Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

High-Speed Experimental Demonstration of Adiabatic Quantum-Flux-Parametron Gates Using Quantum-Flux-Latches

Naoki Takeuchi, Thomas Ortlepp, Yuki Yamanashi, Nobuyuki Yoshikawa

Published Apr 7, 2014• 10 citations
Publisher

Abstract

We experimentally demonstrated high-speed logic operations of adiabatic quantum-flux-parametron (AQFP) gates through the use of quantum-flux-latches (QFLs). In QFL-based high-speed test circuits (QHTCs), the output data of the circuits under test (CUTs), which are driven by high-speed excitation currents, are stored in QFLs and are slowly read out using low-speed excitation currents. We designed and fabricated three types of QHTCs using QFLs with different circuit parameters, where the CUTs were buffer gates and and gates. We confirmed the correct operation of buffer gates and and gates at 1 GHz. The obtained bias margins of the 1 GHz excitation currents were more than ±30% for each QHTC, which is wide enough for high-speed logic operations of AQFP gates.

DOI
10.1109/tasc.2014.2311444

Related papers

Experimental demonstration of quantum-flux-latch-based circuits

Naoki Takeuchi, Thomas Ortlepp, Yuki Yamanashi +1 more

We propose and discuss quantum-flux-latch (QFL) based circuits for adiabatic quantum-flux-parametron (AQFP) logic. The QFL-based XOR (QXOR) gate is a novel XOR gate. The circuit schematic of the QXOR is the same as that of a QFL, but QXORs operate on a different operation principle due to ac biasing. We designed and fabricated the QXOR and the half adder including a QXOR. We successfully demonstrated correct logic operations of these circuits at 4.2 K in the low-speed function test. Also, we estimated the energy dissipation of the QFL using a circuit simulator. The estimated energy dissipation was $\sim$0.2 aJ/cycle.

IEEE Transactions on Applied Superconductivity•Jan 1, 2014•2 citations

Majority Gate-Based Feedback Latches for Adiabatic Quantum Flux Parametron Logic

Naoki TSUJI, Naoki Takeuchi, Yuki Yamanashi +2 more

We have studied ultra-low-power superconductor circuits using adiabatic quantum flux parametron (AQFP) logic. Latches, which store logic data in logic circuits, are indispensable logic elements in the realization of AQFP computing systems. Among them, feedback latches, which hold data by using a feedback loop, have advantages in terms of their wide operation margins and high stability. Their drawbacks are their large junction counts and long latency. In this paper, we propose a majority gate-based feedback latch for AQFP logic with a reduced number of junctions. We designed and fabricated the proposed AQFP latches using a standard National Institute of Advanced Industrial Science and Technology (AIST) process. The measurement results showed that the feedback latches operate with wide operation margins that are comparable with circuit simulation results.

IEICE Transactions on Electronics•Jan 1, 2016•12 citations

Magnetically coupled quantum-flux-latch with wide operation margins

Naoki Tsuji, Naoki Takeuchi, Tatsuya Narama +3 more

Abstract We have been developing adiabatic quantum-flux-parametron (AQFP) circuits as an ultra-low-power superconductor logic for energy-efficient computing. In a previous study, we proposed and demonstrated a quantum-flux-latch (QFL), which is a compact and compatible latch for AQFP logic. The QFL is composed of an AQFP buffer gate and a storage loop, which are directly connected to each other. However, the operation margins were not sufficiently wide due to a trade-off between the operation margins of the storage loop and that of the buffer gate. In this present study, we propose a magnetically coupled QFL (MC-QFL), where the storage loop and the buffer gate are physically separated and magnetically coupled to each other to eliminate the trade-off in the operation margins. The simulation results showed that the critical parameter margin of the MC-QFL is twice as large as that of the previously designed QFL. For comparison, we fabricated and demonstrated both the previously designed QFL and the newly designed MC-QFL. The measurement results showed that the MC-QFL has wider operation margins compared with the previously designed QFL.

Superconductor Science and Technology•Sep 29, 2015•4 citations

A High-Speed Interface Based on a Josephson Latching Driver for Adiabatic Quantum-Flux-Parametron Logic

Fumihiro China, Naoki Takeuchi, Hideo Suzuki +3 more

The adiabatic quantum flux parametron (AQFP) is an energy-efficient, high-speed superconducting logic device. To observe the tiny output currents from the AQFP in experiments, high-speed voltage drivers are indispensable. In the present study, we develop a compact voltage driver for AQFP logic based on a Josephson latching driver (JLD), which has been used as a high-speed driver for rapid single-flux-quantum (RSFQ) logic. In the JLD-based voltage driver, the signal currents of AQFP gates are converted into gap-voltage-level signals via an AQFP/RSFQ interface and a four-junction logic gate. Furthermore, this voltage driver includes only 15 Josephson junctions, which is much fewer than in the case for the previously designed driver based on dc superconducting quantum interference devices (60 junctions). In measurement, we successfully operate the JLD-based voltage driver up to 4 GHz. We also evaluate the bit error rate (BER) of the driver and find that the BER is 7.92×10-10 and 2.67×10-3 at 1GHz and 4GHz, respectively.

