Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optics Express

High quality factor 1-D Er^3+-activated dielectric microcavity fabricated by RF-sputtering

Sreeramulu Valligatla, Alessandro Chiasera, Stefano Varas, Nicola Bazzanella, D. Narayana Rao, Giancarlo Cesare Righini, Maurizio Ferrari

Published Aug 31, 2012• 72 citations
Publisher

Abstract

Rare earth-activated 1-D photonic crystals were fabricated by RF-sputtering technique. The cavity is constituted by an Er3+-doped SiO2 active layer inserted between two Bragg reflectors consisting of ten pairs of SiO2/TiO2 layers. Scanning electron microscopy is employed to put in evidence the quality of the sample, the homogeneities of the layers thickness and the good adhesion among them. Near infrared transmittance and variable angle reflectance spectra confirm the presence of a stop band from 1500 nm to 2000 nm with a cavity resonance centered at 1749 nm at 0° and a quality factor of 890. The influence of the cavity on the ⁴I₁₃/₂ -->⁴I₁₅/₂ emission band of Er3+ ion is also demonstrated.

DOI
10.1364/oe.20.021214

Related papers

Photonic Crystal Microcavity Amplifier

D. Biallo, Antonella D’Orazio, M. De Sario +3 more

Summary form only given: Amplification in rare-earth doped solid state planar optical structures has attracted a lot of interest in recent years due to the fact that the rare earth ions show sharp absorption and emission bands and relatively long luminescence lifetimes. In particular the erbium (Er) ion is very attractive because of its intra 4f-transition from the first excited state to the ground state around 1.53 mum (4I13/2-4I15/2). The main problem of the erbium doped waveguide amplifiers (EDWAs) is that high values of the Er3+concentration are required to reach high gain figures in a compact length, but in this way the concentration quenching effects become very considerable and detrimental to the optical gain, since they reduce the population in the first excited state. A good solution to overcome this dramatic drawback is to consider erbium doped photonic crystal amplifier (EDPCA). In fact the small group velocity of electromagnetic eigenmodes brings about the enhancement of stimulated emission if the photonic crystals are doped by active media as the rare earth ions E3+r or Yt3+. This phenomenon originates from the long interaction time between radiation field and the matter caused by the small group velocity near the edge of the photonic band gap. The efficient confinement of light is achievable not only by tuning the input signal at the band edge of the gap of the photonic crystal but it is also obtainable by introducing local defects inside photonic crystals. The density of electromagnetic states inside a cavity is significantly modified and the spontaneous emission of atoms in a cavity can be either enhanced or inhibited. Erbium doped silica-titania one-dimensional photonic crystal microcavities have been analyzed by solving the erbium rate equations and the Maxwell equations by means of an auxiliary differential equation finite difference time domain technique. Since the performance of optical amplifiers depends on the populations of the energy levels participating in radiative transitions, determined principally by the distribution and concentration of the rare-earth ions and by the pumping conditions, the relations between these parameters and the transmittance of the EDPCMA have been studied

International Conference on Transparent Optical Networks•Jun 1, 2006•0 citations

High quality factor nanophotonic resonators in bulk rare-earth doped crystals

Tian Zhong, Jake Rochman, Jonathan M. Kindem +2 more

Numerous bulk crystalline materials exhibit attractive nonlinear and luminescent properties for classical and quantum optical applications. A chip-scale platform for high quality factor optical nanocavities in these materials will enable new optoelectronic devices and quantum light-matter interfaces. In this article, photonic crystal nanobeam resonators fabricated using focused ion beam milling in bulk insulators, such as rare-earth doped yttrium orthosilicate and yttrium vanadate, are demonstrated. Operation in the visible, near infrared, and telecom wavelengths with quality factors up to 27,000 and optical mode volumes close to one cubic wavelength is measured. These devices enable new nanolasers, on-chip quantum optical memories, single photon sources, and non-linear devices at low photon numbers based on rare-earth ions. The techniques are also applicable to other luminescent centers and crystal.

arXiv:1512.03947•Optics Express•Jan 7, 2016•49 citations

Controlled Atomic-like Spontaneous Emission from Implanted Erbium in a Si/SiO2 Microcavity

