Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

A New Design Methodology for Single-Flux-Quantum (SFQ) Logic Circuits Using Passive-Transmission-Line (PTL) Wiring

Y.. Kameda, Shinichi Yorozu, Y. Hashimoto

Published Jun 1, 2007• 52 citations
Publisher

Abstract

The introduction of passive-transmission-line (PTL) wiring to large-scale SFQ logic circuits offers several advantages over traditional Josephson-transmission-line (JTL) wiring, such as smaller wiring area, less delay, lower power consumption, and more freedom in routing. PTL wiring can drastically change the style of designing SFQ logic circuits. We propose a new methodology for designing large-scale SFQ circuits using PTL wiring. Aiming at generalizing SFQ circuit design, we chose synchronous clocking. We developed a placer that was suitable for SFQ circuit design to assist us with the new design methodology. The placer first synthesizes an H-tree clock distribution network, placing SFQ pulse splitter cells at each branch. It then places logic cells to minimize the maximum length of data PTL wires, aiming at higher operating speeds. Finally, a router completes the PTL wiring. To evaluate the design methodology we designed an 8-bit general purpose RISC processor. Within twelve hours, we obtained a 15-mm-square SFQ circuit that could operate up to 27.6 GHz. We adopted an advanced Nb process, which was characterized by a critical current density of 10 kA/cm2, two 5-mum-wide PTL wiring layers, and a minimum cell size of 30 mum times 30 mum. The circuit consisted of about 20,000 logic cells, which approximated more than 400,000 Josephson junctions including splitters to distribute the clock signal.

DOI
10.1109/tasc.2007.898718

Related papers

Design and Investigation of Gate-to-Gate Passive Interconnections for SFQ Logic Circuits

Y. Hashimoto, Shinichi Yorozu, Y. Kameda +3 more

We have developed a method of designing single-flux-quantum (SFQ) logic circuits with passive gate-to-gate interconnections. Based on our method, we designed a 2/spl times/2 switch in which all the interconnections are implemented with passive transmission lines (PTLs) while short Josephson transmission line (JTL) segments are used only to adjust the signal timings. Compared with an identical switch using JTL interconnections, the switch using PTL interconnections has 45% fewer wiring junctions and requires 48% less wiring power current. The switch operated at 40 GHz with a bias margin of /spl plusmn/9.5%.

IEEE Transactions on Applied Superconductivity•Sep 1, 2005•19 citations

A design approach to passive interconnects for single flux quantum logic circuits

Y. Hashimoto, Shinichi Yorozu, Y. Kameda +1 more

We developed a design approach for interface circuits to connect Single Flux Quantum (SFQ) cells by using passive transmission lines (PTL's). In the approach, an interface circuit between a PTL and JTL is optimized to obtain a standard interface circuit, and then, modifications are made to previously designed SFQ cells and the standard interface circuit to connect the SFQ cells by using PTL's. The key point is the use of approximately the same interface circuit with every SFQ cell to maintain the matching condition between the interface circuit and the PTL's. Based on this approach, we designed an interface circuit and a test circuit composed of two D-flip-flops connected using 2-mm-long PTL's via the interface circuits. The impedance of the PTL was 2 /spl Omega/. We achieved high-speed operation of the test circuit up to 35 GHz with a bias margin of -15/+30%.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•53 citations

Interconnect Routing for Large-Scale RSFQ Circuits

Tahereh Jabbari, Gleb Krylov, Stephen R. Whiteley +3 more

The increasing complexity of modern rapid single flux quantum (RSFQ) circuits has made on-chip signal routing, an issue of growing importance. In this paper, several methods for routing large-scale RSFQ circuits are described, and a process is presented for determining when to use passive microstrip transmission lines (PTL) and active Josephson transmission lines (JTL). The effect of the size of the JTL inductor and Josephson junctions on the length of a JTL chain for a target delay is also discussed. The dependence of the JTL inductance on the physical layout is evaluated, and the effects of the primary PTL parameters on delay are characterized. A novel PTL driver and receiver configuration is also proposed. Tradeoffs among the number of JJs, inductance, and length of a PTL stripline in the receiver and driver circuits are reported. The energy dissipation is evaluated for two different interconnects. A tradeoff between the proposed PTL circuits and an optimized JTL in terms of energy dissipation and delay is discussed. Guidelines for choosing the optimal element values are determined, and a simulated bias margin of ±29% for the bias current of the proposed receiver operating at 20 GHz in a 10 kA/cm2technology for a 1-mm transmission line is achieved. Summarizing, guidelines and design tradeoffs appropriate for automated layout and synthesis are provided for driving long interconnect in SFQ VLSI circuits.

