Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)

Superconducting single photon detectors

Sae Woo Nam, Brice Calkins, T. Gerritts, Sean David Harrington, Adriana E. Lita, Francesco Marsili, Varun Boehm Verma, Igor Vayshenker, Richard P. Mirin, Matthew D. Shaw, William H. Farr, J. A. Stern

Published May 1, 2013• 0 citations
Publisher

Abstract

There is increasing interest in using superconducting optical photon detectors in a variety of applications. These applications require detectors that have extremely low dark count rates, high count rates, and high quantum efficiency. I will describe our work on two types of superconducting detectors, the Superconducting Nanowire Single Photon Detector (SNSPD or nSSPD) and superconducting Transition-Edge Sensor (TES). An SNSPD is an ultra-thin, ultra-narrow (nm scale) superconducting meander that is current biased just below its critical current density. When one or more photon is absorbed, a hot spot is formed that causes the superconductor to develop a resistance and consequently a voltage pulse. At NIST and JPL, we have been developing nanowire detectors using an amorphous alloy of tungsten-silicide. An example of this detector is shown in Fig 1(a). In this case, there are two tungsten silicide layers separated by a dielectric layer to optimize detection of light for any polarization[1]. Fig 1(b) is an example of a TES detector with gold cooling fins to enhance timing of the detector[2]. By exploiting the sharp superconducting-to-normal resistive transition of tungsten at 100mK, TES detectors give an output signal that is proportional to the cumulative energy in an absorption event. This proportional pulse-height enables the determination of the energy absorbed by the TES and the direct conversion of sensor pulse-height into photon number. I will discuss our progress towards developing both types of detectors with quantum efficiencies approaching 100%.

DOI
10.1109/cleoe-iqec.2013.6801983

Related papers

High-efficiency Superconducting Single-photon Detectors

Thomas Gerrits, Adrian Lita, Varun Boehm Verma +4 more

Superconducting single-photon detectors have been shown to have extremely high detection efficiency over a large wavelength range, typically exceeding 90 % [1, 2]. Their use in quantum and classical optics is becoming more and more widespread in part due to improvements to and ease of use of the cryogenic packaging. In this talk, we will review two superconducting detector technologies, the superconducting nanowire single-photon detector (SNSPD) and the optical transition-edge sensor (TES) [3], that are being developed at NIST. We will also describe their applications in quantum and classical optics and present our recent effort to use these detectors as calibration standards, as well as our effort to establish a single-photon detector calibration service. Superconducting Nanowire Single Photon Detectors The SNSPD is based on a meandering, narrow, thin superconducting nanowire, current-biased close to its critical current. Our SNSPDs operate at temperatures around 1K. When a photon is absorbed in the detection region, the energy deposited drives the wire normal and a voltage pulse can be observed. Due to the speed of the detection process, the SNSPD offers high timing resolution along with detection of the photon flux at the shot-noise limit. The combination of both these features yields a detector that can measure the photon’s arrival time from a faint object or source. SNSPDs also offer single-photon detection capability beyond the wavelength detection range of silicon and InGaAs, out to at least 5000 nm [4]. SNSPDs were also recently implemented in an 8×8-pixel array enabling low-resolution, real-time imaging [5]. For our calibration service effort, we built an SNSPD system that can be used as a transfer standard between labs for single-photon detector calibrations. Transition Edge Sensors In contrast to the SNSPD, the TES is a photon-number resolving detector that has almost unity detection efficiency. The TES consists of a superconducting thin film, voltage-biased so that its resistance is in the transition between the superconducting regime and the normal conducting regime. The steep slope of the resistive transition allows for small temperature changes to be measured. The TES is designed such that the absorption of a single photon increases the temperature of the superconducting film enough to discern the resulting signal from the TES system noise. Therefore, the TES needs to be electrically and thermally quiet and is generally operated at temperatures around 100 mK. Due to its energy resolving capability, the TES can be also used as a spectrally resolving single-photon detector with limited resolution [6]. The TES can also be operated as a cryogenic radiometer in combination with an electrical substitution method, and can, in principle, yield absolute calibration of optical powers on the order of a few tens of femtowatts [7]. References 1 A. E. Lita, A. J. Miller, and S. W. Nam, Opt. Express 16, 3032 (2008). 2 F. Marsili, et al., Nat Photon 7, 210 (2013). 3 R. Hadfield and G. Johansson, Superconducting Devices in Quantum Optics (Springer, 2016). 4 F. Marsili, et al., in CLEO: 2013 (OSA, San Jose, California, 2013), p. CTu1H.1. 5 M. S. Allman, et al., Applied Physics Letters 106, 192601 (2015). 6 M. Fortsch, et al., Journal of Optics 17, 065501 (2015). 7 N. A. Tomlin, J. H. Lehman, and S. Nam, Optics Letters 37, 2346 (2012).

