Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Asia-Pacific Microwave Conference (APMC)

600-696GHz Heterodyne Receiver with Fixed-Tuned SIS Mixer and Martin-Puplett LO/RF Diplexer

Yuh-Jing Hwang, Ming-Jye Wang, Homin Jiang, Ming‐Tang Chen, Sheng‐Cai Shi, Qijun Yao

Published Mar 22, 2006• 1 citation
Publisher

Abstract

A heterodyne receiver equipped with fixed-tuned superconductor-insulator-superconductor (SIS) mixer is developed and characterized. A Martin-Puplett interferometer is used in the receiver as diplexer to combine the RF/LO signal. The receiver noise measurement indicates the lowest receiver noise temperature including the optical loss of the MPI is as low as 250K. The receiver noise temperature is below 400K in the IF center frequency and below 500K over whole IF passband for LO frequency tuned between 624-696GHz.

DOI
10.1109/apmc.2005.1606238

Related papers

A Low-noise Balanced SIS Mixer for the 790-950 GHz Band

Takafumi Kojima, Yasunori FUJII, Yoshinori Uzawa

We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.

TEION KOGAKU (Journal of Cryogenics and Superconductivity Society of Japan)•Jan 1, 2014•2 citations

Fabrication and characterization of a 600-720 GHz resonant distributed SIS junction for fixed-tuned waveguide receiver

T. Matsunaga, Edward Tong, R. Blundell +1 more

The non-linear quasiparticle tunnel current flowing in a distributed superconductor-insulator-superconductor (SIS) transmission line resonator has been exploited in a low-noise heterodyne fixed-tuned waveguide receiver in the 600-720 GHz band. The mixer employs two 1.4 /spl mu/m wide half-wave or full-wave distributed SIS long junctions that are connected in series. These devices have been fabricated with optical lithography. Noise temperatures of 160-240 K have been measured at around 600 GHz. However, the achieved RF bandwidth is only about 5 % and the center frequency of the resonance is also shifted towards lower end of the target frequencies.

Asia-Pacific Microwave Conference (APMC)•Nov 13, 2002•0 citations

Performance of an SIS receiver over 460 GHz to 640 GHz using submicron Nb junctions with integrated RF tuning circuits

Pascal Febvre

The most sensitive heterodyne receivers used formillimeter wave and submillimeter wave radioastronomyemploy superconductor-insulator-superconductor (SIS)tunnel junctions as the nonlinear mixing element. Goodperformance has recently been reported for SIS junctionsused in planar mixer circuits and waveguide mixers fromabout 300 GHz to 500 GHz. We have developed asubmillimeter wave SIS heterodyne receiver for observingimportant rotational transitions of molecules in theinterstellar medium near 550 GHz and 630 GHz. Thisreceiver is based on a waveguide mixer with an adjustablebackshort and E-plane tuner [1]. The mixer uses a highcurrent density, 0.25 gm2 Nb-A1Ox-Nb tunnel junctiondefined by electron beam lithography [2]. The capacitanceof the junction is compensated with an integrated RFsuperconductive microstrip tuning circuit. The receiverperformance has been measured over the frequency range460 GHz to 640 GHz. DSB receiver noise temperatures aslow as 200 ± 17 K at 540 GHz and 362 ± 33 K at626 GHz have been obtained. In addition, negativedifferential resistance has been observed in the DC I-Vcurve at frequencies around 491 GHz. These results indicatethat the superconductive Nb microstrip transmission linesused in the tuning circuits are low-loss and perform well upto at least 90% of the superconductor energy gap frequency.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Aug 30, 1993•0 citations

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations

Performance Characterization of a 600-700 GHz SIS Mixer

M. J. Wang, Rey Chin, Wenlei Shan +4 more

A 600-700GHz SIS mixer with the twin-junction tuning circuit has been designed and fabricated [1] The surface impedance of thin-film superconducting microstrip lines, based on Mattis-Bardeen theory [2], is included in the optimization of RF impedance matching. The receiver noise temperature measured in the frequency range of 630-660GHz is below 200K and the lowest receiver noise temperature of 181K is achieved at 656GHz. The FTS response of the SIS mixer shows a good RF coupling from 600GHz to 700GHz. Both the noise performance and the FTS response can be quantitatively described by numerical results using the quantum theory of mixing. Some detail considerations on the mixer model calculation, such as spreading inductance around the junction tuning structure and mixer's embedding impedance, are discussed. Introduction Nb-based superconductor-insulator-superconductor (SIS) mixers have been used very successfully in sub-mm wavelength detection. Their receiver noise temperature has reached to three times the quantum limit, —3 hfrkB, below the junction's gap frequency. However, at high frequency bands, Nb SIS mixers need to be designed carefully because the photon energy is close to or higher than the gap energy of Nb, A-1.4meV. When the frequency band covers the gap frequency of Nb, —670GHz, the RF loss of Nb superconducting transmission lines increases dramatically and the surface impedance has strong frequency dependence. Usually, the RF properties of a superconducting transmission line can be described by the Mattis-Bardeen theory [2] in good accuracy. From results reported so far [4-9], the best receiver noise temperature is close to 5 hi7kB in the band of 600-700GHz. Despite of the input loss contributed by the experimental setup, some other properties of SIS mixers should be taken into account. In this paper, we characterize the performance of a 600-700GHz mixer by comparing the experimental and simulated results.

