 K at 792 GHz. When the operating temperature is reduced from 4.2 K to 2.5 K, a reduction in noise temperature from 830 K to 660 K is observed at 810 GHz. The mixer performance is simulated using the quantum theory of mixing. The simulated performance shows a fairly good agreement with the measured one.
The noise and gain of a heterodyne waveguide mixer using Nb/Al/sub 2/O/sub 3//Nb superconducting tunnel junctions were measured in the 400-500-GHz frequency range. Three different arrays of two junctions in series are analyzed. The minimum receiver noise temperature is 120 K DSB at 480 GHz, measured with an array having integrated tuning stubs. The authors compare data of the pumped I-V curves with the Werthammer-Tucker theory and demonstrate an excellent agreement at frequencies up to 500 GHz. For an array without integrated tuning stubs. a mixer noise temperature of 90+or-30 K and a DSB mixer gain of -12.5+or-0.6 dB were measured. A comparison of the measured gain versus bias voltage with the quantum theory of mixing shows good qualitative agreement, indicating the applicability of this theory to Nb tunnel junctions up to 500 GHz. The noise temperature of an array with a lower gap voltage is 220 K at 495 GHz. This frequency is 85% of the reduced gap frequency, indicating that Nb superconductor insulator-superconductor (SIS) mixers can be used up at least the gap frequency of 680 GHz.>
We study noise and conversion gain in the SIS mixers with Nb/MgO/NbN junctions at the millimeter and submillimeter wavelengths in order to estimate the possibility to extent the low noise operation towards the theoretical limit of 4/spl Delta//h=2.4 THz. We present as preliminary result the lowest achieved receiver noise with NbN SIS junctions of 65 K with conversion gain of -6 dB at 162 GHz and 230 K receiver noise with conversion gain of -10 dB at 306 GHz. The junction area is 2 /spl mu/m/sup 2/ and Josephson critical current density is 1.4 KA/cm/sup 2/. The optimum R/sub N//spl omega/C of NbN junction for mixers is estimated as 600 GHz/V. In preliminary tests the junctions R/sub N//spl omega/C is 10-20 time superior to the optimum and a significant improvement of NbN SIS mixers may be expected. The noise sources in the NbN SIS junctions are studied and a possible mixer sensitivity improvement is discussed. The thermal properties of the SIS NbN are studied. The frequency limit of the low loss integrated tuning structure in NbN is estimated as at least as 1.5 THz.
The authors have made a detailed study of the gain and noise of a SIS (superconductor-insulator-superconductor) heterodyne receiver at 345 GHz. An array of two Nb-Al/sub 2/O/sub 3/-Nb SIS junctions in series are used as the mixing element. The array is operated in a waveguide mount with a backshort and an E-plane tuner. The best receiver noise temperature achieved is 140 K DSB (double sideband). The embedding impedances were determined by fitting theory to the measured pumped curves. High-quality fits were obtained, providing the first detailed test of the Tucker-theory at frequencies above 300 GHz. The impedances found by this method are in very good agreement with impedances measured in a scale model at 3.3 GHz. From these embedding impedances, the gain and noise of the mixer were calculated over a full bias range using the Tucker theory in the three-port low-IF approximation. The measured dependence of mixer gain and noise on bias voltage, pump power and embedding impedance is in good agreement with theory. However the absolute values show discrepancies that appear to be independent of the bias parameters of the mixer.>