•Jan 1, 2018•0 citations

Superconducting nanowire avalanche photodetectors

Sae Woo Nam, Brice Calkins, T. Gerritts +9 more

Superconducting devices offer the potential to perform at speeds and detection efficiencies higher than what is possible using conventional technologies (such as semiconducting avalanche photodiodes and photomultiplier tubs) for wavelengths from the ultraviolet to the mid-infrared. As a result, there has been increasing interest in using superconducting optical photon detectors in a variety of applications. There has been significant progress in using these types of detectors in areas of basic research such as quantum information science and quantum optics. These applications require detectors that have extremely low dark count rates, high count rates, and high quantum efficiency. I will begin by describing some of our earlier work on superconducting Transition-Edge Sensor (TES). In particular, I will describe some of the engineering involved in the cryogenic, electrical, and optical packaging so that these devices can be easily coupled into fiber-based optics. I will also describe our recent work on developing superconducting nanowire single photon detectors (SNSPD or SSPD). An SNSPD is an ultra-thin, ultra-narrow (nm scale) superconducting meander that is current biased just below its critical current density. When one or more photon is absorbed, a hot spot is formed that causes the superconductor to develop a resistance and consequently a voltage pulse. At NIST and JPL, we have been developing nanowire detectors using an amorphous alloy of tungsten-silicide. We will describe to construct systems using tungsten-silicide nanowires to achieve high detection efficiency (>90% at 1550nm). I will also describe our work to improve the performance of the device by fabricating multiple nanowires in an electrically parallel structure to implement a superconducting nanowire avalanche photodiode (SNAP)[1]. One example of this type of detector is shown in Fig 1. In this case, there are two tungsten silicide layers separated by a dielectric layer to optimize detection of light for any polarization[2]. In addition, progress on other types of SNAP detectors will be described to increase the signal size from a single photon, reduce the recovery time of the device, and to improve the jitter.

IEEE Photonics Conference•Sep 1, 2013•4 citations

Single photon detectors using superconductors for quantum information and communications

Sae Woo Nam

Because of the possibility of high efficiency and high rate detection of single photons with low dark counts, there is increasing interest in using superconducting optical photon detectors in a variety of applications in quantum information science and technology. I will describe our work on two types of superconducting detectors, the Superconducting Single Photon Detector (SSPD) and superconducting Transition-Edge Sensor (TES).

Frontiers in Optics•Jan 1, 2008•0 citations

Photon counting statistics of superconducting single-photon detectors made of a three-layer WSi film

Irina Florya, Yu. P. Korneeva, M. Yu. Mikhaĭlov +3 more

Superconducting nanowire single-photon detectors (SNSPD) are used in quantum optics when record-breaking time resolution, high speed, and exceptionally low levels of dark counts (false readings) are required. Their detection efficiency is limited, however, by the absorption coefficient of the ultrathin superconducting film for the detected radiation. One possible way of increasing the detector absorption without limiting its broadband response is to make a detector in the form of several vertically stacked layers and connect them in parallel. For the first time we have studied single-photon detection in a multilayer structure consisting of three superconducting layers of amorphous tungsten silicide (WSi) separated by thin layers of amorphous silicon. Two operating modes of the detector are illustrated: an avalanche regime and an arm-trigger regime. A shift in these modes occurs at currents of ∼0.5–0.6 times the critical current of the detector.

