Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Detection of Photomixing Signals With a YBCO Josephson Junction Coupled to a Coplanar Waveguide

Iwao Kawayama, Ryuhei Kinjo, Toshihiko Kiwa, Hironaru Murakami, Masayoshi Tonouchi

Published Jun 1, 2007• 0 citations
Publisher

Abstract

We have fabricated a generation and detection system of photomixing signals using a photomixing technique and a Josephson junction detector. Up to now, an electromagnetic wave generated by a heterodyne mixing of two lasers was emitted from an antenna, and irradiated to a Josephson junction. In this study, we have developed the system, and the photomixing signal was introduced into a coaxial cable and a coplanar wave guide coupled to a Josephson junction. This structure is more suitable for device application since it can easily be integrated into electronic devices. With this system we can clearly observed photomixing signals from 16 GHz to 95 GHz using a uni-traveling-carrier photodiode as a photomixer as well as signals in the range of 14 GHz to 50 GHz using an InGaAs PIN photodiode.

DOI
10.1109/tasc.2007.898106

Related papers

Real-time monitoring of a photomixing signal using a high-TCJosephson junction

Toshihiko Kiwa, Masayoshi Tonouchi

An optical–microwave conversion system has been proposed as a high-stability oscillator in the microwave and millimetre-wave frequency region. A photomixer with heterodyne mixing of two lasers was applied to generate electromagnetic waves and a high-TC grain boundary Josephson junction detector was used to monitor the frequency of the electromagnetic waves in real time. We described the system in detail; it employed a sealed optical connector to introduce the optical signal directly into the cryostat.

Superconductor Science and Technology•Jun 5, 2004•4 citations

Photomixing Optical-Microwave Transformer Coupled with High-TC Josephson Junctions.

Toshihiko Kiwa, Masayoshi Tonouchi

A new type of optical-microwave conversion system has been developed as an interface between optical systems and high-speed electric circuits. The microwave was generated by mixing two optical beams in a photodiode and radiated from a rod antenna, which was placed beside a high-Tc grain boundary Josephson junction detector. Since frequencies of radiated microwaves correspond to the frequency differences between the two optical beams, the wavelength information of the beams is reflected in the current-voltage and differential resistance-voltage properties of the Josephson junction. System operation up to 20 GHz was demonstrated by changing the wavelength of the two beams and the temperature of the Josephson junction. The relation between the frequency differences and measured Shapiro step intervals suggests that the system can be utilized for a highly sensitive optical-microwave conversion.

TEION KOGAKU (Journal of Cryogenics and Superconductivity Society of Japan)•Jan 1, 2003•0 citations

Toward terahertz heterodyne detection with superconducting Josephson junctions

N. Bergeal, M. Malnou, C. Feuillet-Palma +5 more

The terahertz region of the electromagnetic spectrum [0.3-10THz] has, so far, not been exploited fully due to the lack of suitable sources and detectors. Indeed, THz frequency lies between the frequency range of traditional electronics and photonics where the existing technology cannot be simply extended. SIS Niobium tunnel junctions that are currently used as mixing element in heterodyne receivers are intrinsically limited in frequency by the energy gap of Nb and operate only at low temperature (4.2K). An alternative to these devices consists of using High-Tc superconducting receivers. Over the past years, we have developed a new approach based on ion irradiation to make Josephson nano-junctions and SQUIDs with YBCO thin films [1,2]. In this talk, we will present a study of the high-frequency mixing properties of such junctions up to 400 GHz [3]. Conversion gain has been measured at frequencies spanning the range below and above the characteristic frequency fc = (2e/h)IcRn of the junctions. The transition between two distinct mixing regimes has been clearly evidenced, in good agreement with the prediction of the three ports model.[1] N. Bergeal et al., Appl. Phys. Lett. 87, 102502 (2005)[2] N. Bergeal et al., Appl. Phys. Lett. 89, 1112515 (2006)[3] Luo et al, arXiv:1203.1734 (2012)

Bulletin of the American Physical Society•Mar 19, 2013•0 citations

Heterodyne mixing with a sandwich-type Josephson junction using a Bi-based high- oxide superconductor

K Mizuno, Hidetaka Higashino, Kentaro Setsune

A sandwich-type high- Josephson junction coupled with a coplanar-type transmission line was fabricated and heterodyne mixing characteristics were investigated. The junction was fabricated from a stacked film structure of (BSCCO/BSNCO/BSCCO) and the transmission line was made of sputter-deposited Pt film. The junction had a rectangular shape of . Current - voltage (I - V) curves of the junction showed weak-link-type characteristics. Two microwave sources of a frequency synthesizer and a sweep oscillator were used as a local oscillator (LO: 20 GHz) and a radio frequency signal source (RF: 19 GHz) for heterodyne mixing experiments. Intermediate signal (IF: 1 GHz) was transmitted through the transmission line and detected by a power meter. The conversion efficiency of -44 dB was estimated for an LO oscillator level of -23 dB m at 5.7 K when the junction was biased at the point below the first Shapiro step.

Superconductor Science and Technology•Apr 1, 1996•2 citations

Slot Antenna Coupled Thin-Film YBCO Josephson Mixers

Takashi Nozue, Akihisa Hasegawa, Yoshizumi Yasuoka Yamashita

Antenna coupled thin-film Y1Ba2Cu3O7- x Josephson mixers, consisting of a slot antenna on a fused quartz substrate and a YBCO Josephson junction on a MgO substrate, were fabricated and mixing experiments were carried out in the 50 GHz millimeter wave region. The mixing signal (IF output) obtained using the antenna coupled Josephson mixer was 12 dB greater than that obtained using the mixer without the antenna.

