Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Design and Operation of HTS 1:2 Switch Circuit

Koji Tsubone, H. Wakana, Yoshinobu Tarutani, Seiji Adachi, Yoshihiro Ishimaru, Kohei Nakayama, Yasuo Oshikubo, Osami Horibe, K. Tanabe

Published Jun 1, 2007• 2 citations
Publisher

Abstract

A Single flux quantum (SFQ) one-to-two (1:2) switch circuit was designed and fabricated by using YBa2Cu3O7-deltaramp-edge junction technology, and the logic operations were investigated. The circuit parameters were optimized by taking account of an Icspread and a global Icshift due to an operation temperature change and insufficient run-to-run reproducibility. In addition, the influence of the parasitic inductance on Icmargins was investigated by simulation. A test circuit including the 1:2 switch circuit was successfully operated at temperatures of 52 K-60 K. Finite dc supply current margins obtained at temperatures of 55 K-60 K were comparable to those determined by the simulation.

DOI
10.1109/tasc.2007.898634

Related papers

Logic Operation of HTS SFQ Logic Family

Koji Tsubone, Y. Tarutani, H. Wakana +2 more

A high-Tcsuperconducting (HTS) single-flux-quantum (SFQ) logic family including an and gate, an or gate, and an inverter was designed. The circuit parameters were optimized for a Josephson junction's critical current density, which may change due to a temperature change or insufficient run-to-run reproducibility of the fabrication process. New circuit design layout rules were implemented to improve Icx uniformity. As a result, all circuits were successfully tested and show at least plusmn40% critical current density operational margins. An effect of the parasitic capacitance formed by a junction electrode and a ground plane on the operating margins of the and gate was investigated by numerical simulation. Test circuits were fabricated using YBa2Cu3O7-deltaramp-edge junction technology and were operated at temperatures higher than 30 K. Bias current margins were also measured, and they found to be close to the simulated ones.

IEEE Transactions on Applied Superconductivity•Jul 15, 2009•2 citations

Design and Operation of HTS SFQ Circuit Elements

Koji Tsubone, H. Wakana, Y. Tarutani +3 more

Single flux quantum (SFQ) circuit elements have been designed and fabricated using the YBa 2 Cu 3 O 7-δ ramp-edge junction technology. Logic operations of SFQ circuit elements, such as a toggle flip-flop (T-FF), a set-reset flip-flop (RS-FF), and a 96-junction Josephson transmission line (JTL), were successfully demonstrated, and dc supply current margins were confirmed up to temperatures higher than 30 K. The circuit layout was improved in order to suppress the critical current (I c ) spread that appears during the junction fabrication procedure. By employing the new circuit layout rule, correct operations at temperatures from 27 K to 34 K with dc supply current margins wider than ±7% were confirmed for the T-FF with a single output. Moreover, the maximum operating frequencies of T-FFs were measured to be 360GHz at 4.2K and 210GHz at 41K, which are substantially higher than the values for the circuits with the conventional layout. According to the simulation result, the maximum operating frequency at 40 K was expected to be approximately 50% of the characteristic frequency at a bit error rate (BER) less than 10 -6 .

IEICE Transactions on Electronics•Mar 1, 2007•4 citations

Operation of HTS Toggle-Flip-Flop Circuit With Improved Layout Design

Koji Tsubone, H. Wakana, Yoshinobu Tarutani +4 more

Toggle-flip-flop (T-FF) is one of the most important high-Tcsuperconducting single-flux quantum (HTS SFQ) circuit components and has been designed and fabricated by using YBa2Cu3O7-deltaramp-edge junction technology. The circuit layout of the T-FF was improved to suppress the junction critical current (Ic) spread in the circuit. Test circuits, which include a T-FF with a single output for evaluating the logic operation and measuring the operating frequency, were fabricated and their operation characteristics were investigated. The T-FF circuit with a single output was successfully operated and finite direct current (dc) supply current margins were obtained at temperatures from 27 to 34 K. Moreover, the maximum operating frequency of the T-FF was estimated to be 360 GHz at 4.2 K and 114 GHz at 41 K. In addition, reduction of dc supply current margins due to thermal noise was also investigated. According to the numerical simulation in which parasitic inductances were taken into account, the narrowest margin in the T-FF circuit wider than plusmn10% was maintained with a bit-error rate (BER) of 10-6up to 40 K