Low Temperature Physics•Mar 1, 2018•9 citations

Single-photon detection in few-layer NbSe2 superconducting nanowires

Lucio Zugliani, Alessandro Palermo, Bianca Scaparra +11 more

Abstract Superconducting Nanowire Single-Photon Detectors (SNSPDs) are key building blocks for photonic quantum technologies due to their ability to detect single photons with ultra-high efficiency, low dark counts and fast temporal resolution. Superconducting materials exhibiting high uniformity, large absorption cross-section and atomic-scale thickness are desirable to extend single-photon detection from the near-infrared up to the terahertz regime, where existing material choices are especially constrained. Substrate independence would further open the way to integrating detectors onto functional materials and heterostructures, enhancing performance and enabling proximal readout of a wide range of individual excitations. Here, we pattern the prototypical two-dimensional superconductor niobium diselenide (NbSe 2 ) into few-layer nanowires less than 100 nm wide and demonstrate single-photon detection at 780 nm and 1550 nm. At the same time, the dark-count rate remains below 1 Hz up to the switching current and we achieve a timing jitter below 50 ps. We estimate via a diffusive hot-spot model that materials and geometric parameters would allow a theoretical cut-off wavelength in the millimetre range, assuming state-of-the-art device parameters. Our results open up routes toward quantum-limited detectors integrated into quantum-photonic circuits and quantum devices, with the potential for novel detection capabilities and unprecedented energy sensitivity.

arXiv:2508.18843•Nature Communications•Jul 29, 2026•1 citation

Superconducting single photon detectors for ultrasensitive visible and IR detection