Arjen M. Vredenberg, N. E. J. Hunt, E. Fred Schubert +3 more

Since the advent of vertical cavity surface-emitting lasers, a renewed interest has also emerged for the spontaneous emission from Fabry-Pérot microcavities. Changes in spontaneous emission characteristics in a 1D microcavity were predicted long ago,1 but have been demonstrated only recently in the optical domain for solid-state, e.g. semiconductor, structures where changes in spectral purity, lifetime, and emission intensity were observed.2 However, the interpretation of these effects is somewhat obscure, because these structures are highly absorbing and often involve band-to-band, rather than atomic, transitions. In the present study, we use optically transparent Si/SiO2 cavities, consisting of two coplanar Si/SiO2 distributed Bragg reflectors (DBR) around a (λ/2) SiO2 active region, which was doped with ~0.2 at.% Er3+ ions through MeV ion implantation. The Er3+ ions in SiO2 exhibit a sharp, atomic-like, intra-4f transition around λem=1.54 μm, which is effectively shielded by the outerlying filled 5s2 and 5p6 shells. Recently, we reported on the considerable enhancement of the spontaneous emission intensity out of such an Er-doped microcavity.3 In this paper, we present a more detailed study of the modified spontaneous emission, including fluorescence decay measurements to study the effect of the cavity on the spontaneous emission rate.

Quantum Optoelectronics•Jan 1, 1993•2 citations

Controlled spontaneous emission in erbium-doped microphotonic materials

Jeroen Kalkman

Erbium is a rare-earth metal that, when incorporated in a solid, can emit light at a wavelength of 1.5 μm. It plays a key role in current day telecommunication technology as the principle ingredient of optical fiber amplifiers. In this thesis the control of the Er spontaneous emission in three different types of microphotonic materials is described. Part I of this thesis focuses on the effect of a metallo-dielectric interface on the spontaneous emission of optical emitters in silica glass. It is shown that Er ions near a Ag interface can couple to surface plasmons (SPs) via a near-field interaction. By coupling SPs out into the far field, large changes in the Er photoluminescence emission distribution, spectra, and polarization can be observed. The excitation of SPs also results in an increase of the Er photoluminescence decay rate. The observed decay rates are in good agreement with calculations based on a classical dipole oscillator model. From the change in photoluminescence decay rate of Si nanocrystals near a Ag interface it is shown that Si nanocrystals can efficiently excite SPs and have an internal quantum efficiency of 77 %. Part II focuses on the effect of a microcavity on the spontaneous emission of Er and describes how ion implantation can be used to dope dielectric microresonators with optically active Er ions. The fabrication and characterization of an Er ion-implanted silica microsphere resonator is described that shows lasing at 1.5 μm when pumped above its lasing threshold. Ion implantation is also used to dope toroidal microcavities on a Si chip with Er. The microtoroids are doped by either pre-implantation into the SiO2 base material, or by post-implantation in a fully fabricated microtoroid. The optical activation of Er ions in the microtoroid is investigated and Er lasing at 1.5 μm is observed for both types of microcavities with the lowest threshold (4.5 μW) for the pre-implanted microtoroids. Part III describes the fabrication of an Er-doped Si-inverse opal photonic crystal. These photonic crystals can potentially have a photonic bandgap that can fully inhibit the spontaneous emission of on optical emitter. Fabrication criteria are derived for such a photonic crystal, based on the lattice parameter, filling fraction, and Si refractive index. In the opal photonic crystal composed of both Si and SiO2 we show that Er ions can be selectively excited in both the Si and SiO2 part of the photonic crystal by changing the excitation wavelength and/or the measurement temperature.

•Mar 9, 2005•3 citations

Er 3+ in strong light-confining microcavity

Michal F. Lipson, Lionel C. Kimerling

Er 3+ ions produce a sharp line emission that has small absorption cross section, long radiative lifetime, and is independent of external perturbations. These optical properties of the Er3+ ions limit the pumping efficiency and tunability of the emission line. In this work we present a study in which Er3+ emission was modified by coupling an ensemble of Er3+ ions to a microcavity resonance. The optical response of an optical cavity that consists of an Er2O3 layer confined between Si/SiO2 distributed Bragg reflectors is studied. When the cavity is in resonance with the optical transition of the Er3+ ions, the resonances in the reflectivity spectra split. The results are explained by a standard semiclassical model of atom–photon coupling.

