Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Heterodyne Mixing and Direct Detection Performance of a Superconducting NbN Hot-Electron Bolometer

W. Zhang, W. Miao, Kangmin Zhou, S. L. Li, Z. H. Lin, Qi Yao, S. C. Shi

Published Jan 13, 2011• 14 citations
Publisher

Abstract

The heterodyne mixing and direct detection performance of a superconducting NbN hot-electron bolometer (HEB) integrated with a log-spiral antenna have been thoroughly characterized. The corrected receiver noise temperature and IF gain bandwidth are approximately 800 K at 0.5 THz, 750 K at 0.85 THz and 3 GHz at its optimum bias point. In addition, both the receiver noise temperature and IF gain bandwidth were found insensitive to the bath temperature, while the bias point was fixed, in good agreement with those simulated with the hot-spot model taking account of the HEB's current-dependent resistive transition. Furthermore, the HEB's frequency response was measured by a Fourier transform spectrometer at different bias points and bath temperatures. The estimated noise equivalent power (NEP) was close to 10-13W/Hz0.5around the HEB's transition temperature.

DOI
10.1109/tasc.2010.2097576

Related papers

Performance Investigation of a Quasi-Optical NbN HEB Mixer at Submillimeter Wavelength

Wei Miao, Y. Delorme, A. Féret +8 more

In this paper, the performance of a quasi-optical phonon-cooled NbN superconducting hot electron bolometer (HEB) mixer is thoroughly investigated. The variation of the receiver noise temperature and the conversion gain around 600 GHz with respect to DC bias voltage and LO pumping level has been measured. The lowest receiver noise temperature is 750 K and reduced to about 250 K after correcting the quasi-optical losses before the HEB mixer. We compared the measured results with the predictions according to one dimensional distributed hot spot model. A reasonable match between theoretical model and experiment is observed. In addition, the direct response of the HEB mixer (integrated with a log-periodic spiral antenna) is measured by using Fourier Transform Spectrometer (FTS). The stability of the receiver is also investigated by means of Allan variance time measurements performed with an intermediate frequency (IF) bandwidth of 40 MHz.

•Apr 1, 2009•0 citations

Terahertz Direct Detection Characteristics of a Superconducting NbN Bolometer

Yuan Ren, Wei Miao, Qijun Yao +2 more

We report the terahertz direct detection characteristics of a spiral antenna coupled NbN superconducting hot-electron bolometer (HEB) at a bath temperature of 4.2 K. Thermal conductance determined from resistance transition curves with different bias currents is found to be 3 × 10 −7 W/K. The device shows a read-out circuit limited noise equivalent power (NEP) of 4.5 × 10 −12 W/Hz 1/2 at 4.2 K with a home-made transimpedance amplifier operating at room temperature.

Chinese Physics Letters•Jan 1, 2011•14 citations

Doubling of sensitivity and bandwidth in phonon-cooled hot-electron bolometer mixers

J. J. A. Baselmans, Merlijn Hajenius, J. R. Gao +4 more

NbN hot electron bolometer (HEB) mixers are at this moment the best heterodyne detectors for frequencies above 1 THz. However, the fabrication procedure of these devices is such that the quality of the interface between the NbN superconducting film and the contact structure is not under good control. This results in a contact resistance between the NbN bolometer and the contact pad. We compare identical bolometers, with different NbN - contact pad interfaces, coupled with a spiral antenna. We find that cleaning the NbN interface and adding a thin additional superconductor prior to the gold contact deposition improves the noise temperature and the bandwidth of the HEB mixers with more than a factor of 2. We obtain a DSB noise temperature of 950 K at 2.5 THz and a Gain bandwidth of 5-6 GHz. For use in real receiver systems we design small volume (0.15x1 micron) HEB mixers with a twin slot antenna. We find that these mixers combine good sensitivity (900 K at 1.6 THz) with low LO power requirement, which is 160 - 240 nW at the Si lens of the mixer. This value is larger than expected from the isothermal technique and the known losses in the lens by a factor of 3-3.5.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Oct 8, 2004•1 citation

Phonon cooled hot-electron bolometric mixer for 1-5 THz

Heiko Richter, Alexei D. Semenov, Heinz‐Wilhelm Hübers +3 more

Heterodyne receivers for applications in astronomy and planetary research need quantum limited sensitivity. In instruments which are currently built for SOFIA and Herschel, superconducting hot electron bolometers (HEB) are used to achieve this goal at frequencies above 1.4 THz. In order to optimize the performance for this frequency of hot electron bolometer mixers with different in-plane dimensions and logarithmic-spiral feed antennas have been investigated. Their noise temperatures and beam patterns were measured. Above 3 THz the best performance was achieved with a superconducting bridge of 2.0/spl times/0.2 /spl mu/m/sup 2/ incorporated in a logarithmic spiral antenna. The DSB noise temperatures were 2700 K, 4700 and 6400 K at 3.1 THz, 4.3 THz and 5.2 THz, respectively. The results demonstrate that the NbN HEB is very well suited as a mixer for THz heterodyne receivers up to at least 5 THz.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Oct 4, 2006•4 citations