Japanese Journal of Applied Physics•Sep 1, 1996•4 citations

Millimeter-wave detection by GBJJ using high-T/sub c/ superconducting YBaCuO films

S. Kita, H. Tanabe, Takeshi Kobayashi

Millimeter-wave detection in the heterodyne mixing mode has been carried out using the high-T/sub c/ superconducting GBJJ (grain boundary Josephson junction). The GBJJ was fabricated from high T/sub c/ superconducting Y-Ba-Cu-O films, prepared on YSZ and SrTiO/sub 3/ substrates using an RF sputtering technique. The junction was patterned by chemical wet etching with phosphoric acid solution. The authors carried out experiments in the heterodyne mixing mode for a signal of 35 GHz with local oscillation at 34.97 GHz. The detected IF (intermediate frequency) output power was obtained at a bias voltage lying midway between the zeroth and first Shapiro steps. A mixer conversion efficiency of -15 dB was obtained with a dynamic range of about 20 dB at 35 GHz. This result strongly implies that high-T/sub c/ superconducting GBJJ works well as a detector at millimeter-wave frequencies.>

IEEE Transactions on Magnetics•Mar 1, 1989•16 citations
We have fabricated a generation and detection system of photomixing signals using a photomixing technique and a Josephson junction detector. Up to now, an electromagnetic wave generated by a heterodyne mixing of two lasers was emitted from an antenna, and irradiated to a Josephson junction. In this study, we have developed the system, and the photomixing signal was introduced into a coaxial cable and a coplanar wave guide coupled to a Josephson junction. This structure is more suitable for device application since it can easily be integrated into electronic devices. With this system we can clearly observed photomixing signals from 16 GHz to 95 GHz using a uni-traveling-carrier photodiode as a photomixer as well as signals in the range of 14 GHz to 50 GHz using an InGaAs PIN photodiode.
An optical–microwave conversion system has been proposed as a high-stability oscillator in the microwave and millimetre-wave frequency region. A photomixer with heterodyne mixing of two lasers was applied to generate electromagnetic waves and a high-TC grain boundary Josephson junction detector was used to monitor the frequency of the electromagnetic waves in real time. We described the system in detail; it employed a sealed optical connector to introduce the optical signal directly into the cryostat.
A new type of optical-microwave conversion system has been developed as an interface between optical systems and high-speed electric circuits. The microwave was generated by mixing two optical beams in a photodiode and radiated from a rod antenna, which was placed beside a high-Tc grain boundary Josephson junction detector. Since frequencies of radiated microwaves correspond to the frequency differences between the two optical beams, the wavelength information of the beams is reflected in the current-voltage and differential resistance-voltage properties of the Josephson junction. System operation up to 20 GHz was demonstrated by changing the wavelength of the two beams and the temperature of the Josephson junction. The relation between the frequency differences and measured Shapiro step intervals suggests that the system can be utilized for a highly sensitive optical-microwave conversion.
The terahertz region of the electromagnetic spectrum [0.3-10THz] has, so far, not been exploited fully due to the lack of suitable sources and detectors. Indeed, THz frequency lies between the frequency range of traditional electronics and photonics where the existing technology cannot be simply extended. SIS Niobium tunnel junctions that are currently used as mixing element in heterodyne receivers are intrinsically limited in frequency by the energy gap of Nb and operate only at low temperature (4.2K). An alternative to these devices consists of using High-Tc superconducting receivers. Over the past years, we have developed a new approach based on ion irradiation to make Josephson nano-junctions and SQUIDs with YBCO thin films [1,2]. In this talk, we will present a study of the high-frequency mixing properties of such junctions up to 400 GHz [3]. Conversion gain has been measured at frequencies spanning the range below and above the characteristic frequency fc = (2e/h)IcRn of the junctions. The transition between two distinct mixing regimes has been clearly evidenced, in good agreement with the prediction of the three ports model.[1] N. Bergeal et al., Appl. Phys. Lett. 87, 102502 (2005)[2] N. Bergeal et al., Appl. Phys. Lett. 89, 1112515 (2006)[3] Luo et al, arXiv:1203.1734 (2012)
A sandwich-type high- Josephson junction coupled with a coplanar-type transmission line was fabricated and heterodyne mixing characteristics were investigated. The junction was fabricated from a stacked film structure of (BSCCO/BSNCO/BSCCO) and the transmission line was made of sputter-deposited Pt film. The junction had a rectangular shape of . Current - voltage (I - V) curves of the junction showed weak-link-type characteristics. Two microwave sources of a frequency synthesizer and a sweep oscillator were used as a local oscillator (LO: 20 GHz) and a radio frequency signal source (RF: 19 GHz) for heterodyne mixing experiments. Intermediate signal (IF: 1 GHz) was transmitted through the transmission line and detected by a power meter. The conversion efficiency of -44 dB was estimated for an LO oscillator level of -23 dB m at 5.7 K when the junction was biased at the point below the first Shapiro step.
Millimeter-wave detection in the heterodyne mixing mode has been carried out using the high-T/sub c/ superconducting GBJJ (grain boundary Josephson junction). The GBJJ was fabricated from high T/sub c/ superconducting Y-Ba-Cu-O films, prepared on YSZ and SrTiO/sub 3/ substrates using an RF sputtering technique. The junction was patterned by chemical wet etching with phosphoric acid solution. The authors carried out experiments in the heterodyne mixing mode for a signal of 35 GHz with local oscillation at 34.97 GHz. The detected IF (intermediate frequency) output power was obtained at a bias voltage lying midway between the zeroth and first Shapiro steps. A mixer conversion efficiency of -15 dB was obtained with a dynamic range of about 20 dB at 35 GHz. This result strongly implies that high-T/sub c/ superconducting GBJJ works well as a detector at millimeter-wave frequencies.>