Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Magnetics

Coherent effects in series arrays of proximity effect superconducting bridges

D. Palmer, James E. Mercereau

Published Mar 1, 1975• 26 citations
Publisher

Abstract

Planar series arrays of up to 500 proximity effect superconducting bridges have been fabricated with sufficient uniformity to respond coherently to incident radiation (10-20,000MHz) without separate biasing. By varying the geometry, resistance for the arrays can range from .1-50Ω. Despite this high total impedance, low frequency coherent response to external radiation is limited only by single bridge voltage noise. Low frequency (30-500MHz) coherent internal voltage oscillations of current biased arrays have been detected and confirm that the oscillating voltage signal grows linearly in bridge number while the voltage noise increases only as the square root. An array of n elements responds to incident high frequency radiation in first approximation as though it were a simple Josephson junction but quantized in units of n(h/2e). Coincident operation to high frequency depends strongly on small (\leq 1\mu) bridge separation. High resistance, coincident operation, and exponential dependence of critical current on temperature make these arrays good candidates for voltage standards, coherent and bolometric radiation detectors, and cryogenic rf sources.

DOI
10.1109/tmag.1975.1058687

Related papers

dc responsivity of proximity effect bridges to high frequency radiation

M. G. Hauser, David William Palmer

The effect of microwave radiation on the dc current-voltage characteristic of proximity effect bridges has been studied at frequencies of 10, 35 and 90 GHz. We report the properties of bridges fabricated in layered films of Nb and Ta. The fraction ε of the incident radiant power absorbed by the bridge is measured calorimetrically, permitting determination of the intrinsic responsivity (volts per watt of power absorbed when operated in a current-biased mode). In our test geometry ε is typically ˜ 10⁻⁴ for a 0.1 Ω Nb-Ta bridge, and increases roughly linearly with dc junction resistance R. Broad-band responsivitv is generally independent of incident power. increases with increasing critical current Ic (decreasing temperature), and decreases with increasing frequency, varying approximately as Ω-3 where Ω is the normalized frequency ħω/2 eRIc. Peak responsivities achieved to date are ˜ 105 V/W (absorbed) at 10 GHz and ˜ 102 V/W (absorbed) at 90 GHz. By mounting junctions in vacuum and exposing them to near-infrared radiation, we have found that their purely bolometric (thermal) response is much weaker than the microwave response at 90 GHz.

Revue de Physique Appliquée•Jan 1, 1974•7 citations

Coherent effects in large arrays of superconducting bridges

David William Palmer, James E. Mercereau

Series arrays of nearly identical superconducting proximity effect bridges have been fabricated in Nb/Ta thin films. Arrays with up to 500 bridges respond cooperatively to incident radiation and produce voltage steps in response to incident 30–20 000-MHz radiation at V =(number of bridges in array)×(hν/2e).

Applied Physics Letters•Oct 15, 1974•28 citations

I. The phase-current relation at zero voltage in proximity effect bridges. II. The interaction of proximity effect bridges with superconducting microstrip resonators

Tomas Ganz

Experimental investigations on the proximity effect bridge (a Josephson device) at zero voltage and at finite voltages in the µV range are reported. The phase-super current relation at zero voltage was measured using an asymmetric superconducting quantum interferormeter circuit. The data are in agreement with the Josephson supercurrent-phase relation I_S=I_C sinδ with deviation less than 5% of the critical current I_c. The supercurrent density in the measured bridges reached as high as 50-100 µA/µm^2. Using microcircuitry techniques, proximity effect bridges were strongly coupled to superconducting microstrip resonators. Selfinduced steps in the I-V characteristics of bridges coupled to resonators were observed in the GHz region at voltages (frequencies) corresponding to the expected modes of the resonators. Two types of steps were seen depending on whether the resonator impedance on resonance was much higher or much smaller than the bridge resistance. A simple two fluid model of the bridge-resonator circuit was developed and the size and shape of self-induced steps were calculated for a generalized Josephson oscillator relation I_S = I_c(l-q + q sin∫ 2e/hV dt) where q = 1 corresponds to the original Josephson relation and q = 1/2 represents the phase slip regime. At low critical currents (I_c < 10 µA) and low voltages (V < 3µV) the size and shape of experimentally observed self-induced steps agree with the q = 1 model. At higher voltages and/or critical currents the step size increasingly deviates from the q = 1 model towards q = 1/2. These observations are interpreted to indicate a progressive reduction of the amplitude of the oscillating Josephson supercurrent in proximity effect bridges from I_c towards I_c /2 as the critical current and/or voltage are increased.

