Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Chinese Optics Letters

Spectral hole burning effects initiated by uniform signal intensities in a gain-flattened EDFA

Abdul Rahman Sarmani, S-J Sheih S-J Sheih, Faisal Rafiq Mahamd Adikan, M. A. Mahdi

Published Jan 1, 2011• 4 citations
Publisher

Abstract

Spectral hole burning (SHB) effects in a gain-flattened erbium-doped fiber amplifier (EDFA) are demonstrated to be significant in the presence of large signal power around the 1530-1532-nm wavelength range.These are the first effects reported in a setup employing equivalent power level distribution of 40 channels ranging from 1530 to 1561 nm.To explain this, the introduction of a new local population variable into the laser equation is required to support the original inversion ratio that is determined by the pump lasers.In the analysis section, spectroscopic parameters and high signal powers are considered to be other contributing parameters to the change in the gain characteristics.An improvement to this theoretical basis is suggested by implementing mathematical modeling to validate similarities between the gain shape of simulation to that obtained in the experiment.

DOI
10.3788/col201109.020603

Related papers

Dynamics of Spectral Hole Burning in EDFAs: Dependency on Pump Wavelength and Pump Power

Lutz Rapp, João M. Ferreira

Pump wavelength and pump power dependency of the dynamical response of spectral hole burning (SHB) in erbium-doped fiber amplifiers (EDFAs) is investigated. The experimental results show a clear dependency on pump wavelength also in the 1480-nm range. Similar to other effects in EDFAs affecting transient performance, dynamics of SHB speeds up with increasing pump power. We conclude that the pump has a significant contribution to SHB and has to be taken into account in numerical models for SHB.

IEEE Photonics Technology Letters•Jun 18, 2010•10 citations

Pump wavelength-dependent spectral-hole burning in EDFAs

Michael J. Yadlowsky

Gain-difference spectra are used to show that 980-nm band pump wavelength changes can significantly effect spectral-hole burning (SHB) in erbium-doped fiber amplifiers (EDFAs). Gain measurements made using a number of different signal and pump wavelengths help to characterize the underlying inhomogeneous spectral properties of EDFAs and a framework for modeling these effects is presented. Despite the difficulty of obtaining the needed subpopulation specific cross section spectra, this model can be used to explain seemingly anomalous changes in the gain spectra of EDFA as a result of changes in signal or pump wavelength.

Journal of Lightwave Technology•Jan 1, 1999•14 citations

Spectral hole burning in erbium-doped fiber amplifiers

Maxim A. Bolshtyansky

A new theoretical/numerical model of the spectral hole burning (SHB) effect in erbium-doped fiber amplifiers (EDFAs) is suggested. A new measurement technique for SHB measurement is developed. Experiments are conducted to identify the particular mechanism of SHB. A computer simulation program is developed using this approach. The shape and depth of the spectral hole are in accordance with the suggested theory.

Journal of Lightwave Technology•Apr 1, 2003•63 citations

Room temperature spectral hole-burning in erbium-doped fiber amplifiers

A.K. Srivastava, J.L. Zyskind, James W. Sulhoff +2 more

Summary form only given. In this paper we report the first room temperature measurements of spectral hole-burning depths and widths of an Er-doped fiber amplifier (EDFA). The alumino-germano-silicate EDFA was pumped at 1480 nm and had a small signal gain of 25 dB at 1551 nm. Spectral gain measurements were carried out in the range 1535-1570 nm using a lock-in technique and spectral subtraction for accurate determination of SHB properties.

Optical Fiber Communication Conference•Jan 1, 1996•39 citations

Distributed gain and spectral gain-saturation effects in erbium doped fibers

Waldemar Roberto Ruziscka, A.O. Dal Forno, R. Passy +2 more

Distributed gain and spectral gain-saturation effects of erbium-doped fiber amplifier (EDFA) were measured using a coherent reflectrometry technique. We find that the spectral performance can be improved if the gain needs are relaxed. A hole in the spectral dependence of the gain depletion was also observed, which could be related to the Spectral Hole Burning (SHB) phenomenon.