Applied Physics Letters•Aug 21, 2000•23 citations

Rare-earth ion-integrated silicon photonics for quantum networks

Robert M. Pettit, Ananthesh Sundaresh, Victoria Rosborough +9 more

Rare-earth ion defects in solid-state hosts have emerged as a promising candidate for emissive quantum memories owing to their inherent spin–photon interface and long optical and spin coherence times. Erbium (Er3+) in particular has optical transitions in the C-band making it well suited to the use of existing telecom technology infrastructure. In this work, we present a platform to integrate rare-earth ions into standard silicon photonic circuits. Erbium is co-deposited in CMOS-compatible TiO2 host films onto SOI and patterned into high Purcell factor photonic crystal cavities. Purcell factors in excess of 500 are observed and transient spectral hole burning and photoluminescence excitation scans reveal homogeneous linewidths below 15 MHz. Additionally, we show that photonic wirebonding can provide a solution for low-loss and thermally stable fiber-to-chip coupling.

SPIE Quantum Information Science, Sensing, and Computation•Jun 7, 2024•0 citations
Rare earth-activated 1-D photonic crystals were fabricated by RF-sputtering technique. The cavity is constituted by an Er3+-doped SiO2 active layer inserted between two Bragg reflectors consisting of ten pairs of SiO2/TiO2 layers. Scanning electron microscopy is employed to put in evidence the quality of the sample, the homogeneities of the layers thickness and the good adhesion among them. Near infrared transmittance and variable angle reflectance spectra confirm the presence of a stop band from 1500 nm to 2000 nm with a cavity resonance centered at 1749 nm at 0° and a quality factor of 890. The influence of the cavity on the ⁴I₁₃/₂ -->⁴I₁₅/₂ emission band of Er3+ ion is also demonstrated.
Summary form only given: Amplification in rare-earth doped solid state planar optical structures has attracted a lot of interest in recent years due to the fact that the rare earth ions show sharp absorption and emission bands and relatively long luminescence lifetimes. In particular the erbium (Er) ion is very attractive because of its intra 4f-transition from the first excited state to the ground state around 1.53 mum (4I13/2-4I15/2). The main problem of the erbium doped waveguide amplifiers (EDWAs) is that high values of the Er3+concentration are required to reach high gain figures in a compact length, but in this way the concentration quenching effects become very considerable and detrimental to the optical gain, since they reduce the population in the first excited state. A good solution to overcome this dramatic drawback is to consider erbium doped photonic crystal amplifier (EDPCA). In fact the small group velocity of electromagnetic eigenmodes brings about the enhancement of stimulated emission if the photonic crystals are doped by active media as the rare earth ions E3+r or Yt3+. This phenomenon originates from the long interaction time between radiation field and the matter caused by the small group velocity near the edge of the photonic band gap. The efficient confinement of light is achievable not only by tuning the input signal at the band edge of the gap of the photonic crystal but it is also obtainable by introducing local defects inside photonic crystals. The density of electromagnetic states inside a cavity is significantly modified and the spontaneous emission of atoms in a cavity can be either enhanced or inhibited. Erbium doped silica-titania one-dimensional photonic crystal microcavities have been analyzed by solving the erbium rate equations and the Maxwell equations by means of an auxiliary differential equation finite difference time domain technique. Since the performance of optical amplifiers depends on the populations of the energy levels participating in radiative transitions, determined principally by the distribution and concentration of the rare-earth ions and by the pumping conditions, the relations between these parameters and the transmittance of the EDPCMA have been studied
Numerous bulk crystalline materials exhibit attractive nonlinear and luminescent properties for classical and quantum optical applications. A chip-scale platform for high quality factor optical nanocavities in these materials will enable new optoelectronic devices and quantum light-matter interfaces. In this article, photonic crystal nanobeam resonators fabricated using focused ion beam milling in bulk insulators, such as rare-earth doped yttrium orthosilicate and yttrium vanadate, are demonstrated. Operation in the visible, near infrared, and telecom wavelengths with quality factors up to 27,000 and optical mode volumes close to one cubic wavelength is measured. These devices enable new nanolasers, on-chip quantum optical memories, single photon sources, and non-linear devices at low photon numbers based on rare-earth ions. The techniques are also applicable to other luminescent centers and crystal.
