Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Softwaretechnik-Trends

Receiver Measurements at 700 GHz with a Niobium Diffusion-Cooled Hot-Electron Bolometer Mixer

D. Wilms Floet, J. R. Gao, T. M. Klapwijk, W. F. M. Ganzevles, Gert J. de Lange, Piet A. J. de Korte

Published Mar 1, 1999• 1 citation
OpenAlex

Abstract

We report on heterodyne measurements with a Nb diffusion-cooled hot-electron bolometer in a fixed tuned waveguide mixer at 700 GHz. The device is a 300 nm long and 12 nm thick Nb microbridge, with a normal state resistance of 31 Si. We have measured the DSB receiver noise temperature using a standard Y-factor method with a 300 K and 77 K blackbody load. At 700 GHz, a bath temperature of 4.3 K, and an intermediate frequency of 1.25 GHz, the receiver noise temperature Tre, ,DsB is 1690 K after correction for the losses in the beamsplitter. Reducing the bath temperature to 3.3 K decreases Trec.Dsg to 1100 K. Careful inspection of the pumped differential I(V) characteristics does not reveal any influence due to direct detection. From the data we extract a maximum value of —17.8 dB for the conversion gain of the mixer at 4.3 K. The minimum mixer noise is determined to be 1170 K by applying a noise breakdown calculation. We expect significant improvement of the receiver noise performance upon further reduction of the bath temperature.

Related papers

Large bandwidth and low noise in a diffusion-cooled hot-electron bolometer mixer

Anders J. Skalare, William R. McGrath, B. Bumble +5 more

Heterodyne measurements have been made at 533 GHz using a novel superconducting hot-electron bolometer in a waveguide mixer. The bolometer is a 0.3 μm long niobium microbridge with a superconducting transition temperature of 5 K. The short length ensures that electron diffusion dominates over electron-phonon interactions as the electron cooling mechanism, which should allow heterodyne detection with intermediate frequencies (if) of several GHz. A Y-factor response of 1.15 dB has been obtained at an if of 1.4 GHz with 77 and 295 K loads, indicating a receiver noise temperature of 650 K DSB. The −3 dB rolloff in the if response occurs at 1.7 GHz.

Applied Physics Letters•Mar 11, 1996•73 citations

A heterodyne receiver at 533 GHz using a diffusion-cooled superconducting hot electron bolometer mixer

Anders J. Skalare, William R. McGrath, B. Bumble +4 more

This paper describes heterodyne measurements at 533 GHz using a novel superconducting hot electron bolometer in a waveguide mixer block. The bolometer is a thin (10 nm) and narrow (0.1 /spl mu/m) strip of niobium with a length of less than half a micron and a critical temperature of approximately 5.5 K. The short length ensures that diffusion dominates over electron-phonon interaction as a cooling mechanism for the hot electrons, thus allowing heterodyne detection with intermediate frequencies of several GHz. A Y-factor response of 1.15 dB has been obtained at an intermediate frequency of 1.4 GHz with hot/cold load temperatures of approximately 295/77 K, indicating a receiver noise temperature around 650 K DSB. The IF response extends up to at least 2 GHz and possibly higher.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•32 citations

Measurements with a Diffusion-Cooled Nb Hot-Electron Bolometer Mixer at 1100 GHz

Anders J. Skalare, William R. McGrath, B. Bumble +1 more

In this paper we report receiver sensitivity measurements with a diffusion-cooled niobium hot-electron bolometer around 1100 GHz. The lowest receiver noise temperature was 1670 K DSB, with approximately 40 nW of local oscillator power being dissipated in the device. The intermediate frequency bandwidth of this device, due to its short length (0.15 gm) and low normal resistance (43 a), exceeded the 1.8 GHz bandwidth of the measurement setup. The receiver was used to detect the sulfur dioxide gas absorption line at 1102 GHz in a heterodyne mode.

•Mar 1, 1998•9 citations

Fabrication and characterisation of a Nb diffusion-cooled hot electron bolometer for a 730 GHz waveguide mixer

D. Wilms Floet, No Value Gao, W. Hulshoff +3 more

We have fabricated Nb diffusion-cooled hot electron bolometers for a waveguide mixer around 700 GHz. The device in this work is a thin (12 nm) Nb bridge with a length and width of 220 nm and is defined by a two-step electron beam lithography process. The resistance as a function of temperature shows two transitions, which we attribute to the Nb bridge (6.1 K) and to parts of the Nb which are covered by the Au pads (5.4 K). We have measured a DSB receiver noise temperature of 2200 K at 735 GHz and a bath temperature of 3.3 K. No significant increase of the noise temperature is observed at IF frequencies between 1.1 and 1.7 GHz. The coupled LO power is estimated to be 35 nW.