•Dec 6, 2011•0 citations

Microwave coupling of frequency-locked Josephson junction arrays

Insang Song, Yongheum Eom, Gwangseo Park +2 more

A high temperature superconducting YBa2Cu3Oy array of five Josephson junctions designed with additional coupling lines has been developed to demonstrate the effects of frequency locking and impedance matching for applications such as oscillators, mixers, and detectors. The Josephson self-radiation power was directly detected by a superheterodyne receiver, and Shapiro steps were also measured. The Josephson self-radiation properties reveal good quality of phase locking and microwave coupling with external circuits. The maximum self-radiation power of our array is about 50 pW which is several ten times higher than that of a single Josephson junction, and its peak point exactly satisfies the Josephson current-voltage relation. The Shapiro-step measurements show that the behavior of current-voltage curve depends on the effective inductance of coupling lines which affects the total impedance of Josephson junction array and microwave coupling. The Josephson oscillation frequency was obtained up to about 880 GHz which is 73% of the maximum available frequency calculated from the characteristic voltage of the Josephson junctions. Experimental results show that this type of Josephson junction array can improve the Josephson self-radiation power and increase the maximum detectable frequency.

Applied Physics Letters•Jun 16, 1997•8 citations

Superconducting microbridges and arrays

P. E. Lindelof, Jørn Bindslev Hansen, P. Jespersen

The current‐voltage characteristics and Josephson radiation have been studied for a number of indium bridges as a function of temperatures. Our results show strong deviations from the predictions of the RSJ model, even in the temperature regime where the bridge size is smaller than the coherence length. We ascribe this to non‐equilibrium effects in the around the microbridge.In order to improve the applicability of the Josephson effect, we have investigated coherent arrays of 2, 4 and 10 microbridges. The 10 microbridge array is a novel design which allows the bridges to be parallel‐biased at dc (equal voltages) and series‐biased at 9 GHz (high output impedance).

AIP conference proceedings•Jan 1, 1978•3 citations

Superconducting noise bolometer with microwave bias and readout for array applications

Artem A. Kuzmin, Alexei D. Semenov, S. V. Shitov +4 more

We present a superconducting noise bolometer for terahertz radiation, which is suitable for large-format arrays. It is based on an antenna-coupled superconducting micro-bridge embedded in a high-quality factor superconducting resonator for a microwave bias and readout with frequency-division multiplexing in the GHz range. The micro-bridge is kept below its critical temperature and biased with a microwave current of slightly lower amplitude than the critical current of the micro-bridge. The response of the detector is the rate of superconducting fluctuations, which depends exponentially on the concentration of quasiparticles in the micro-bridge. Excess quasiparticles are generated by an incident THz signal. Since the quasiparticle lifetime increases exponentially at lower operation temperature, the noise equivalent power rapidly decreases. This approach allows for large arrays of noise bolometers operating above 1 K with sensitivity, limited by 300-K background noise. Moreover, the response of the bolometer always dominates the noise of the readout due to relatively large amplitude of the bias current. We performed a feasibility study on a proof-of-concept device with a 1.0 × 0.5 μm2 micro-bridge from a 9-nm thin Nb film on a sapphire substrate. Having a critical temperature of 5.8 K, it operates at 4.2 K and is biased at the frequency 5.6 GHz. For the quasioptical input at 0.65 THz, we measured the noise equivalent power ≈3 × 10−12 W/Hz1/2, which is close to expectations for this particular device in the noise-response regime.