IEEE Transactions on Applied Superconductivity•Dec 1, 2006•15 citations

Logic Operation of SFQ Circuit Elements Made of YBCO Junctions

Y. Tarutani, Koji Tsubone, H. Wakana +6 more

YBa2Cu3O7-x(YBCO) ramp-edge junction technologies have been developed for fabricating high-operating-temperature SFQ(Single Flux Quantum) circuits. The Ic(critical current) spread that is the key parameter for integrating junctions could be decreased to 8% for a 1000-junction array that was formed on a groundplane. The background technologies that enabled this uniform junction characteristic are precise control of the counter-electrode deposition-conditions and deposition of the extremely smooth multiplayer that showed the roughness as small as 2 nm. Based upon these ramp-edge junction technologies, oxide SFQ-circuit-elements were fabricated and their logic operations were investigated. SFQ circuit elements such as a confluence buffer, a set-reset flipflop, and a toggle flipflop have been fabricated and their logic operations were measured by using an SFQ-dc converter. Both toggle flipflops that have one output and two outputs have been fabricated. These circuits could be operated up to the temperature of near 60 K under finite operating margins. These experimental results enable us to further develop fuctional and much more integrated SFQ circuits.

Advances in science and technology•Oct 1, 2006•0 citations

High-Temperature Operation of Oxide SFQ-Circuit-Elements

Koji Tsubone, H. Wakana, Yoshihiro Ishimaru +4 more

Single flux quantum (SFQ) circuit components such as an SFQ-dc converter and a confluence buffer have been fabricated by using an YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// ramp-edge junction technology and their logic operations at temperatures up to near 60 K were investigated. The SFQ-dc converter was correctly operated in a wide temperature range from 4.2 K to 56 K and found to be useful for detecting output signals from other SFQ circuit components at any operating temperatures. The basic function that a signal from either of two input Josephson transmission lines (JTLs) was transmitted to an output JTL was confirmed for the confluence buffer and finite operating margins were obtained at temperatures from 42 K to 61 K. The narrowest margin of dc supply current obtained at temperatures from 55 K to 60 K was /spl plusmn/20% and was consistent with the simulation. Margin reduction due to thermal noise was also evaluated. According to the analytical calculation, the operating margin to keep the bit-error rate less than 10/sup -5/ was as large as /spl plusmn/20% even at 50 K when the value of junction critical-current I/sub c/ was kept near 0.4 mA.