IEEE Transactions on Applied Superconductivity•Mar 4, 2019•88 citations

A Layout Design Flow for RSFQ Circuits Based on Cell Clustering and Mixed Wiring of JTLs and PTLs

Takashi Dejima, Kazuyoshi Takagi, Naofumi Takagi

An automated layout design flow for rapid single-flux-quantum circuits is proposed in this article. In order to realize small circuit area and low latency, both Josephson transmission lines (JTLs) and passive transmission lines (PTLs) are used for interconnects. Placement and routing are performed considering effective use of JTLs and PTLs. Logic cells are grouped into clusters, and JTLs are used inside clusters. PTLs are used among clusters. The placement process is composed of three steps: first, cell clustering, second, cell placement and JTL routing in each cluster, and third, cluster placement. After the placement process, routing among clusters are performed using PTLs. We applied the proposed design flow to sample circuits with several hundreds of gates. Though the circuit area is not fully optimized, the latency of the circuits designed by the proposed design flow are lower than those of the circuits designed manually.

IEEE Transactions on Applied Superconductivity•Aug 7, 2020•4 citations

Optimization of Passive Transmission Lines for Single Flux Quantum Circuits

Benjamin Chonigman, Ashish Shukla, Mustapha Habib +6 more

Passive transmission lines (PTLs) provide an energy-efficient means of transporting pulsed single flux quantum (SFQ) signals between logic gates and blocks on a chip, or even between chips through a multi-chip module carrier. Although functional up to 70 GHz, our previous designs manifested sharp, length-dependent resonances resulting in diminished operating margins. These are particularly inconvenient since the resonant length is about 1 mm at 40–50 GHz, where most SFQ circuits currently function. To avoid the need to keep the PTLs < 1 mm in length, we have optimized the PTL driver-receiver pairs to sufficiently suppress these resonances; this helps facilitate the use of automated routing tools. We present experimental results, in the 10-70 GHz frequency range, for different driver-receiver pairs designed for PTLs in our dual RSFQ-ERSFQ cell library. This cell library, targeting MIT Lincoln Laboratory's SFQ5ee fabrication process, uses PTLs with two types of ground plane configuration. The first variant has signal in M1 and/or M3 with symmetrical ground planes in M0, M2 and/or M2, M4 respectively. The second variant has signal in M2 and/or M3 with asymmetrical ground planes in M1 and M4. We also present a comparison with wider, 4 Ω, PTLs that are more suitable for transport between distant logic blocks. Next, we present experimental results of PTL lengths ranging from 1.2-12 mm over the same 10-70 GHz frequency range. Finally, we report on the design of circuits for investigating crosstalk between two PTLs and their measurement results.

IEEE Transactions on Applied Superconductivity•Feb 26, 2021•14 citations

The development and characterisation of a parameterised RSFQ cell library for layout synthesis

Lieze Schindler

ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.