NbN Hot Electron Bolometer Mixers: Sensitivity, LO Power, Direct Detection and Stability

J. J. A. Baselmans, Merlijn Hajenius, J. R. Gao +6 more

We demonstrate that the performance of NbN lattice cooled hot electron bolometer mixers depends strongly on the interface quality between the bolometer and the contact structure. Both the receiver noise temperature and the gain bandwidth can be improved by a factor of 2 by cleaning the interface and adding an additional superconducting interlayer to the contact pad. Using this we obtain a double sideband receiver noise temperature of 950 K at 2.5 THz and 4.3 K, using a 0.4/spl times/4 /spl mu/m HEB mixer with a spiral antenna. At the same bias point, we obtain an IF gain bandwidth of 6 GHz. To comply with current demands on THz mixers for use in space based receivers we reduce the device size to 0.15/spl times/1 /spl mu/m and use a twin slot antenna. We report measurements of the noise temperature, LO power requirement, stability and the direct detection effect, using a mixer with a 1.6 THz twin slot antenna and a 1.462 THz solid state LO source with calibrated output power.

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•30 citations

Terahertz (THz) direct detectors based on superconducting HEBs with thermal, THz and microwave biasing methods (Conference Presentation)

Jian Chen

Superconducting hot electron bolometers (HEBs) are widely used as terahertz (THz) heterodyne detectors (mixers) and becoming the most advantageous candidate for low noise receiver at frequencies above 1.2 THz. However, there is still lack of accurate theoretical modeling which explains the complex mechanism of different aspects of superconducting HEBs. These difficulties do not prevent researchers around the world from making experimental progress. In the last few years, superconducting HEBs are also used as THz direct detectors to develop the array for the applications in biology, medicine and security systems. Recently, a noise equivalent power (NEP) of 0.2 pW/√Hz at 2.5 THz is reported for the superconducting HEBs with thermal biasing. Instead of thermal one, microwave (MW) which was first used to stabilize the HEB mixer is also applied to bias the device as a direct detector. Furthermore, THz can be used to bias the HEBs, if THz sources can be provided easy. Although MW biasing can improve sensitivity of the superconducting HEB direct detectors, little work has been done to compare the responsivity and NEP among the THz direct detectors with thermal, THz and MW biasing. To find a best biasing method, we have studied the similarities and differences of the direct detectors based on the superconducting HEBs with three different biasing methods. The fabricated NbN HEB detectors consist of a complementary logarithmic-spiral antenna made of gold and an NbN film (bridge) connecting across the antenna’s inner terminals. We have fabricated the niobium nitride (NbN) superconducting HEB mixers with the system double sideband (DSB) noise temperature better than 8 times of the quantum limit: hf/kB (where h is the Planck constant, kB is the Boltzmann constant and f is the operating frequency) at the frequencies higher than 1 THz. Here, the mixer chips with the system DSB noise temperature of about 400 K and the intermediate frequency (IF) gain bandwidth (GBW) of larger than 5 GHz at 4.2 K and 0.65 THz have been used. As the direct detectors, the current responsivity of 290 A/W and 105 A/W are obtained for MW and THz biasing, which about one order higher than that of thermal biasing. The NEP of 2.7 pW/√Hz is obtained with MW biasing, which can be expected to be improved in the future.