SBMO/IEEE MTT-S International Microwave and Optoelectronics Conference (IMOC)•Jan 22, 2003•0 citations

Observation of Replica Holes in Erbium Doped Silica Fiber

Thiago P. Mayer Alegre, Gustavo S. Wiederhecker, Hugo L. Fragnito

Abstract We observed for the first time to our knowledge the presence of replica holes in the fluorescencespectrum of EDFA. Saturating the Er 3+ transition at a single wavelength we noticed theappearance of spectral holes in the ASE other than the usual one around the saturating laser. Wequalitatively explain the effect and confront the experimental results with the homogeneouslybroadened model. Introduction One of the limiting factors to state-of-the-art DWDM systems is the effect of Spectral Hole Burning (SHB) inErbium Doped Fiber Amplifiers (EDFAs). It has been already observed that the presence of a saturating signal ina given wavelength induces a hole around the signal in the gain and Amplified Spontaneous Emission (ASE)spectra [1],[2]. These holes in EDFAs are typically between 2 and 8 nm width, which is enough to degrade theneighboring channels. The SHB effect is due to the inhomogeneous broadening of the Er 3+ transitions, causedby site-to-site variations of the local electric field in the silica based host, which induces different ions laser linesproperties.This work shows the existence of spectral holes burned at wavelengths far from the saturating laserline, called Spectral Replica Holes (SRHs). The physical background that explains SRHs is based on theinhomogeneously broadened two-level Stark Splitted

•Jan 1, 2003•1 citation
Spectral hole burning (SHB) effects in a gain-flattened erbium-doped fiber amplifier (EDFA) are demonstrated to be significant in the presence of large signal power around the 1530-1532-nm wavelength range.These are the first effects reported in a setup employing equivalent power level distribution of 40 channels ranging from 1530 to 1561 nm.To explain this, the introduction of a new local population variable into the laser equation is required to support the original inversion ratio that is determined by the pump lasers.In the analysis section, spectroscopic parameters and high signal powers are considered to be other contributing parameters to the change in the gain characteristics.An improvement to this theoretical basis is suggested by implementing mathematical modeling to validate similarities between the gain shape of simulation to that obtained in the experiment.
Gain-difference spectra are used to show that 980-nm band pump wavelength changes can significantly effect spectral-hole burning (SHB) in erbium-doped fiber amplifiers (EDFAs). Gain measurements made using a number of different signal and pump wavelengths help to characterize the underlying inhomogeneous spectral properties of EDFAs and a framework for modeling these effects is presented. Despite the difficulty of obtaining the needed subpopulation specific cross section spectra, this model can be used to explain seemingly anomalous changes in the gain spectra of EDFA as a result of changes in signal or pump wavelength.
Abstract We observed for the first time to our knowledge the presence of replica holes in the fluorescencespectrum of EDFA. Saturating the Er 3+ transition at a single wavelength we noticed theappearance of spectral holes in the ASE other than the usual one around the saturating laser. Wequalitatively explain the effect and confront the experimental results with the homogeneouslybroadened model. Introduction One of the limiting factors to state-of-the-art DWDM systems is the effect of Spectral Hole Burning (SHB) inErbium Doped Fiber Amplifiers (EDFAs). It has been already observed that the presence of a saturating signal ina given wavelength induces a hole around the signal in the gain and Amplified Spontaneous Emission (ASE)spectra [1],[2]. These holes in EDFAs are typically between 2 and 8 nm width, which is enough to degrade theneighboring channels. The SHB effect is due to the inhomogeneous broadening of the Er 3+ transitions, causedby site-to-site variations of the local electric field in the silica based host, which induces different ions laser linesproperties.This work shows the existence of spectral holes burned at wavelengths far from the saturating laserline, called Spectral Replica Holes (SRHs). The physical background that explains SRHs is based on theinhomogeneously broadened two-level Stark Splitted