Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Sensors and Actuators A Physical

Multi-layer atom chips for atom tunneling experiments near the chip surface

Ho‐Chiao Chuang, Evan A. Salim, Vladan Vuletić, Dana Z. Anderson, Victor M. Bright

Published Jan 19, 2010• 13 citations
Publisher
DOI
10.1016/j.sna.2010.01.003

Related papers

Relevance of sub-surface chip layers for the lifetime of magnetically trapped atoms

B. Zhang, Carsten Henkel, Elmar Haller +4 more

The European Physical Journal D•Aug 1, 2005•25 citations

Fabrication of an Atom Chip for Studying Atom-Surface Interactions.

Owen Cherry, Jeff Carter, Czang-Ho Lee +2 more

Bulletin of the American Physical Society•May 17, 2006•0 citations

Development, Fabrication and Characterisation of Atom Chips

S. Groth

Atom chips are robust and extremely powerful toolboxes for quantum optical experiments, since they make it possible to create exceedingly precise magnetic traps for neutral atoms with minimal field modulations. Accurate manipulation of trapped atoms is feasible with magnetic and electric fields created on the atom chip. Therefore atom chips with high quality surfaces and extremely well defined wires were build (roughness < 20nm). Furthermore new generations of atom chips were developed, like the multi-layer atom chip with contact-free wire crossings, the sub-micron structured atom chip and the semiconducting atom chip. Extensive characterisation measurements of atom chip wires demonstrated that the wires stand current densities of up to 10^7A/cm^2 for seconds and voltage differences of more than 500V over 10µm. From the different materials tested doped silicon with a thin silicon dioxide layer is the best qualified substrate for atom chip fabrication. The atom chips fabricated during this thesis have been used in many successful experiments, yielding numerous results. Moreover this thesis established the basics for many further experiments in atom physics and quantum optics and delivers complete instructions for the fabrication of all developed atom chips as well as an introduction to the experiments.

•Jan 1, 2006•4 citations

An atom chip for studying interactions between atoms and metal surfaces

J.D. Carter, Owen Cherry, J.D.D. Martin

Bulletin of the American Physical Society•Jun 7, 2007•0 citations

Design, microfabrication and characterization of planarized multilayer atom chips with enhanced heat dissipation

Ho‐Chiao Chuang, Chung-Wen Weng, Hsiang-Fu Li

This paper describes the design and fabrication of planarized multilayer atom chips for an ultrahigh-vacuum system in atomic physics experiments. A fabrication process is developed to define micrometer-scale wire patterns on a silicon substrate and wires are plated by copper electroplating. SU-8 is chosen as the isolation layer between the upper and bottom wires, and its thickness, surface flatness and surface roughness (Ra = 5 nm) are controlled by the chemical–mechanical planarization process. A reflectivity of nearly 90% is measured on the chip surface; thus, the former method of attaching a silver mirror is unnecessary (Du et al 2004 Phys. Rev. A 70 053606). A heat dissipation copper block is incorporated in our chip design to increase the sustainable current densities of upper wires of more than 3.8 × 105 A cm−2. Results show the improvement of 55.74%, compared with the nonheat dissipation design (2.44 × 105 A cm−2), and thus meeting the requirements for chip-based atom trapping experiments.

Journal of Micromechanics and Microengineering•Nov 3, 2011•8 citations

Single-layer atom chip for continuous operation: Design, fabrication and performance

Anton E. Afanasiev, Alexey S. Kalmykov, Roman V. Kirtaev +4 more

Optics & Laser Technology•Nov 27, 2021•20 citations
Atom chips are robust and extremely powerful toolboxes for quantum optical experiments, since they make it possible to create exceedingly precise magnetic traps for neutral atoms with minimal field modulations. Accurate manipulation of trapped atoms is feasible with magnetic and electric fields created on the atom chip. Therefore atom chips with high quality surfaces and extremely well defined wires were build (roughness < 20nm). Furthermore new generations of atom chips were developed, like the multi-layer atom chip with contact-free wire crossings, the sub-micron structured atom chip and the semiconducting atom chip. Extensive characterisation measurements of atom chip wires demonstrated that the wires stand current densities of up to 10^7A/cm^2 for seconds and voltage differences of more than 500V over 10µm. From the different materials tested doped silicon with a thin silicon dioxide layer is the best qualified substrate for atom chip fabrication. The atom chips fabricated during this thesis have been used in many successful experiments, yielding numerous results. Moreover this thesis established the basics for many further experiments in atom physics and quantum optics and delivers complete instructions for the fabrication of all developed atom chips as well as an introduction to the experiments.
This paper describes the design and fabrication of planarized multilayer atom chips for an ultrahigh-vacuum system in atomic physics experiments. A fabrication process is developed to define micrometer-scale wire patterns on a silicon substrate and wires are plated by copper electroplating. SU-8 is chosen as the isolation layer between the upper and bottom wires, and its thickness, surface flatness and surface roughness (Ra = 5 nm) are controlled by the chemical–mechanical planarization process. A reflectivity of nearly 90% is measured on the chip surface; thus, the former method of attaching a silver mirror is unnecessary (Du et al 2004 Phys. Rev. A 70 053606). A heat dissipation copper block is incorporated in our chip design to increase the sustainable current densities of upper wires of more than 3.8 × 105 A cm−2. Results show the improvement of 55.74%, compared with the nonheat dissipation design (2.44 × 105 A cm−2), and thus meeting the requirements for chip-based atom trapping experiments.