IEICE Transactions on Electronics•Dec 2, 2021•3 citations

Adiabatic quantum-flux-parametron boosters for long interconnection and large fanouts

Naoya Mizushima, Naoki Takeuchi, Yuki Yamanashi +1 more

Abstract Adiabatic quantum flux parametron (AQFP) is energy-efficient superconducting logic that operates with zero static energy consumption and extremely small dynamic energy consumption thanks to the adiabatic switching of the logic gates. One drawback in AQFP logic circuits is the wire length and fan-out limitations because of the low driving ability of the logic gates, which results in a large circuit area and significant latency. In the present study, we propose AQFP boosters with high driving ability. Two types of AQFP boosters are proposed: one is composed of a parallel connection of AQFP buffers, and the other uses multistage buffers driven by one excitation clock. We evaluated the maximum wire length of the proposed boosters by circuit simulations, including thermal noises, and found that the maximum wire length is 3.9 mm for fan-out one and 1 mm for fan-out four. We implemented the boosters and demonstrated their correct operations at low-speed tests. We also demonstrated a 5-to-31 decoder using the proposed boosters. It was shown that the circuit area, latency, and energy consumption were improved by about 30% compared to the design without the boosters.

Superconductor Science and Technology•Aug 11, 2023•4 citations

Design and Demonstration of Interface Circuits Between Rapid Single-Flux-Quantum and Adiabatic Quantum-Flux-Parametron Circuits

Fumihiro China, Tatsuya Narama, Naoki Takeuchi +3 more

We investigated interface circuits between rapid single-flux-quantum (RSFQ) circuits and adiabatic quantum-flux-parametron (AQFP) circuits for a high-speed and low-power hybrid computing system. In addition, the interface circuits allow us to use long-distance interconnections based on single-flux-quantum (SFQ) passive transmission lines between AQFP gates. The target frequency of interface circuits is several gigahertz. There are two types of interface circuits. The RSFQ/AQFP interface circuit, which transmits a signal from RSFQ circuits to AQFP gates, was realized by coupling an RSFQ toggle flip-flop (TFF) to an AQFP buffer gate. The simulated bias margins of the RSFQ TFF and the excitation current margin of the RSFQ/AQFP interface were 2.22 mA ± 24.7% and 1.71 mA ± 25.0%, respectively. The AQFP/RSFQ interface circuit, which transmits a signal from AQFP gates to RSFQ circuits, was designed by using a high-sensitive magnetically coupled dc/SFQ converter (MC-dc/SFQ) to detect an output current of an AQFP buffer gate. The simulated bias margins of the MC-dc/SFQ and the excitation current margin of the AQFP/RSFQ interface were 0.558 mA ± 20.5% and 1.95 mA ± 36.1%, respectively. We also fabricated and measured the interface circuits.