Next-Generation Spectroscopic Technologies•May 14, 2019•0 citations
The heterodyne mixing and direct detection performance of a superconducting NbN hot-electron bolometer (HEB) integrated with a log-spiral antenna have been thoroughly characterized. The corrected receiver noise temperature and IF gain bandwidth are approximately 800 K at 0.5 THz, 750 K at 0.85 THz and 3 GHz at its optimum bias point. In addition, both the receiver noise temperature and IF gain bandwidth were found insensitive to the bath temperature, while the bias point was fixed, in good agreement with those simulated with the hot-spot model taking account of the HEB's current-dependent resistive transition. Furthermore, the HEB's frequency response was measured by a Fourier transform spectrometer at different bias points and bath temperatures. The estimated noise equivalent power (NEP) was close to 10-13W/Hz0.5around the HEB's transition temperature.
In this paper, the performance of a quasi-optical phonon-cooled NbN superconducting hot electron bolometer (HEB) mixer is thoroughly investigated. The variation of the receiver noise temperature and the conversion gain around 600 GHz with respect to DC bias voltage and LO pumping level has been measured. The lowest receiver noise temperature is 750 K and reduced to about 250 K after correcting the quasi-optical losses before the HEB mixer. We compared the measured results with the predictions according to one dimensional distributed hot spot model. A reasonable match between theoretical model and experiment is observed. In addition, the direct response of the HEB mixer (integrated with a log-periodic spiral antenna) is measured by using Fourier Transform Spectrometer (FTS). The stability of the receiver is also investigated by means of Allan variance time measurements performed with an intermediate frequency (IF) bandwidth of 40 MHz.
NbN hot electron bolometer (HEB) mixers are at this moment the best heterodyne detectors for frequencies above 1 THz. However, the fabrication procedure of these devices is such that the quality of the interface between the NbN superconducting film and the contact structure is not under good control. This results in a contact resistance between the NbN bolometer and the contact pad. We compare identical bolometers, with different NbN - contact pad interfaces, coupled with a spiral antenna. We find that cleaning the NbN interface and adding a thin additional superconductor prior to the gold contact deposition improves the noise temperature and the bandwidth of the HEB mixers with more than a factor of 2. We obtain a DSB noise temperature of 950 K at 2.5 THz and a Gain bandwidth of 5-6 GHz. For use in real receiver systems we design small volume (0.15x1 micron) HEB mixers with a twin slot antenna. We find that these mixers combine good sensitivity (900 K at 1.6 THz) with low LO power requirement, which is 160 - 240 nW at the Si lens of the mixer. This value is larger than expected from the isothermal technique and the known losses in the lens by a factor of 3-3.5.
Heterodyne receivers for applications in astronomy and planetary research need quantum limited sensitivity. In instruments which are currently built for SOFIA and Herschel, superconducting hot electron bolometers (HEB) are used to achieve this goal at frequencies above 1.4 THz. In order to optimize the performance for this frequency of hot electron bolometer mixers with different in-plane dimensions and logarithmic-spiral feed antennas have been investigated. Their noise temperatures and beam patterns were measured. Above 3 THz the best performance was achieved with a superconducting bridge of 2.0/spl times/0.2 /spl mu/m/sup 2/ incorporated in a logarithmic spiral antenna. The DSB noise temperatures were 2700 K, 4700 and 6400 K at 3.1 THz, 4.3 THz and 5.2 THz, respectively. The results demonstrate that the NbN HEB is very well suited as a mixer for THz heterodyne receivers up to at least 5 THz.
We demonstrate that the performance of NbN lattice cooled hot electron bolometer mixers depends strongly on the interface quality between the bolometer and the contact structure. Both the receiver noise temperature and the gain bandwidth can be improved by a factor of 2 by cleaning the interface and adding an additional superconducting interlayer to the contact pad. Using this we obtain a double sideband receiver noise temperature of 950 K at 2.5 THz and 4.3 K, using a 0.4/spl times/4 /spl mu/m HEB mixer with a spiral antenna. At the same bias point, we obtain an IF gain bandwidth of 6 GHz. To comply with current demands on THz mixers for use in space based receivers we reduce the device size to 0.15/spl times/1 /spl mu/m and use a twin slot antenna. We report measurements of the noise temperature, LO power requirement, stability and the direct detection effect, using a mixer with a 1.6 THz twin slot antenna and a 1.462 THz solid state LO source with calibrated output power.
Superconducting hot electron bolometers (HEBs) are widely used as terahertz (THz) heterodyne detectors (mixers) and becoming the most advantageous candidate for low noise receiver at frequencies above 1.2 THz. However, there is still lack of accurate theoretical modeling which explains the complex mechanism of different aspects of superconducting HEBs. These difficulties do not prevent researchers around the world from making experimental progress. In the last few years, superconducting HEBs are also used as THz direct detectors to develop the array for the applications in biology, medicine and security systems. Recently, a noise equivalent power (NEP) of 0.2 pW/√Hz at 2.5 THz is reported for the superconducting HEBs with thermal biasing. Instead of thermal one, microwave (MW) which was first used to stabilize the HEB mixer is also applied to bias the device as a direct detector. Furthermore, THz can be used to bias the HEBs, if THz sources can be provided easy. Although MW biasing can improve sensitivity of the superconducting HEB direct detectors, little work has been done to compare the responsivity and NEP among the THz direct detectors with thermal, THz and MW biasing. To find a best biasing method, we have studied the similarities and differences of the direct detectors based on the superconducting HEBs with three different biasing methods. The fabricated NbN HEB detectors consist of a complementary logarithmic-spiral antenna made of gold and an NbN film (bridge) connecting across the antenna’s inner terminals. We have fabricated the niobium nitride (NbN) superconducting HEB mixers with the system double sideband (DSB) noise temperature better than 8 times of the quantum limit: hf/kB (where h is the Planck constant, kB is the Boltzmann constant and f is the operating frequency) at the frequencies higher than 1 THz. Here, the mixer chips with the system DSB noise temperature of about 400 K and the intermediate frequency (IF) gain bandwidth (GBW) of larger than 5 GHz at 4.2 K and 0.65 THz have been used. As the direct detectors, the current responsivity of 290 A/W and 105 A/W are obtained for MW and THz biasing, which about one order higher than that of thermal biasing. The NEP of 2.7 pW/√Hz is obtained with MW biasing, which can be expected to be improved in the future.