arXiv:1709.02997•Applied Physics Letters•Jul 24, 2017•8 citations
Planar series arrays of up to 500 proximity effect superconducting bridges have been fabricated with sufficient uniformity to respond coherently to incident radiation (10-20,000MHz) without separate biasing. By varying the geometry, resistance for the arrays can range from .1-50Ω. Despite this high total impedance, low frequency coherent response to external radiation is limited only by single bridge voltage noise. Low frequency (30-500MHz) coherent internal voltage oscillations of current biased arrays have been detected and confirm that the oscillating voltage signal grows linearly in bridge number while the voltage noise increases only as the square root. An array of n elements responds to incident high frequency radiation in first approximation as though it were a simple Josephson junction but quantized in units of n(h/2e). Coincident operation to high frequency depends strongly on small (\leq 1\mu) bridge separation. High resistance, coincident operation, and exponential dependence of critical current on temperature make these arrays good candidates for voltage standards, coherent and bolometric radiation detectors, and cryogenic rf sources.
The effect of microwave radiation on the dc current-voltage characteristic of proximity effect bridges has been studied at frequencies of 10, 35 and 90 GHz. We report the properties of bridges fabricated in layered films of Nb and Ta. The fraction ε of the incident radiant power absorbed by the bridge is measured calorimetrically, permitting determination of the intrinsic responsivity (volts per watt of power absorbed when operated in a current-biased mode). In our test geometry ε is typically ˜ 10⁻⁴ for a 0.1 Ω Nb-Ta bridge, and increases roughly linearly with dc junction resistance R. Broad-band responsivitv is generally independent of incident power. increases with increasing critical current Ic (decreasing temperature), and decreases with increasing frequency, varying approximately as Ω-3 where Ω is the normalized frequency ħω/2 eRIc. Peak responsivities achieved to date are ˜ 105 V/W (absorbed) at 10 GHz and ˜ 102 V/W (absorbed) at 90 GHz. By mounting junctions in vacuum and exposing them to near-infrared radiation, we have found that their purely bolometric (thermal) response is much weaker than the microwave response at 90 GHz.
Experimental investigations on the proximity effect bridge (a Josephson device) at zero voltage and at finite voltages in the µV range are reported. The phase-super current relation at zero voltage was measured using an asymmetric superconducting quantum interferormeter circuit. The data are in agreement with the Josephson supercurrent-phase relation I_S=I_C sinδ with deviation less than 5% of the critical current I_c. The supercurrent density in the measured bridges reached as high as 50-100 µA/µm^2. Using microcircuitry techniques, proximity effect bridges were strongly coupled to superconducting microstrip resonators. Selfinduced steps in the I-V characteristics of bridges coupled to resonators were observed in the GHz region at voltages (frequencies) corresponding to the expected modes of the resonators. Two types of steps were seen depending on whether the resonator impedance on resonance was much higher or much smaller than the bridge resistance. A simple two fluid model of the bridge-resonator circuit was developed and the size and shape of self-induced steps were calculated for a generalized Josephson oscillator relation I_S = I_c(l-q + q sin∫ 2e/hV dt) where q = 1 corresponds to the original Josephson relation and q = 1/2 represents the phase slip regime. At low critical currents (I_c < 10 µA) and low voltages (V < 3µV) the size and shape of experimentally observed self-induced steps agree with the q = 1 model. At higher voltages and/or critical currents the step size increasingly deviates from the q = 1 model towards q = 1/2. These observations are interpreted to indicate a progressive reduction of the amplitude of the oscillating Josephson supercurrent in proximity effect bridges from I_c towards I_c /2 as the critical current and/or voltage are increased.
A high temperature superconducting YBa2Cu3Oy array of five Josephson junctions designed with additional coupling lines has been developed to demonstrate the effects of frequency locking and impedance matching for applications such as oscillators, mixers, and detectors. The Josephson self-radiation power was directly detected by a superheterodyne receiver, and Shapiro steps were also measured. The Josephson self-radiation properties reveal good quality of phase locking and microwave coupling with external circuits. The maximum self-radiation power of our array is about 50 pW which is several ten times higher than that of a single Josephson junction, and its peak point exactly satisfies the Josephson current-voltage relation. The Shapiro-step measurements show that the behavior of current-voltage curve depends on the effective inductance of coupling lines which affects the total impedance of Josephson junction array and microwave coupling. The Josephson oscillation frequency was obtained up to about 880 GHz which is 73% of the maximum available frequency calculated from the characteristic voltage of the Josephson junctions. Experimental results show that this type of Josephson junction array can improve the Josephson self-radiation power and increase the maximum detectable frequency.
The current‐voltage characteristics and Josephson radiation have been studied for a number of indium bridges as a function of temperatures. Our results show strong deviations from the predictions of the RSJ model, even in the temperature regime where the bridge size is smaller than the coherence length. We ascribe this to non‐equilibrium effects in the around the microbridge.In order to improve the applicability of the Josephson effect, we have investigated coherent arrays of 2, 4 and 10 microbridges. The 10 microbridge array is a novel design which allows the bridges to be parallel‐biased at dc (equal voltages) and series‐biased at 9 GHz (high output impedance).
We present a superconducting noise bolometer for terahertz radiation, which is suitable for large-format arrays. It is based on an antenna-coupled superconducting micro-bridge embedded in a high-quality factor superconducting resonator for a microwave bias and readout with frequency-division multiplexing in the GHz range. The micro-bridge is kept below its critical temperature and biased with a microwave current of slightly lower amplitude than the critical current of the micro-bridge. The response of the detector is the rate of superconducting fluctuations, which depends exponentially on the concentration of quasiparticles in the micro-bridge. Excess quasiparticles are generated by an incident THz signal. Since the quasiparticle lifetime increases exponentially at lower operation temperature, the noise equivalent power rapidly decreases. This approach allows for large arrays of noise bolometers operating above 1 K with sensitivity, limited by 300-K background noise. Moreover, the response of the bolometer always dominates the noise of the readout due to relatively large amplitude of the bias current. We performed a feasibility study on a proof-of-concept device with a 1.0 × 0.5 μm2 micro-bridge from a 9-nm thin Nb film on a sapphire substrate. Having a critical temperature of 5.8 K, it operates at 4.2 K and is biased at the frequency 5.6 GHz. For the quasioptical input at 0.65 THz, we measured the noise equivalent power ≈3 × 10−12 W/Hz1/2, which is close to expectations for this particular device in the noise-response regime.