R. Espiau de Lamaëstre, L. Maingault, Laurent Frey +5 more

Superconducting single photons detectors (SSPDs) have emerged in recent years as a promising alternative for fast and sensitive infrared detectors working in the photon counting mode. In particular, those detectors combine very low dark count rates (below 1 Hz), high speed (above 1GHz), photon number resolution and reasonable quantum efficiency (10 % at telecom wavelengths). They already found applications in quantum cryptography systems and integrated circuit failure analysis, but could also be used as ultimate sensors in matrix configurations. We show here the optimization of SSPD fabrication and their optical metrology at CEA. SSPD are fabricated by patterning a 80 nm wide nanowire in a very thin (4 nm) NbN film on sapphire, forming a pixel of several microns size. A cryogenic all-fibered optoelectronic system has been developed and allows precise metrology of the optical performances of SSPD. When biasing near the critical current of the nanowire, we demonstrate a detection quantum efficiency of 8 % at 1.55 μm, which is also found to be strongly polarization dependent. This quantum efficiency being limited by optical absorption, we propose a prism coupling based absorption enhancing structure that allows reaching 100 % quantum efficiency.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jan 22, 2009•4 citations
There is increasing interest in using superconducting optical photon detectors in a variety of applications. These applications require detectors that have extremely low dark count rates, high count rates, and high quantum efficiency. I will describe our work on two types of superconducting detectors, the Superconducting Nanowire Single Photon Detector (SNSPD or nSSPD) and superconducting Transition-Edge Sensor (TES). An SNSPD is an ultra-thin, ultra-narrow (nm scale) superconducting meander that is current biased just below its critical current density. When one or more photon is absorbed, a hot spot is formed that causes the superconductor to develop a resistance and consequently a voltage pulse. At NIST and JPL, we have been developing nanowire detectors using an amorphous alloy of tungsten-silicide. An example of this detector is shown in Fig 1(a). In this case, there are two tungsten silicide layers separated by a dielectric layer to optimize detection of light for any polarization[1]. Fig 1(b) is an example of a TES detector with gold cooling fins to enhance timing of the detector[2]. By exploiting the sharp superconducting-to-normal resistive transition of tungsten at 100mK, TES detectors give an output signal that is proportional to the cumulative energy in an absorption event. This proportional pulse-height enables the determination of the energy absorbed by the TES and the direct conversion of sensor pulse-height into photon number. I will discuss our progress towards developing both types of detectors with quantum efficiencies approaching 100%.
Superconducting single-photon detectors have been shown to have extremely high detection efficiency over a large wavelength range, typically exceeding 90 % [1, 2]. Their use in quantum and classical optics is becoming more and more widespread in part due to improvements to and ease of use of the cryogenic packaging. In this talk, we will review two superconducting detector technologies, the superconducting nanowire single-photon detector (SNSPD) and the optical transition-edge sensor (TES) [3], that are being developed at NIST. We will also describe their applications in quantum and classical optics and present our recent effort to use these detectors as calibration standards, as well as our effort to establish a single-photon detector calibration service. Superconducting Nanowire Single Photon Detectors The SNSPD is based on a meandering, narrow, thin superconducting nanowire, current-biased close to its critical current. Our SNSPDs operate at temperatures around 1K. When a photon is absorbed in the detection region, the energy deposited drives the wire normal and a voltage pulse can be observed. Due to the speed of the detection process, the SNSPD offers high timing resolution along with detection of the photon flux at the shot-noise limit. The combination of both these features yields a detector that can measure the photon’s arrival time from a faint object or source. SNSPDs also offer single-photon detection capability beyond the wavelength detection range of silicon and InGaAs, out to at least 5000 nm [4]. SNSPDs were also recently implemented in an 8×8-pixel array enabling low-resolution, real-time imaging [5]. For our calibration service effort, we built an SNSPD system that can be used as a transfer standard between labs for single-photon detector calibrations. Transition Edge Sensors In contrast to the SNSPD, the TES is a photon-number resolving detector that has almost unity detection efficiency. The TES consists of a superconducting thin film, voltage-biased so that its resistance is in the transition between the superconducting regime and the normal conducting regime. The steep slope of the resistive transition allows for small temperature changes to be measured. The TES is designed such that the absorption of a single photon increases the temperature of the superconducting film enough to discern the resulting signal from the TES system noise. Therefore, the TES needs to be electrically and thermally quiet and is generally operated at temperatures around 100 mK. Due to its energy resolving capability, the TES can be also used as a spectrally resolving single-photon detector with limited resolution [6]. The TES can also be operated as a cryogenic radiometer in combination with an electrical substitution method, and can, in principle, yield absolute calibration of optical powers on the order of a few tens of femtowatts [7]. References 1 A. E. Lita, A. J. Miller, and S. W. Nam, Opt. Express 16, 3032 (2008). 2 F. Marsili, et al., Nat Photon 7, 210 (2013). 3 R. Hadfield and G. Johansson, Superconducting Devices in Quantum Optics (Springer, 2016). 4 F. Marsili, et al., in CLEO: 2013 (OSA, San Jose, California, 2013), p. CTu1H.1. 5 M. S. Allman, et al., Applied Physics Letters 106, 192601 (2015). 6 M. Fortsch, et al., Journal of Optics 17, 065501 (2015). 7 N. A. Tomlin, J. H. Lehman, and S. Nam, Optics Letters 37, 2346 (2012).