•Mar 1, 2021•3 citations
The introduction of passive-transmission-line (PTL) wiring to large-scale SFQ logic circuits offers several advantages over traditional Josephson-transmission-line (JTL) wiring, such as smaller wiring area, less delay, lower power consumption, and more freedom in routing. PTL wiring can drastically change the style of designing SFQ logic circuits. We propose a new methodology for designing large-scale SFQ circuits using PTL wiring. Aiming at generalizing SFQ circuit design, we chose synchronous clocking. We developed a placer that was suitable for SFQ circuit design to assist us with the new design methodology. The placer first synthesizes an H-tree clock distribution network, placing SFQ pulse splitter cells at each branch. It then places logic cells to minimize the maximum length of data PTL wires, aiming at higher operating speeds. Finally, a router completes the PTL wiring. To evaluate the design methodology we designed an 8-bit general purpose RISC processor. Within twelve hours, we obtained a 15-mm-square SFQ circuit that could operate up to 27.6 GHz. We adopted an advanced Nb process, which was characterized by a critical current density of 10 kA/cm2, two 5-mum-wide PTL wiring layers, and a minimum cell size of 30 mum times 30 mum. The circuit consisted of about 20,000 logic cells, which approximated more than 400,000 Josephson junctions including splitters to distribute the clock signal.
We have developed a method of designing single-flux-quantum (SFQ) logic circuits with passive gate-to-gate interconnections. Based on our method, we designed a 2/spl times/2 switch in which all the interconnections are implemented with passive transmission lines (PTLs) while short Josephson transmission line (JTL) segments are used only to adjust the signal timings. Compared with an identical switch using JTL interconnections, the switch using PTL interconnections has 45% fewer wiring junctions and requires 48% less wiring power current. The switch operated at 40 GHz with a bias margin of /spl plusmn/9.5%.
We developed a design approach for interface circuits to connect Single Flux Quantum (SFQ) cells by using passive transmission lines (PTL's). In the approach, an interface circuit between a PTL and JTL is optimized to obtain a standard interface circuit, and then, modifications are made to previously designed SFQ cells and the standard interface circuit to connect the SFQ cells by using PTL's. The key point is the use of approximately the same interface circuit with every SFQ cell to maintain the matching condition between the interface circuit and the PTL's. Based on this approach, we designed an interface circuit and a test circuit composed of two D-flip-flops connected using 2-mm-long PTL's via the interface circuits. The impedance of the PTL was 2 /spl Omega/. We achieved high-speed operation of the test circuit up to 35 GHz with a bias margin of -15/+30%.
The increasing complexity of modern rapid single flux quantum (RSFQ) circuits has made on-chip signal routing, an issue of growing importance. In this paper, several methods for routing large-scale RSFQ circuits are described, and a process is presented for determining when to use passive microstrip transmission lines (PTL) and active Josephson transmission lines (JTL). The effect of the size of the JTL inductor and Josephson junctions on the length of a JTL chain for a target delay is also discussed. The dependence of the JTL inductance on the physical layout is evaluated, and the effects of the primary PTL parameters on delay are characterized. A novel PTL driver and receiver configuration is also proposed. Tradeoffs among the number of JJs, inductance, and length of a PTL stripline in the receiver and driver circuits are reported. The energy dissipation is evaluated for two different interconnects. A tradeoff between the proposed PTL circuits and an optimized JTL in terms of energy dissipation and delay is discussed. Guidelines for choosing the optimal element values are determined, and a simulated bias margin of ±29% for the bias current of the proposed receiver operating at 20 GHz in a 10 kA/cm2technology for a 1-mm transmission line is achieved. Summarizing, guidelines and design tradeoffs appropriate for automated layout and synthesis are provided for driving long interconnect in SFQ VLSI circuits.
An automated layout design flow for rapid single-flux-quantum circuits is proposed in this article. In order to realize small circuit area and low latency, both Josephson transmission lines (JTLs) and passive transmission lines (PTLs) are used for interconnects. Placement and routing are performed considering effective use of JTLs and PTLs. Logic cells are grouped into clusters, and JTLs are used inside clusters. PTLs are used among clusters. The placement process is composed of three steps: first, cell clustering, second, cell placement and JTL routing in each cluster, and third, cluster placement. After the placement process, routing among clusters are performed using PTLs. We applied the proposed design flow to sample circuits with several hundreds of gates. Though the circuit area is not fully optimized, the latency of the circuits designed by the proposed design flow are lower than those of the circuits designed manually.
Passive transmission lines (PTLs) provide an energy-efficient means of transporting pulsed single flux quantum (SFQ) signals between logic gates and blocks on a chip, or even between chips through a multi-chip module carrier. Although functional up to 70 GHz, our previous designs manifested sharp, length-dependent resonances resulting in diminished operating margins. These are particularly inconvenient since the resonant length is about 1 mm at 40–50 GHz, where most SFQ circuits currently function. To avoid the need to keep the PTLs < 1 mm in length, we have optimized the PTL driver-receiver pairs to sufficiently suppress these resonances; this helps facilitate the use of automated routing tools. We present experimental results, in the 10-70 GHz frequency range, for different driver-receiver pairs designed for PTLs in our dual RSFQ-ERSFQ cell library. This cell library, targeting MIT Lincoln Laboratory's SFQ5ee fabrication process, uses PTLs with two types of ground plane configuration. The first variant has signal in M1 and/or M3 with symmetrical ground planes in M0, M2 and/or M2, M4 respectively. The second variant has signal in M2 and/or M3 with asymmetrical ground planes in M1 and M4. We also present a comparison with wider, 4 Ω, PTLs that are more suitable for transport between distant logic blocks. Next, we present experimental results of PTL lengths ranging from 1.2-12 mm over the same 10-70 GHz frequency range. Finally, we report on the design of circuits for investigating crosstalk between two PTLs and their measurement results.
ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.