We present additional RSFQ superconductive digital electronics logic gates that have been developed to complement already existing gates. These gates are the NOR, NAND and XNOR. The gates were designed, simulated and laid out for fabrication in both IPHT's FLUXONICS 1 kA/cm2and Hypres’ 4.5 kA/cm2processes. Layout circuit parameters such as inductance were extracted to compare these with design values. Good working margins were obtained after several steps of manual circuit optimisation during the design and simulation stages. NioPulse, superconductor circuit design software developed by NioCAD in South Africa, was used and evaluated during the design process.
We present additional RSFQ superconductive digital electronics logic gates that have been developed to complement already existing gates. These gates are the NOR, NAND and XNOR. The gates were designed, simulated and laid out for fabrication in both IPHT's FLUXONICS 1 kA/cm2and Hypres’ 4.5 kA/cm2processes. Layout circuit parameters such as inductance were extracted to compare these with design values. Good working margins were obtained after several steps of manual circuit optimisation during the design and simulation stages. NioPulse, superconductor circuit design software developed by NioCAD in South Africa, was used and evaluated during the design process.
ENGLISH ABSTRACT: Rapid Single Flux Quantum (RSFQ) cells are key in the design of complex and applicable RSFQ electronic circuits. These cells are low-level circuit elements that are used repeatedly to build larger, applicable RSFQ circuitry. Making these cells simple to layout and manufacture, but reliable for extensive use demands a careful development process for RSFQ cells. Cell functionality is verified through simulations, thereafter the cell is laid out in special software packages. Inductance of on-chip superconductor structures is extracted through careful modelling with numerical field solver software. A cell library has been developed by incorporating existing or published cells after further analysis and optimization, as well as developing new cells. Cells that have been adapted into the library include the Josephson transmission line (JTL), Splitter, Merger, D-Flip Flop (DFF), T-Flip Flop (TFF), NOT, AND, OR and XOR, DC-SFQ and SFQ-DC and PTL Driver and Receivers. New cells include NOR, NAND and XNOR. The cells were designed for the IPHT’s RSFQ1D 1kA/cmª and Hypres’ 4.5kA/cmª processes. The cells in the library have good bias current operating margins obtained through simulations (> ±26%). All cells have all the parameters listed in the thesis including extracted inductance values. In order to have a complete and verified RSFQ cell library, cells have been sent for fabrication at IPHT and Hypres facilities. These cells can now be tested on-chip, in the laboratory, to establish functionality and practical bias current margins. All test signal patterns and bias currents required for testing are defined to allow co-workers or collaborators to test the cells.
The development of an RSFQ cell library for the world's fastest superconducting digital family is hereby presented. Cells ranging from the basic JTL to the more complex NOR gate were laid out and are ready for fabrication. In addition, cell parameters were carefully estimated and inductance extracted using special software tools. To ensure that the cells work with known parameter margins, on-chip testing of these cells are done in the laboratory. Cells ready for fabrication include the JTL, Splitter, Merger, PTL Driver and Receiver, T-flip flop, D-flip flop, OR, NOR, AND, XOR and the NOT, with the XNOR and NAND to be developed next. We discuss test steps and verification of the cells.
ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.
We have developed a cell library for superconducting large scale integrated (LSI) digital circuits based on Single Flux Quantum (SFQ) devices. The circuits were designed for a 6-kA/cm2Nb/AlOx/Nb junction process with 10 mask levels including one ground plane and two Nb wiring layers. The initial design and optimization of the circuit parameters were achieved by means of the optimization functions in a circuit simulator, PSCAN2, to ensure that important circuit parameters, Josephson critical current (IC), bias current (Ibias), and inductance satisfied minimal margin requirements. Critical margins of ICand Ibiaswere then further improved manually. To compensate the scattering in the circuit parameters from fabrication by design as much as possible, the critical junction parameters were optimized to further centralize the IC. The library cells were laid out following our design rules determined by systematic experiments on process control monitors (PCM). Basic cells including Josephson transmission lines, splitters, confluence buffers, D flip-flops, T flip-flops, and XOR and NDRO gates were designed, fabricated, and successfully tested at low frequencies. Wide overlaps of the operating regions for the common bias voltages were confirmed.
Superconductor digital technology based on Rapid Single Flux Quantum logic (RSFQ) offers more than 50 times gain in speed and more than 100 reduction in power consumption over mainstream CMOS devices. However, the necessity of cooling down to 4 K and modest degree of integration density currently available mean that employing RSFQ is reasonable only for the tasks that are impossible or ineffective to implement in CMOS technology. One of the promising applications of the RSFQ technology is Digital Signal Processing (DSP) for telecommunications. Interference cancellation is a bottleneck for all existing systems in terms of the performance gain that is theoretically possible and technically realizable using conventional technology. The crucial factor is computational complexity required to handle multiple access interference. The general approach is to compute the interference using available data about propagation channels and then either remove it from received signal or use to predistort the transmitted signal. Computation of the interference matrix can easily fall into 100 Gops range, furthermore, the most e±cient algorithms are based on successive iterations. This requires not only high overall performance of the DSP but also high actual clock rate.This thesis reports a proposed architecture of an RSFQ Successive Interference Canceller and a design of an RSFQ Digital Signal Processor based on hybrid RSFQ-CMOS memory suitable for a general matrix on matrix multiplication algorithm. The processor consists of an RSFQ Multiply-Accumulate Unit, memory caches and a synchronization block, partitioned into multiple chips, and a large CMOS memory.The complexity of the RSFQ DSP is 10x10 multiplication, rounding to 14 bits, 18 bits accumulator length and 3.7 Kb memory cache. In order to implement the RSFQ DSP, we have developed approach to simulate and describe the RSFQ circuits using VHDL. The maximum simulated clock frequency is equal to 24 GHz for Hypres 4.5 kA/cm2 process and optimum communication bandwidth with CMOS memory is 2 Gbps.Components of the processor such as 4x4 two's complement and 5x5 parallel multipliers, 4x5, 20x5 and 4x15 parallel shift registers, a 5-bit serial adder have been designed and experimentally tested. The simplified version of the RSFQ DSP consisting of a 4x4 MAC with rounding to 5 bits and 17x6 memory caches has been designed for Hypres 4.5 kA/cm2 process and fabricated.
This chapter describes developments in digital and mixed-signal applications of superconducting electronics. In the class of mixed-signal circuits, the analog-to-digital converters are the most developed and promising circuits for many applications. Low-temperature superconductors such as Nb are the main superconductor materials for digital and mixed-signal circuits. In order to eliminate or at least significantly reduce the static power dissipation in RSFQ circuits, a number of different logic approaches have been proposed ranging from the simple reduction of the bias resistor resistance to its complete elimination. Contrary to predominantly sequential RSFQ-type circuits described above, RQL logic gates are combinational. To provide a sufficient flux bias signal to the next gate in presence of possible fabrication spread, one has to ensure adequate current flowing through the transformer. The largest superconducting random access memory was demonstrated only at 4 kbit per chip which was not sufficient for applications.