Superconducting devices offer the potential to perform at speeds and detection efficiencies higher than what is possible using conventional technologies (such as semiconducting avalanche photodiodes and photomultiplier tubs) for wavelengths from the ultraviolet to the mid-infrared. As a result, there has been increasing interest in using superconducting optical photon detectors in a variety of applications. There has been significant progress in using these types of detectors in areas of basic research such as quantum information science and quantum optics. These applications require detectors that have extremely low dark count rates, high count rates, and high quantum efficiency. I will begin by describing some of our earlier work on superconducting Transition-Edge Sensor (TES). In particular, I will describe some of the engineering involved in the cryogenic, electrical, and optical packaging so that these devices can be easily coupled into fiber-based optics. I will also describe our recent work on developing superconducting nanowire single photon detectors (SNSPD or SSPD). An SNSPD is an ultra-thin, ultra-narrow (nm scale) superconducting meander that is current biased just below its critical current density. When one or more photon is absorbed, a hot spot is formed that causes the superconductor to develop a resistance and consequently a voltage pulse. At NIST and JPL, we have been developing nanowire detectors using an amorphous alloy of tungsten-silicide. We will describe to construct systems using tungsten-silicide nanowires to achieve high detection efficiency (>90% at 1550nm). I will also describe our work to improve the performance of the device by fabricating multiple nanowires in an electrically parallel structure to implement a superconducting nanowire avalanche photodiode (SNAP)[1]. One example of this type of detector is shown in Fig 1. In this case, there are two tungsten silicide layers separated by a dielectric layer to optimize detection of light for any polarization[2]. In addition, progress on other types of SNAP detectors will be described to increase the signal size from a single photon, reduce the recovery time of the device, and to improve the jitter.
Superconducting nanowire single-photon detectors (SNSPD) are used in quantum optics when record-breaking time resolution, high speed, and exceptionally low levels of dark counts (false readings) are required. Their detection efficiency is limited, however, by the absorption coefficient of the ultrathin superconducting film for the detected radiation. One possible way of increasing the detector absorption without limiting its broadband response is to make a detector in the form of several vertically stacked layers and connect them in parallel. For the first time we have studied single-photon detection in a multilayer structure consisting of three superconducting layers of amorphous tungsten silicide (WSi) separated by thin layers of amorphous silicon. Two operating modes of the detector are illustrated: an avalanche regime and an arm-trigger regime. A shift in these modes occurs at currents of ∼0.5–0.6 times the critical current of the detector.
Abstract Superconducting Nanowire Single-Photon Detectors (SNSPDs) are key building blocks for photonic quantum technologies due to their ability to detect single photons with ultra-high efficiency, low dark counts and fast temporal resolution. Superconducting materials exhibiting high uniformity, large absorption cross-section and atomic-scale thickness are desirable to extend single-photon detection from the near-infrared up to the terahertz regime, where existing material choices are especially constrained. Substrate independence would further open the way to integrating detectors onto functional materials and heterostructures, enhancing performance and enabling proximal readout of a wide range of individual excitations. Here, we pattern the prototypical two-dimensional superconductor niobium diselenide (NbSe 2 ) into few-layer nanowires less than 100 nm wide and demonstrate single-photon detection at 780 nm and 1550 nm. At the same time, the dark-count rate remains below 1 Hz up to the switching current and we achieve a timing jitter below 50 ps. We estimate via a diffusive hot-spot model that materials and geometric parameters would allow a theoretical cut-off wavelength in the millimetre range, assuming state-of-the-art device parameters. Our results open up routes toward quantum-limited detectors integrated into quantum-photonic circuits and quantum devices, with the potential for novel detection capabilities and unprecedented energy sensitivity.
Superconducting single photons detectors (SSPDs) have emerged in recent years as a promising alternative for fast and sensitive infrared detectors working in the photon counting mode. In particular, those detectors combine very low dark count rates (below 1 Hz), high speed (above 1GHz), photon number resolution and reasonable quantum efficiency (10 % at telecom wavelengths). They already found applications in quantum cryptography systems and integrated circuit failure analysis, but could also be used as ultimate sensors in matrix configurations. We show here the optimization of SSPD fabrication and their optical metrology at CEA. SSPD are fabricated by patterning a 80 nm wide nanowire in a very thin (4 nm) NbN film on sapphire, forming a pixel of several microns size. A cryogenic all-fibered optoelectronic system has been developed and allows precise metrology of the optical performances of SSPD. When biasing near the critical current of the nanowire, we demonstrate a detection quantum efficiency of 8 % at 1.55 μm, which is also found to be strongly polarization dependent. This quantum efficiency being limited by optical absorption, we propose a prism coupling based absorption enhancing structure that allows reaching 100 % quantum efficiency.