Since the advent of vertical cavity surface-emitting lasers, a renewed interest has also emerged for the spontaneous emission from Fabry-Pérot microcavities. Changes in spontaneous emission characteristics in a 1D microcavity were predicted long ago,1 but have been demonstrated only recently in the optical domain for solid-state, e.g. semiconductor, structures where changes in spectral purity, lifetime, and emission intensity were observed.2 However, the interpretation of these effects is somewhat obscure, because these structures are highly absorbing and often involve band-to-band, rather than atomic, transitions. In the present study, we use optically transparent Si/SiO2 cavities, consisting of two coplanar Si/SiO2 distributed Bragg reflectors (DBR) around a (λ/2) SiO2 active region, which was doped with ~0.2 at.% Er3+ ions through MeV ion implantation. The Er3+ ions in SiO2 exhibit a sharp, atomic-like, intra-4f transition around λem=1.54 μm, which is effectively shielded by the outerlying filled 5s2 and 5p6 shells. Recently, we reported on the considerable enhancement of the spontaneous emission intensity out of such an Er-doped microcavity.3 In this paper, we present a more detailed study of the modified spontaneous emission, including fluorescence decay measurements to study the effect of the cavity on the spontaneous emission rate.
Erbium is a rare-earth metal that, when incorporated in a solid, can emit light at a wavelength of 1.5 μm. It plays a key role in current day telecommunication technology as the principle ingredient of optical fiber amplifiers. In this thesis the control of the Er spontaneous emission in three different types of microphotonic materials is described. Part I of this thesis focuses on the effect of a metallo-dielectric interface on the spontaneous emission of optical emitters in silica glass. It is shown that Er ions near a Ag interface can couple to surface plasmons (SPs) via a near-field interaction. By coupling SPs out into the far field, large changes in the Er photoluminescence emission distribution, spectra, and polarization can be observed. The excitation of SPs also results in an increase of the Er photoluminescence decay rate. The observed decay rates are in good agreement with calculations based on a classical dipole oscillator model. From the change in photoluminescence decay rate of Si nanocrystals near a Ag interface it is shown that Si nanocrystals can efficiently excite SPs and have an internal quantum efficiency of 77 %. Part II focuses on the effect of a microcavity on the spontaneous emission of Er and describes how ion implantation can be used to dope dielectric microresonators with optically active Er ions. The fabrication and characterization of an Er ion-implanted silica microsphere resonator is described that shows lasing at 1.5 μm when pumped above its lasing threshold. Ion implantation is also used to dope toroidal microcavities on a Si chip with Er. The microtoroids are doped by either pre-implantation into the SiO2 base material, or by post-implantation in a fully fabricated microtoroid. The optical activation of Er ions in the microtoroid is investigated and Er lasing at 1.5 μm is observed for both types of microcavities with the lowest threshold (4.5 μW) for the pre-implanted microtoroids. Part III describes the fabrication of an Er-doped Si-inverse opal photonic crystal. These photonic crystals can potentially have a photonic bandgap that can fully inhibit the spontaneous emission of on optical emitter. Fabrication criteria are derived for such a photonic crystal, based on the lattice parameter, filling fraction, and Si refractive index. In the opal photonic crystal composed of both Si and SiO2 we show that Er ions can be selectively excited in both the Si and SiO2 part of the photonic crystal by changing the excitation wavelength and/or the measurement temperature.
Er 3+ ions produce a sharp line emission that has small absorption cross section, long radiative lifetime, and is independent of external perturbations. These optical properties of the Er3+ ions limit the pumping efficiency and tunability of the emission line. In this work we present a study in which Er3+ emission was modified by coupling an ensemble of Er3+ ions to a microcavity resonance. The optical response of an optical cavity that consists of an Er2O3 layer confined between Si/SiO2 distributed Bragg reflectors is studied. When the cavity is in resonance with the optical transition of the Er3+ ions, the resonances in the reflectivity spectra split. The results are explained by a standard semiclassical model of atom–photon coupling.
Rare-earth ion defects in solid-state hosts have emerged as a promising candidate for emissive quantum memories owing to their inherent spin–photon interface and long optical and spin coherence times. Erbium (Er3+) in particular has optical transitions in the C-band making it well suited to the use of existing telecom technology infrastructure. In this work, we present a platform to integrate rare-earth ions into standard silicon photonic circuits. Erbium is co-deposited in CMOS-compatible TiO2 host films onto SOI and patterned into high Purcell factor photonic crystal cavities. Purcell factors in excess of 500 are observed and transient spectral hole burning and photoluminescence excitation scans reveal homogeneous linewidths below 15 MHz. Additionally, we show that photonic wirebonding can provide a solution for low-loss and thermally stable fiber-to-chip coupling.