Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Journal of Quantum Electronics

Operation of an all-optical bistable device dependent upon incident and transmitted optical power

Ralph S. Jameson, Wen-Tserr-Lee

Published Jan 1, 1989• 3 citations
Publisher

Abstract

The authors describe the optically bistable operation of an all-optical nonlinear Fabry-Perot etalon (NLFP) in which the power-dependent cavity phase shift has a contribution dependent on the power incident on the cavity. When the contributions have the same parity, the optically-bistable behavior is essentially the same as that seen in the now standard bistable NLFP (counterclockwise hysteresis in transmission). For opposite parity there is a range of relative strengths for which bistable operation cannot be obtained, but, outside of that range, bistable behavior having clockwise hysteresis in transmission is possible. This latter bistable behavior is demonstrated, with the NLFP being a GaAlAs laser diode amplifier driven by a similar diode laser. Low-frequency modulation of the laser power by direct variation of the laser drive current produced a small shift in laser wavelength proportional to the laser power, providing the cavity phase shift term proportional to the incident power, while the nonlinear refractive index of the NLFP provided the phase shift proportional to the transmitted power.>

DOI
10.1109/3.16255

Related papers

Optical bistability using a Fabry–Perot semiconductor-laser amplifier with two holding beams

Hitoshi Kawaguchi, Kyo Inoue, Hiroyuki Tani

Bistable switching of an optical signal beam by a control beam with a different wavelength, using the nonlinearity of a Fabry-Perot semiconductor-laser amplifier, is reported for the first time to the authors' knowledge. Depending on the initial detuning of the optical signal beam, both normal (counterclockwise) and reverse (clockwise) hysteresis are theoretically and experimentally obtained in the signal output power as a function of the control input power.

Optics Letters•Jul 1, 1987•32 citations

Optical bistability in asymmetric Fabry–Perot laser-diode amplifiers

N. F. Mitchell, John C. Connolly, James O’Gorman +1 more

We present what is to our knowledge the first study of optical bistability in Fabry-Perot laser-diode amplifiers that have asymmetric facet reflectivities. When operated in reflection, the light input-light output characteristics exhibit a transition from counterclockwise to clockwise hysteresis by way of an X-shaped or butterfly hysteresis. This transition can be achieved by a change in either the device bias or the phase detuning of the incident light. Our results are in good agreement with calculation.

Optics Letters•Feb 15, 1994•28 citations

Reflective bistability in 1.55 μm laser diode amplifiers

Paradorn Pakdeevanich, M.J. Adams

Bistable laser amplifiers are attractive for potential application in optical switching because of very low input optical requirement, high extinction ratio and the presence of optical gain. Optical bistability (OB) arises from gain saturation and the associated nonlinear refraction combined with the effect of feedback in the laser cavity. We present the experimental results of bistable characteristics for the case of a 1.55 /spl mu/m symmetric Fabry-Perot (F-P) laser amplifier with uncoated facets. This paper reports a particularly rich variety of behaviour for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical input-output characteristic when the drive current or initial phase detuning is changed. The butterfly hysteresis loop is observed experimentally at optical input power as low as 260 /spl mu/W for a drive current equal to 90% of the lasing threshold. The dependence of the optical bistability on drive current, initial phase detuning and injected optical power has been investigated. In the bistable light output-initial phase detuning characteristic, the optimum frequency is shifted downward with an increase in the injected power or the drive current. All measurements are in good agreement with an analytical model.

•Jan 1, 1998•0 citations

Switching power dependence on detuning and current in bistable diode laser amplifiers

Zeqi Pan, Hongchin Lin, M. Dagenais

Measurements of the optical power required to switch on-and-off an optical bistable diode laser amplifier as a function of detuning and current from threshold are presented. Good quantitative agreement between the theory for a nonlinear Fabry–Perot and the experimental results are obtained. A linewidth enhancement factor of 3.1 and a value for the change of the refractive index versus carrier density of −1.8×10−20 cm3 are extracted from the measurements.

Applied Physics Letters•Feb 18, 1991•30 citations

Optical Bistability

Guang S. He

When the output parameter of an optical device could be a multivalued function of the input parameter, this device can be working in an optical bistable status. The most typical optical bistable device is a Fabry–Perot cavity containing a nonlinear optical medium, the refractive index of which depends on the light intensity. Upon the action of an intense input optical beam, the transmitted (or reflected) intensity of this device may exhibit a nonlinear response to the incident light intensity variation and, especially under appropriate working conditions, the characteristic output/input curve may manifest a single (or multiple) hysteresis loop(s). Such type of optical bistable device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element, depending on the chosen nonlinear medium and operation conditions.