•Jan 1, 1997•0 citations

Diffusion-cooled superconducting hot electron bolometer heterodyne mixer between 630 and 820 GHz

Klaus Fiegle, D. Diehl, Karl Jacobs

We report on heterodyne mixing experiments between 630-820 GHz using a diffusion-cooled superconducting hot electron bolometer at intermediate frequencies from 1-2 GHz. The niobium bolometer which is cooled by diffusion of the hot electrons into a normal conductor has dimensions of 0.3 /spl mu/m/spl times/0.15 /spl mu/m and was fabricated at KOSMA with a two-step electron beam lithography process. The film thickness of the device is 30 nm with T/sub c/ of 6.1 K and /spl Delta/T/sub c/ of 0.7 K. The mixing experiments are performed with a tunerless waveguide mixer block previously used for very low-noise SIS receivers. At a physical temperature of 2.2 K, receiver noise temperatures at 666 GHz are 1500 K at 1.0 GHz intermediate frequency, increasing rapidly above 1.5 GHz. The dissipated local oscillator power is evaluated to be 65-90 nW.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•13 citations

Heterodyne mixing in diffusion-cooled superconducting aluminum hot-electron bolometers

Irfan A. Siddiqi, A. Verevkin, D. E. Prober +4 more

We present microwave (30 GHz) measurements on aluminum superconducting hot-electron bolometer (HEB) mixers. Aluminum HEB mixers have a lower superconducting transition temperature than niobium and niobium nitride devices, and are predicted to have improved sensitivity and require less local oscillator power. The devices studied consist of a narrow superconducting aluminum microbridge with contacts comprised of thick aluminum, titanium, and gold. A perpendicular magnetic field is used to suppress superconductivity in the contacts. The device length is much shorter than the electron–phonon inelastic length [L≪(Dτe–ph)1/2] and thus the intermediate frequency (IF) bandwidth is set by the diffusion time of hot electrons from the microbridge into the contacts. We discuss limitations on the IF bandwidth in very short HEB mixers with fully normal contacts. Overall, the microwave heterodyne mixing results show good performance with a mixer noise temperature inferred from the conversion efficiency and output noise of TM⩾4 K, double side band (DSB). Measurements at 618 GHz yield a conversion efficiency approximately 10 dB lower than observed at 30 GHz. Output saturation by background radiation is postulated to contribute significantly to this difference. A similar decrease in conversion efficiency in the microwave mixing measurements is observed when broadband noise is added to the rf input signal. We discuss the tradeoff between increased sensitivity and the occurrence of saturation effects in low transition temperature HEBs.