IEEE Transactions on Applied Superconductivity•Dec 1, 2005•16 citations

Limitations on HTS single flux quantum logic

J.S. Satchell

There is widespread interest in transferring Single Flux Quantum (SFQ) logic from niobium technology to a suitable HTS technology. The higher operating temperature results in increased noise and associated errors. We have developed numerical methods to study noise induced errors and how they depend on circuit parameters. A simple picture holds for all the circuits studied to date. The error probability shows an error function (integrated Gaussian) distribution. The width of the distribution is circuit dependent, but is 1 to 4 times the noise contribution of a single junction, and the noise free (deterministic) margin corresponds to the point where the error probability is 0.5. The distributions are frequently asymmetric, and minimum error rate does not occur for a design centered between the deterministic margins. A stochastic optimizer has been developed that allows us reoptimize circuits for conditions when noise induced margin narrowing is important. We have used this to study the influence of layout induced stray inductance on the feasibility of HTS circuits using the T flip-flop as an example. Stray inductance appears to be as important as junction reproducibility, and significant improvements are needed to allow high operating temperatures.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•23 citations
A Single flux quantum (SFQ) one-to-two (1:2) switch circuit was designed and fabricated by using YBa2Cu3O7-deltaramp-edge junction technology, and the logic operations were investigated. The circuit parameters were optimized by taking account of an Icspread and a global Icshift due to an operation temperature change and insufficient run-to-run reproducibility. In addition, the influence of the parasitic inductance on Icmargins was investigated by simulation. A test circuit including the 1:2 switch circuit was successfully operated at temperatures of 52 K-60 K. Finite dc supply current margins obtained at temperatures of 55 K-60 K were comparable to those determined by the simulation.
A high-Tcsuperconducting (HTS) single-flux-quantum (SFQ) logic family including an and gate, an or gate, and an inverter was designed. The circuit parameters were optimized for a Josephson junction's critical current density, which may change due to a temperature change or insufficient run-to-run reproducibility of the fabrication process. New circuit design layout rules were implemented to improve Icx uniformity. As a result, all circuits were successfully tested and show at least plusmn40% critical current density operational margins. An effect of the parasitic capacitance formed by a junction electrode and a ground plane on the operating margins of the and gate was investigated by numerical simulation. Test circuits were fabricated using YBa2Cu3O7-deltaramp-edge junction technology and were operated at temperatures higher than 30 K. Bias current margins were also measured, and they found to be close to the simulated ones.
Single flux quantum (SFQ) circuit elements have been designed and fabricated using the YBa 2 Cu 3 O 7-δ ramp-edge junction technology. Logic operations of SFQ circuit elements, such as a toggle flip-flop (T-FF), a set-reset flip-flop (RS-FF), and a 96-junction Josephson transmission line (JTL), were successfully demonstrated, and dc supply current margins were confirmed up to temperatures higher than 30 K. The circuit layout was improved in order to suppress the critical current (I c ) spread that appears during the junction fabrication procedure. By employing the new circuit layout rule, correct operations at temperatures from 27 K to 34 K with dc supply current margins wider than ±7% were confirmed for the T-FF with a single output. Moreover, the maximum operating frequencies of T-FFs were measured to be 360GHz at 4.2K and 210GHz at 41K, which are substantially higher than the values for the circuits with the conventional layout. According to the simulation result, the maximum operating frequency at 40 K was expected to be approximately 50% of the characteristic frequency at a bit error rate (BER) less than 10 -6 .
Toggle-flip-flop (T-FF) is one of the most important high-Tcsuperconducting single-flux quantum (HTS SFQ) circuit components and has been designed and fabricated by using YBa2Cu3O7-deltaramp-edge junction technology. The circuit layout of the T-FF was improved to suppress the junction critical current (Ic) spread in the circuit. Test circuits, which include a T-FF with a single output for evaluating the logic operation and measuring the operating frequency, were fabricated and their operation characteristics were investigated. The T-FF circuit with a single output was successfully operated and finite direct current (dc) supply current margins were obtained at temperatures from 27 to 34 K. Moreover, the maximum operating frequency of the T-FF was estimated to be 360 GHz at 4.2 K and 114 GHz at 41 K. In addition, reduction of dc supply current margins due to thermal noise was also investigated. According to the numerical simulation in which parasitic inductances were taken into account, the narrowest margin in the T-FF circuit wider than plusmn10% was maintained with a bit-error rate (BER) of 10-6up to 40 K
YBa2Cu3O7-x(YBCO) ramp-edge junction technologies have been developed for fabricating high-operating-temperature SFQ(Single Flux Quantum) circuits. The Ic(critical current) spread that is the key parameter for integrating junctions could be decreased to 8% for a 1000-junction array that was formed on a groundplane. The background technologies that enabled this uniform junction characteristic are precise control of the counter-electrode deposition-conditions and deposition of the extremely smooth multiplayer that showed the roughness as small as 2 nm. Based upon these ramp-edge junction technologies, oxide SFQ-circuit-elements were fabricated and their logic operations were investigated. SFQ circuit elements such as a confluence buffer, a set-reset flipflop, and a toggle flipflop have been fabricated and their logic operations were measured by using an SFQ-dc converter. Both toggle flipflops that have one output and two outputs have been fabricated. These circuits could be operated up to the temperature of near 60 K under finite operating margins. These experimental results enable us to further develop fuctional and much more integrated SFQ circuits.
Single flux quantum (SFQ) circuit components such as an SFQ-dc converter and a confluence buffer have been fabricated by using an YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// ramp-edge junction technology and their logic operations at temperatures up to near 60 K were investigated. The SFQ-dc converter was correctly operated in a wide temperature range from 4.2 K to 56 K and found to be useful for detecting output signals from other SFQ circuit components at any operating temperatures. The basic function that a signal from either of two input Josephson transmission lines (JTLs) was transmitted to an output JTL was confirmed for the confluence buffer and finite operating margins were obtained at temperatures from 42 K to 61 K. The narrowest margin of dc supply current obtained at temperatures from 55 K to 60 K was /spl plusmn/20% and was consistent with the simulation. Margin reduction due to thermal noise was also evaluated. According to the analytical calculation, the operating margin to keep the bit-error rate less than 10/sup -5/ was as large as /spl plusmn/20% even at 50 K when the value of junction critical-current I/sub c/ was kept near 0.4 mA.
There is widespread interest in transferring Single Flux Quantum (SFQ) logic from niobium technology to a suitable HTS technology. The higher operating temperature results in increased noise and associated errors. We have developed numerical methods to study noise induced errors and how they depend on circuit parameters. A simple picture holds for all the circuits studied to date. The error probability shows an error function (integrated Gaussian) distribution. The width of the distribution is circuit dependent, but is 1 to 4 times the noise contribution of a single junction, and the noise free (deterministic) margin corresponds to the point where the error probability is 0.5. The distributions are frequently asymmetric, and minimum error rate does not occur for a design centered between the deterministic margins. A stochastic optimizer has been developed that allows us reoptimize circuits for conditions when noise induced margin narrowing is important. We have used this to study the influence of layout induced stray inductance on the feasibility of HTS circuits using the T flip-flop as an example. Stray inductance appears to be as important as junction reproducibility, and significant improvements are needed to allow high operating temperatures.