IEEE Transactions on Applied Superconductivity•Jun 7, 2016•19 citations
We experimentally demonstrated high-speed logic operations of adiabatic quantum-flux-parametron (AQFP) gates through the use of quantum-flux-latches (QFLs). In QFL-based high-speed test circuits (QHTCs), the output data of the circuits under test (CUTs), which are driven by high-speed excitation currents, are stored in QFLs and are slowly read out using low-speed excitation currents. We designed and fabricated three types of QHTCs using QFLs with different circuit parameters, where the CUTs were buffer gates and and gates. We confirmed the correct operation of buffer gates and and gates at 1 GHz. The obtained bias margins of the 1 GHz excitation currents were more than ±30% for each QHTC, which is wide enough for high-speed logic operations of AQFP gates.
We propose and discuss quantum-flux-latch (QFL) based circuits for adiabatic quantum-flux-parametron (AQFP) logic. The QFL-based XOR (QXOR) gate is a novel XOR gate. The circuit schematic of the QXOR is the same as that of a QFL, but QXORs operate on a different operation principle due to ac biasing. We designed and fabricated the QXOR and the half adder including a QXOR. We successfully demonstrated correct logic operations of these circuits at 4.2 K in the low-speed function test. Also, we estimated the energy dissipation of the QFL using a circuit simulator. The estimated energy dissipation was $\sim$0.2 aJ/cycle.
We have studied ultra-low-power superconductor circuits using adiabatic quantum flux parametron (AQFP) logic. Latches, which store logic data in logic circuits, are indispensable logic elements in the realization of AQFP computing systems. Among them, feedback latches, which hold data by using a feedback loop, have advantages in terms of their wide operation margins and high stability. Their drawbacks are their large junction counts and long latency. In this paper, we propose a majority gate-based feedback latch for AQFP logic with a reduced number of junctions. We designed and fabricated the proposed AQFP latches using a standard National Institute of Advanced Industrial Science and Technology (AIST) process. The measurement results showed that the feedback latches operate with wide operation margins that are comparable with circuit simulation results.
Abstract We have been developing adiabatic quantum-flux-parametron (AQFP) circuits as an ultra-low-power superconductor logic for energy-efficient computing. In a previous study, we proposed and demonstrated a quantum-flux-latch (QFL), which is a compact and compatible latch for AQFP logic. The QFL is composed of an AQFP buffer gate and a storage loop, which are directly connected to each other. However, the operation margins were not sufficiently wide due to a trade-off between the operation margins of the storage loop and that of the buffer gate. In this present study, we propose a magnetically coupled QFL (MC-QFL), where the storage loop and the buffer gate are physically separated and magnetically coupled to each other to eliminate the trade-off in the operation margins. The simulation results showed that the critical parameter margin of the MC-QFL is twice as large as that of the previously designed QFL. For comparison, we fabricated and demonstrated both the previously designed QFL and the newly designed MC-QFL. The measurement results showed that the MC-QFL has wider operation margins compared with the previously designed QFL.
The adiabatic quantum flux parametron (AQFP) is an energy-efficient, high-speed superconducting logic device. To observe the tiny output currents from the AQFP in experiments, high-speed voltage drivers are indispensable. In the present study, we develop a compact voltage driver for AQFP logic based on a Josephson latching driver (JLD), which has been used as a high-speed driver for rapid single-flux-quantum (RSFQ) logic. In the JLD-based voltage driver, the signal currents of AQFP gates are converted into gap-voltage-level signals via an AQFP/RSFQ interface and a four-junction logic gate. Furthermore, this voltage driver includes only 15 Josephson junctions, which is much fewer than in the case for the previously designed driver based on dc superconducting quantum interference devices (60 junctions). In measurement, we successfully operate the JLD-based voltage driver up to 4 GHz. We also evaluate the bit error rate (BER) of the driver and find that the BER is 7.92×10-10 and 2.67×10-3 at 1GHz and 4GHz, respectively.
Abstract Adiabatic quantum flux parametron (AQFP) is energy-efficient superconducting logic that operates with zero static energy consumption and extremely small dynamic energy consumption thanks to the adiabatic switching of the logic gates. One drawback in AQFP logic circuits is the wire length and fan-out limitations because of the low driving ability of the logic gates, which results in a large circuit area and significant latency. In the present study, we propose AQFP boosters with high driving ability. Two types of AQFP boosters are proposed: one is composed of a parallel connection of AQFP buffers, and the other uses multistage buffers driven by one excitation clock. We evaluated the maximum wire length of the proposed boosters by circuit simulations, including thermal noises, and found that the maximum wire length is 3.9 mm for fan-out one and 1 mm for fan-out four. We implemented the boosters and demonstrated their correct operations at low-speed tests. We also demonstrated a 5-to-31 decoder using the proposed boosters. It was shown that the circuit area, latency, and energy consumption were improved by about 30% compared to the design without the boosters.
We investigated interface circuits between rapid single-flux-quantum (RSFQ) circuits and adiabatic quantum-flux-parametron (AQFP) circuits for a high-speed and low-power hybrid computing system. In addition, the interface circuits allow us to use long-distance interconnections based on single-flux-quantum (SFQ) passive transmission lines between AQFP gates. The target frequency of interface circuits is several gigahertz. There are two types of interface circuits. The RSFQ/AQFP interface circuit, which transmits a signal from RSFQ circuits to AQFP gates, was realized by coupling an RSFQ toggle flip-flop (TFF) to an AQFP buffer gate. The simulated bias margins of the RSFQ TFF and the excitation current margin of the RSFQ/AQFP interface were 2.22 mA ± 24.7% and 1.71 mA ± 25.0%, respectively. The AQFP/RSFQ interface circuit, which transmits a signal from AQFP gates to RSFQ circuits, was designed by using a high-sensitive magnetically coupled dc/SFQ converter (MC-dc/SFQ) to detect an output current of an AQFP buffer gate. The simulated bias margins of the MC-dc/SFQ and the excitation current margin of the AQFP/RSFQ interface were 0.558 mA ± 20.5% and 1.95 mA ± 36.1%, respectively. We also fabricated and measured the interface circuits.