Oxford University Press eBooks•Oct 30, 2014•1 citation

Optical bistability and X-shaped hysteresis in laser diode amplifiers

N. F. Mitchell, James O’Gorman, John Hegarty +1 more

Laser diode amplifiers exhibit optical bistability when biased just below lasing threshold, and have applications as optical memory elements and optical switches, due to their very low switching energy (fJ) and presence of optical gain. While LDAs operated in transmission have received much attention, the reflection mode of operation has been largely neglected. In this paper we present a detailed experimental and numerical investigation of Fabry Perot LDA (FP-LDA) behavior under light injection when operated in reflection. We observe transitions from anticlockwise to clockwise hysteresis with changing bias level or incident wavelength detuning. Moreover, we also report the first experimental observation of X-shaped (or butterfly hysteresis) in this system. Our results are in very good agreement with calculation.>

IEEE Lasers and Electro-Optics Society Annual Meeting (LEOS)•Dec 30, 2002•4 citations
The authors describe the optically bistable operation of an all-optical nonlinear Fabry-Perot etalon (NLFP) in which the power-dependent cavity phase shift has a contribution dependent on the power incident on the cavity. When the contributions have the same parity, the optically-bistable behavior is essentially the same as that seen in the now standard bistable NLFP (counterclockwise hysteresis in transmission). For opposite parity there is a range of relative strengths for which bistable operation cannot be obtained, but, outside of that range, bistable behavior having clockwise hysteresis in transmission is possible. This latter bistable behavior is demonstrated, with the NLFP being a GaAlAs laser diode amplifier driven by a similar diode laser. Low-frequency modulation of the laser power by direct variation of the laser drive current produced a small shift in laser wavelength proportional to the laser power, providing the cavity phase shift term proportional to the incident power, while the nonlinear refractive index of the NLFP provided the phase shift proportional to the transmitted power.>
We present what is to our knowledge the first study of optical bistability in Fabry-Perot laser-diode amplifiers that have asymmetric facet reflectivities. When operated in reflection, the light input-light output characteristics exhibit a transition from counterclockwise to clockwise hysteresis by way of an X-shaped or butterfly hysteresis. This transition can be achieved by a change in either the device bias or the phase detuning of the incident light. Our results are in good agreement with calculation.
Bistable laser amplifiers are attractive for potential application in optical switching because of very low input optical requirement, high extinction ratio and the presence of optical gain. Optical bistability (OB) arises from gain saturation and the associated nonlinear refraction combined with the effect of feedback in the laser cavity. We present the experimental results of bistable characteristics for the case of a 1.55 /spl mu/m symmetric Fabry-Perot (F-P) laser amplifier with uncoated facets. This paper reports a particularly rich variety of behaviour for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical input-output characteristic when the drive current or initial phase detuning is changed. The butterfly hysteresis loop is observed experimentally at optical input power as low as 260 /spl mu/W for a drive current equal to 90% of the lasing threshold. The dependence of the optical bistability on drive current, initial phase detuning and injected optical power has been investigated. In the bistable light output-initial phase detuning characteristic, the optimum frequency is shifted downward with an increase in the injected power or the drive current. All measurements are in good agreement with an analytical model.
When the output parameter of an optical device could be a multivalued function of the input parameter, this device can be working in an optical bistable status. The most typical optical bistable device is a Fabry–Perot cavity containing a nonlinear optical medium, the refractive index of which depends on the light intensity. Upon the action of an intense input optical beam, the transmitted (or reflected) intensity of this device may exhibit a nonlinear response to the incident light intensity variation and, especially under appropriate working conditions, the characteristic output/input curve may manifest a single (or multiple) hysteresis loop(s). Such type of optical bistable device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element, depending on the chosen nonlinear medium and operation conditions.
Laser diode amplifiers exhibit optical bistability when biased just below lasing threshold, and have applications as optical memory elements and optical switches, due to their very low switching energy (fJ) and presence of optical gain. While LDAs operated in transmission have received much attention, the reflection mode of operation has been largely neglected. In this paper we present a detailed experimental and numerical investigation of Fabry Perot LDA (FP-LDA) behavior under light injection when operated in reflection. We observe transitions from anticlockwise to clockwise hysteresis with changing bias level or incident wavelength detuning. Moreover, we also report the first experimental observation of X-shaped (or butterfly hysteresis) in this system. Our results are in very good agreement with calculation.>