Journal of Applied Physics•Apr 1, 2002•14 citations
We report on heterodyne measurements with a Nb diffusion-cooled hot-electron bolometer in a fixed tuned waveguide mixer at 700 GHz. The device is a 300 nm long and 12 nm thick Nb microbridge, with a normal state resistance of 31 Si. We have measured the DSB receiver noise temperature using a standard Y-factor method with a 300 K and 77 K blackbody load. At 700 GHz, a bath temperature of 4.3 K, and an intermediate frequency of 1.25 GHz, the receiver noise temperature Tre, ,DsB is 1690 K after correction for the losses in the beamsplitter. Reducing the bath temperature to 3.3 K decreases Trec.Dsg to 1100 K. Careful inspection of the pumped differential I(V) characteristics does not reveal any influence due to direct detection. From the data we extract a maximum value of —17.8 dB for the conversion gain of the mixer at 4.3 K. The minimum mixer noise is determined to be 1170 K by applying a noise breakdown calculation. We expect significant improvement of the receiver noise performance upon further reduction of the bath temperature.
Heterodyne measurements have been made at 533 GHz using a novel superconducting hot-electron bolometer in a waveguide mixer. The bolometer is a 0.3 μm long niobium microbridge with a superconducting transition temperature of 5 K. The short length ensures that electron diffusion dominates over electron-phonon interactions as the electron cooling mechanism, which should allow heterodyne detection with intermediate frequencies (if) of several GHz. A Y-factor response of 1.15 dB has been obtained at an if of 1.4 GHz with 77 and 295 K loads, indicating a receiver noise temperature of 650 K DSB. The −3 dB rolloff in the if response occurs at 1.7 GHz.
This paper describes heterodyne measurements at 533 GHz using a novel superconducting hot electron bolometer in a waveguide mixer block. The bolometer is a thin (10 nm) and narrow (0.1 /spl mu/m) strip of niobium with a length of less than half a micron and a critical temperature of approximately 5.5 K. The short length ensures that diffusion dominates over electron-phonon interaction as a cooling mechanism for the hot electrons, thus allowing heterodyne detection with intermediate frequencies of several GHz. A Y-factor response of 1.15 dB has been obtained at an intermediate frequency of 1.4 GHz with hot/cold load temperatures of approximately 295/77 K, indicating a receiver noise temperature around 650 K DSB. The IF response extends up to at least 2 GHz and possibly higher.>
In this paper we report receiver sensitivity measurements with a diffusion-cooled niobium hot-electron bolometer around 1100 GHz. The lowest receiver noise temperature was 1670 K DSB, with approximately 40 nW of local oscillator power being dissipated in the device. The intermediate frequency bandwidth of this device, due to its short length (0.15 gm) and low normal resistance (43 a), exceeded the 1.8 GHz bandwidth of the measurement setup. The receiver was used to detect the sulfur dioxide gas absorption line at 1102 GHz in a heterodyne mode.
We have fabricated Nb diffusion-cooled hot electron bolometers for a waveguide mixer around 700 GHz. The device in this work is a thin (12 nm) Nb bridge with a length and width of 220 nm and is defined by a two-step electron beam lithography process. The resistance as a function of temperature shows two transitions, which we attribute to the Nb bridge (6.1 K) and to parts of the Nb which are covered by the Au pads (5.4 K). We have measured a DSB receiver noise temperature of 2200 K at 735 GHz and a bath temperature of 3.3 K. No significant increase of the noise temperature is observed at IF frequencies between 1.1 and 1.7 GHz. The coupled LO power is estimated to be 35 nW.
We report on heterodyne mixing experiments between 630-820 GHz using a diffusion-cooled superconducting hot electron bolometer at intermediate frequencies from 1-2 GHz. The niobium bolometer which is cooled by diffusion of the hot electrons into a normal conductor has dimensions of 0.3 /spl mu/m/spl times/0.15 /spl mu/m and was fabricated at KOSMA with a two-step electron beam lithography process. The film thickness of the device is 30 nm with T/sub c/ of 6.1 K and /spl Delta/T/sub c/ of 0.7 K. The mixing experiments are performed with a tunerless waveguide mixer block previously used for very low-noise SIS receivers. At a physical temperature of 2.2 K, receiver noise temperatures at 666 GHz are 1500 K at 1.0 GHz intermediate frequency, increasing rapidly above 1.5 GHz. The dissipated local oscillator power is evaluated to be 65-90 nW.
We present microwave (30 GHz) measurements on aluminum superconducting hot-electron bolometer (HEB) mixers. Aluminum HEB mixers have a lower superconducting transition temperature than niobium and niobium nitride devices, and are predicted to have improved sensitivity and require less local oscillator power. The devices studied consist of a narrow superconducting aluminum microbridge with contacts comprised of thick aluminum, titanium, and gold. A perpendicular magnetic field is used to suppress superconductivity in the contacts. The device length is much shorter than the electron–phonon inelastic length [L≪(Dτe–ph)1/2] and thus the intermediate frequency (IF) bandwidth is set by the diffusion time of hot electrons from the microbridge into the contacts. We discuss limitations on the IF bandwidth in very short HEB mixers with fully normal contacts. Overall, the microwave heterodyne mixing results show good performance with a mixer noise temperature inferred from the conversion efficiency and output noise of TM⩾4 K, double side band (DSB). Measurements at 618 GHz yield a conversion efficiency approximately 10 dB lower than observed at 30 GHz. Output saturation by background radiation is postulated to contribute significantly to this difference. A similar decrease in conversion efficiency in the microwave mixing measurements is observed when broadband noise is added to the rf input signal. We discuss the tradeoff between increased sensitivity and the occurrence of saturation effects in low transition temperature HEBs.