Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

A cell-based design approach for RSFQ circuits based on binary decision diagram

Junichi Koshiyama, Nobuyuki Yoshikawa

Published Mar 1, 2001• 6 citations
Publisher

Abstract

We have proposed a cell-based design approach for rapid single flux quantum (RSFQ) logic circuits. In our design approach, a binary decision diagram (BDD) is used for representation of logical functions in order to reduce the number of gates. We have made a standard cell library, which is composed of only five basic cells. We add one-junction Josephson transmission line (JTL) to the edge of the input and the output node of some basic cells, by which no deterioration of the DC bias margin is observed for the connection of each cell. In the layout level, the size and the position of the input/output node of each cell are equalized. The standard cell circuits were fabricated by NEC 2.5 kA/cm/sup 2/ and Hypres 1.0 kA/cm/sup 2/ Nb standard process and they were tested at low speed.

DOI
10.1109/77.919334

Related papers

Design and implementation of a RSFQ superconductive digital electronics cell library

Rodwell S. Bakolo

ENGLISH ABSTRACT: Rapid Single Flux Quantum (RSFQ) cells are key in the design of complex and applicable RSFQ electronic circuits. These cells are low-level circuit elements that are used repeatedly to build larger, applicable RSFQ circuitry. Making these cells simple to layout and manufacture, but reliable for extensive use demands a careful development process for RSFQ cells. Cell functionality is verified through simulations, thereafter the cell is laid out in special software packages. Inductance of on-chip superconductor structures is extracted through careful modelling with numerical field solver software. A cell library has been developed by incorporating existing or published cells after further analysis and optimization, as well as developing new cells. Cells that have been adapted into the library include the Josephson transmission line (JTL), Splitter, Merger, D-Flip Flop (DFF), T-Flip Flop (TFF), NOT, AND, OR and XOR, DC-SFQ and SFQ-DC and PTL Driver and Receivers. New cells include NOR, NAND and XNOR. The cells were designed for the IPHT’s RSFQ1D 1kA/cmª and Hypres’ 4.5kA/cmª processes. The cells in the library have good bias current operating margins obtained through simulations (> ±26%). All cells have all the parameters listed in the thesis including extracted inductance values. In order to have a complete and verified RSFQ cell library, cells have been sent for fabrication at IPHT and Hypres facilities. These cells can now be tested on-chip, in the laboratory, to establish functionality and practical bias current margins. All test signal patterns and bias currents required for testing are defined to allow co-workers or collaborators to test the cells.

•Dec 1, 2011•1 citation

The development and characterisation of a parameterised RSFQ cell library for layout synthesis

Lieze Schindler

ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.

•Mar 1, 2021•3 citations

A new design approach for RSFQ logic circuits based on the binary decision diagram

Nobuyuki Yoshikawa, 博史 多胡, K. Yoneyama

We will propose a new design approach for single-flux-quantum (SFQ) logic circuits based on a binary decision diagram (BDD). The BDD is a way to represent a logical function by using a directed graph, which is composed of nodes having one input (root) and two outputs (branches). The node has binary states internally which can be controlled from outside, and it switches a messenger entering from the root into one of two branches depending on the internal state. It has been proven that any combinational logic can be represented by this basic element. We will show that the BDD is effectively implemented by an SFQ circuit, where the node is replaced with an SFQ D/sub 2/ flip-flop. Important features of the BDD SFQ logic circuit are simplicity of circuit structure, self-timed nature and high modularity. We have designed a BDD SFQ adder and showed that the junction count and latency are smaller than that of the conventional RSFQ adder.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•18 citations

Rapid single-flux-quantum and adiabatic quantum-flux-parametron cell libraries using a 1 kA/cm2 niobium fabrication process

Taiki Yamae, Yuki Hironaka, Shuichi Nagasawa +3 more

Abstract Superconductor logic families can operate with small power dissipation and are thus suitable as building blocks for various computing systems. In some applications, superconductor logic circuits should be designed using Josephson junctions with low I c values ( I c : critical current). For instance, lowering I c values enables qubit interface circuits to operate with very small power dissipation at ~10 mK and stochastic electronics to easily induce stochastic operations. In this study, we develop the AIST 1 kA cm −2 Nb planarized process (1KP) with a minimum critical current of 10 µA, dedicated to the design of qubit interface circuits and stochastic electronics. We also develop rapid single-flux-quantum (RSFQ) and adiabatic quantum-flux-parametron (AQFP) cell libraries using the 1KP. The power dissipation of RSFQ logic using the 1KP can be reduced to 3.2% of that for conventional RSFQ logic by reducing both I c values and a bias voltage. Furthermore, the amount of supply currents for AQFP circuits using the 1KP can be reduced to ~40% of that for conventional AQFP circuits due to a large mutual inductance between AQFP gates and excitation lines, which results from a reduction in I c and an increase in inductances. We demonstrate RSFQ and AQFP circuits fabricated by the 1KP at 4.2 K. These results indicate that RSFQ and AQFP circuits using the 1KP have the potential to be used for the design of qubit interface circuits and stochastic electronics.