Softwaretechnik-Trends•Mar 1, 2002•1 citation

A 547 GHz SIS receiver employing a submicron Nb junction with an integrated matching circuit

Pascal Febvre, William R. McGrath, P. D. Batelaan +4 more

A heterodyne receiver using an SIS (superconductor-insulator-superconductor) waveguide mixer with two mechanical tuners has been built and characterized over the frequency range of 460 GHz to 630 GHz. This receiver is designed for radioastronomy applications. The mixer uses high-current-density, 0.25- mu m/sup 2/, Nb/AlO/sub x//Nb SIS tunnel junctions with integrated superconductive RF circuits to tune the junction capacitance. A DSB (double sideband) receiver noise temperature as low as 200+or-17 K has been obtained at 540 GHz. In addition, negative differential resistance has been observed in the DC I-V (current-voltage) curve at 487-491 GHz.>

IEEE MTT-S International Microwave Symposium digest•Dec 30, 2002•4 citations
A heterodyne receiver equipped with fixed-tuned superconductor-insulator-superconductor (SIS) mixer is developed and characterized. A Martin-Puplett interferometer is used in the receiver as diplexer to combine the RF/LO signal. The receiver noise measurement indicates the lowest receiver noise temperature including the optical loss of the MPI is as low as 250K. The receiver noise temperature is below 400K in the IF center frequency and below 500K over whole IF passband for LO frequency tuned between 624-696GHz.
We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.
The non-linear quasiparticle tunnel current flowing in a distributed superconductor-insulator-superconductor (SIS) transmission line resonator has been exploited in a low-noise heterodyne fixed-tuned waveguide receiver in the 600-720 GHz band. The mixer employs two 1.4 /spl mu/m wide half-wave or full-wave distributed SIS long junctions that are connected in series. These devices have been fabricated with optical lithography. Noise temperatures of 160-240 K have been measured at around 600 GHz. However, the achieved RF bandwidth is only about 5 % and the center frequency of the resonance is also shifted towards lower end of the target frequencies.
The most sensitive heterodyne receivers used formillimeter wave and submillimeter wave radioastronomyemploy superconductor-insulator-superconductor (SIS)tunnel junctions as the nonlinear mixing element. Goodperformance has recently been reported for SIS junctionsused in planar mixer circuits and waveguide mixers fromabout 300 GHz to 500 GHz. We have developed asubmillimeter wave SIS heterodyne receiver for observingimportant rotational transitions of molecules in theinterstellar medium near 550 GHz and 630 GHz. Thisreceiver is based on a waveguide mixer with an adjustablebackshort and E-plane tuner [1]. The mixer uses a highcurrent density, 0.25 gm2 Nb-A1Ox-Nb tunnel junctiondefined by electron beam lithography [2]. The capacitanceof the junction is compensated with an integrated RFsuperconductive microstrip tuning circuit. The receiverperformance has been measured over the frequency range460 GHz to 640 GHz. DSB receiver noise temperatures aslow as 200 ± 17 K at 540 GHz and 362 ± 33 K at626 GHz have been obtained. In addition, negativedifferential resistance has been observed in the DC I-Vcurve at frequencies around 491 GHz. These results indicatethat the superconductive Nb microstrip transmission linesused in the tuning circuits are low-loss and perform well upto at least 90% of the superconductor energy gap frequency.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
A 600-700GHz SIS mixer with the twin-junction tuning circuit has been designed and fabricated [1] The surface impedance of thin-film superconducting microstrip lines, based on Mattis-Bardeen theory [2], is included in the optimization of RF impedance matching. The receiver noise temperature measured in the frequency range of 630-660GHz is below 200K and the lowest receiver noise temperature of 181K is achieved at 656GHz. The FTS response of the SIS mixer shows a good RF coupling from 600GHz to 700GHz. Both the noise performance and the FTS response can be quantitatively described by numerical results using the quantum theory of mixing. Some detail considerations on the mixer model calculation, such as spreading inductance around the junction tuning structure and mixer's embedding impedance, are discussed. Introduction Nb-based superconductor-insulator-superconductor (SIS) mixers have been used very successfully in sub-mm wavelength detection. Their receiver noise temperature has reached to three times the quantum limit, —3 hfrkB, below the junction's gap frequency. However, at high frequency bands, Nb SIS mixers need to be designed carefully because the photon energy is close to or higher than the gap energy of Nb, A-1.4meV. When the frequency band covers the gap frequency of Nb, —670GHz, the RF loss of Nb superconducting transmission lines increases dramatically and the surface impedance has strong frequency dependence. Usually, the RF properties of a superconducting transmission line can be described by the Mattis-Bardeen theory [2] in good accuracy. From results reported so far [4-9], the best receiver noise temperature is close to 5 hi7kB in the band of 600-700GHz. Despite of the input loss contributed by the experimental setup, some other properties of SIS mixers should be taken into account. In this paper, we characterize the performance of a 600-700GHz mixer by comparing the experimental and simulated results.
A heterodyne receiver using an SIS (superconductor-insulator-superconductor) waveguide mixer with two mechanical tuners has been built and characterized over the frequency range of 460 GHz to 630 GHz. This receiver is designed for radioastronomy applications. The mixer uses high-current-density, 0.25- mu m/sup 2/, Nb/AlO/sub x//Nb SIS tunnel junctions with integrated superconductive RF circuits to tune the junction capacitance. A DSB (double sideband) receiver noise temperature as low as 200+or-17 K has been obtained at 540 GHz. In addition, negative differential resistance has been observed in the DC I-V (current-voltage) curve at 487-491 GHz.>