Scientific Reports•Nov 21, 2025•4 citations

Design and Verification of SFQ Cell Library for Superconducting LSI Digital Circuits

Xiaoping Gao, Qi Qiao, Mingliang Wang +5 more

We have developed a cell library for superconducting large scale integrated (LSI) digital circuits based on Single Flux Quantum (SFQ) devices. The circuits were designed for a 6-kA/cm2Nb/AlOx/Nb junction process with 10 mask levels including one ground plane and two Nb wiring layers. The initial design and optimization of the circuit parameters were achieved by means of the optimization functions in a circuit simulator, PSCAN2, to ensure that important circuit parameters, Josephson critical current (IC), bias current (Ibias), and inductance satisfied minimal margin requirements. Critical margins of ICand Ibiaswere then further improved manually. To compensate the scattering in the circuit parameters from fabrication by design as much as possible, the critical junction parameters were optimized to further centralize the IC. The library cells were laid out following our design rules determined by systematic experiments on process control monitors (PCM). Basic cells including Josephson transmission lines, splitters, confluence buffers, D flip-flops, T flip-flops, and XOR and NDRO gates were designed, fabricated, and successfully tested at low frequencies. Wide overlaps of the operating regions for the common bias voltages were confirmed.

IEEE Transactions on Applied Superconductivity•Mar 11, 2021•34 citations

Experimental evaluation of some rapid single flux quantum cells

Ying Ki Kwong, V. Nandakumar

Some basic cells in the rapid single-flux quantum (RSFQ) family of superconductive logic circuits were studied. An input stage, a buffer, and an OR gate were simulated and laid out for a standard niobium-based fabrication process. The resulting circuits perform properly for clock speeds up to 1 GHz. For the simpler circuits tested, the measured margins are wide, consistent with simulations, and not very dependent on clock speed. However, margin decreases with increased circuit complexity. The input stage converts a rising edge into an SFQ pulse, which has a small amplitude and narrow width in time. On the present circuits, these pulses are about 200 mu V in amplitude and 10 ps in width. To facilitate measurement, the authors have chosen as the output an asymmetrical superconducting quantum interference device (SQUID) consisting of two Josephson junctions. It converts SFQ pulses into 2.5 mV latching output levels on chip. By inductively coupling SFQ pulses into the SQUID loop, DC current isolation between the RSFQ circuit-under-test and the output stage is provided. The SQUID was optimized for 2 GHz operations.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•7 citations
We have proposed a cell-based design approach for rapid single flux quantum (RSFQ) logic circuits. In our design approach, a binary decision diagram (BDD) is used for representation of logical functions in order to reduce the number of gates. We have made a standard cell library, which is composed of only five basic cells. We add one-junction Josephson transmission line (JTL) to the edge of the input and the output node of some basic cells, by which no deterioration of the DC bias margin is observed for the connection of each cell. In the layout level, the size and the position of the input/output node of each cell are equalized. The standard cell circuits were fabricated by NEC 2.5 kA/cm/sup 2/ and Hypres 1.0 kA/cm/sup 2/ Nb standard process and they were tested at low speed.
ENGLISH ABSTRACT: Rapid Single Flux Quantum (RSFQ) cells are key in the design of complex and applicable RSFQ electronic circuits. These cells are low-level circuit elements that are used repeatedly to build larger, applicable RSFQ circuitry. Making these cells simple to layout and manufacture, but reliable for extensive use demands a careful development process for RSFQ cells. Cell functionality is verified through simulations, thereafter the cell is laid out in special software packages. Inductance of on-chip superconductor structures is extracted through careful modelling with numerical field solver software. A cell library has been developed by incorporating existing or published cells after further analysis and optimization, as well as developing new cells. Cells that have been adapted into the library include the Josephson transmission line (JTL), Splitter, Merger, D-Flip Flop (DFF), T-Flip Flop (TFF), NOT, AND, OR and XOR, DC-SFQ and SFQ-DC and PTL Driver and Receivers. New cells include NOR, NAND and XNOR. The cells were designed for the IPHT’s RSFQ1D 1kA/cmª and Hypres’ 4.5kA/cmª processes. The cells in the library have good bias current operating margins obtained through simulations (> ±26%). All cells have all the parameters listed in the thesis including extracted inductance values. In order to have a complete and verified RSFQ cell library, cells have been sent for fabrication at IPHT and Hypres facilities. These cells can now be tested on-chip, in the laboratory, to establish functionality and practical bias current margins. All test signal patterns and bias currents required for testing are defined to allow co-workers or collaborators to test the cells.
ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.
We will propose a new design approach for single-flux-quantum (SFQ) logic circuits based on a binary decision diagram (BDD). The BDD is a way to represent a logical function by using a directed graph, which is composed of nodes having one input (root) and two outputs (branches). The node has binary states internally which can be controlled from outside, and it switches a messenger entering from the root into one of two branches depending on the internal state. It has been proven that any combinational logic can be represented by this basic element. We will show that the BDD is effectively implemented by an SFQ circuit, where the node is replaced with an SFQ D/sub 2/ flip-flop. Important features of the BDD SFQ logic circuit are simplicity of circuit structure, self-timed nature and high modularity. We have designed a BDD SFQ adder and showed that the junction count and latency are smaller than that of the conventional RSFQ adder.
Abstract Superconductor logic families can operate with small power dissipation and are thus suitable as building blocks for various computing systems. In some applications, superconductor logic circuits should be designed using Josephson junctions with low I c values ( I c : critical current). For instance, lowering I c values enables qubit interface circuits to operate with very small power dissipation at ~10 mK and stochastic electronics to easily induce stochastic operations. In this study, we develop the AIST 1 kA cm −2 Nb planarized process (1KP) with a minimum critical current of 10 µA, dedicated to the design of qubit interface circuits and stochastic electronics. We also develop rapid single-flux-quantum (RSFQ) and adiabatic quantum-flux-parametron (AQFP) cell libraries using the 1KP. The power dissipation of RSFQ logic using the 1KP can be reduced to 3.2% of that for conventional RSFQ logic by reducing both I c values and a bias voltage. Furthermore, the amount of supply currents for AQFP circuits using the 1KP can be reduced to ~40% of that for conventional AQFP circuits due to a large mutual inductance between AQFP gates and excitation lines, which results from a reduction in I c and an increase in inductances. We demonstrate RSFQ and AQFP circuits fabricated by the 1KP at 4.2 K. These results indicate that RSFQ and AQFP circuits using the 1KP have the potential to be used for the design of qubit interface circuits and stochastic electronics.
We have developed a cell library for superconducting large scale integrated (LSI) digital circuits based on Single Flux Quantum (SFQ) devices. The circuits were designed for a 6-kA/cm2Nb/AlOx/Nb junction process with 10 mask levels including one ground plane and two Nb wiring layers. The initial design and optimization of the circuit parameters were achieved by means of the optimization functions in a circuit simulator, PSCAN2, to ensure that important circuit parameters, Josephson critical current (IC), bias current (Ibias), and inductance satisfied minimal margin requirements. Critical margins of ICand Ibiaswere then further improved manually. To compensate the scattering in the circuit parameters from fabrication by design as much as possible, the critical junction parameters were optimized to further centralize the IC. The library cells were laid out following our design rules determined by systematic experiments on process control monitors (PCM). Basic cells including Josephson transmission lines, splitters, confluence buffers, D flip-flops, T flip-flops, and XOR and NDRO gates were designed, fabricated, and successfully tested at low frequencies. Wide overlaps of the operating regions for the common bias voltages were confirmed.
Some basic cells in the rapid single-flux quantum (RSFQ) family of superconductive logic circuits were studied. An input stage, a buffer, and an OR gate were simulated and laid out for a standard niobium-based fabrication process. The resulting circuits perform properly for clock speeds up to 1 GHz. For the simpler circuits tested, the measured margins are wide, consistent with simulations, and not very dependent on clock speed. However, margin decreases with increased circuit complexity. The input stage converts a rising edge into an SFQ pulse, which has a small amplitude and narrow width in time. On the present circuits, these pulses are about 200 mu V in amplitude and 10 ps in width. To facilitate measurement, the authors have chosen as the output an asymmetrical superconducting quantum interference device (SQUID) consisting of two Josephson junctions. It converts SFQ pulses into 2.5 mV latching output levels on chip. By inductively coupling SFQ pulses into the SQUID loop, DC current isolation between the RSFQ circuit-under-test and the output stage is provided. The SQUID was optimized for 2 GHz operations.>