Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Study of LR-Loading Technique for Low-Power Single Flux Quantum Circuits

Yuki Yamanashi, T. Nishigai, Nobuyuki Yoshikawa

Published Jun 1, 2007• 59 citations
Publisher

Abstract

A single-flux-quantum (SFQ) circuit is thought to be very suitable as a peripheral circuit for superconducting quantum bits (qubits), which can manipulate and detect the qubit state at a temperature state similar to qubits. Even though the power consumption of SFQ circuits is extremely small, it is still sufficient to heat the substrate at a temperature below 1 K. We have investigated and demonstrated low-power SFQ circuits for this application, using the LR-loading technique, which can reduce the static power consumption of the SFQ circuits. Simulation results show that the ratio of the switching speed to the time constant of the bias circuit is important for the stable operation of low-power SFQ circuits. The static power consumption of SFQ circuits can be reduced to the same order as the dynamic power consumption through optimization of the circuit parameters. We have designed and tested a low-power SFQ clock generator using the LR-loading technique and confirmed its stable operation at 4.2 K, where the power consumption is reduced by 93% compared with ordinary biased circuits.

DOI
10.1109/tasc.2007.898608

Related papers

High-speed demonstration of low-power 1 k-bit shift-register memories using LR-biasing SFQ circuits

Toshihiro Takahashi, Ryo Numaguchi, Yuki Yamanashi +1 more

We designed a low-power shift-register memory using single-flux-quantum (SFQ) circuits for bit-serial SFQ microprocessors. In order to reduce the static power consumption of the SFQ memories, LR-biasing SFQ circuits were employed, where the resistance network for supplying the bias current is replaced with the inductance network with small resistance. We implemented a low-power 1 k-bit SFQ shift-register memory and confirmed its 30 GHz operation for all addresses. The power consumption was reduced to 26% of the conventional resistively biased SFQ memories.

IEICE Electronics Express•Jan 1, 2016•8 citations

Power Reduction of Sfq Readout Circuit for Superconducting Quantum Computers

Masumi Kanda, Yuki Matsumoto, Teruo Tanimoto +2 more

The digital circuits in a superconducting quantum computer must be cooled to cryogenic temperatures in a dilution refrigerator for control and information readout of the qubit information. Because the dilution refrigerator's heat capacity is limited, extremely low-power digital circuits are required. Single-flux-quantum (SFQ) circuits and Josephson photomultipliers (JPMs) are expected to serve as control and readout circuits for superconducting quantum computers. These circuits generate minimal heat, but further reductions in power consumption are required to make it possible to build larger, more scalable faulttolerant quantum computers (FTQC). In this paper, we propose a low-power and reliable peripheral circuit for JPM-based qubit readout utilizing an SFQ counter circuit. The counter performs majority voting across repeated readouts, significantly improving the reliability of the JPM readout process. Additionally, we quantitatively evaluate switching errors in SFQ circuits using Josephson junctions with low-critical current values. By integrating these circuit techniques and simulation results, we find that the proposed approach achieves a 90% reduction in power consumption while effectively suppressing the increase in readout error.

IEEE International Conference on Quantum Computing and Engineering (QCE)•Aug 30, 2025•0 citations

Low power single flux quantum qubit control circuit without high-frequency input

Bicong Weng, Wei Peng, Jie Ren

Abstract The use of high-frequency input signals from room-temperature microwave sources makes it difficult to scale up the number of quantum bits in universal quantum computers. To address this issue, superconducting single flux quantum (SFQ) integrated circuits are being explored as suitable candidates for qubit manipulation in universal quantum computers. This paper deals with a scalable SFQ qubit control circuit (SQCC) structure that requires only low-frequency input. The circuit mainly consists of a pulse generator and a counter, that output the SFQ pulse train with adjustable frequency and a controllable number of pulses, which is applicable to control single-qubit Clifford operations. The design of low-voltage rapid single flux quantum (LV-RSFQ) and energy-efficient rapid single flux quantum (ERSFQ) for the SQCC achieves low power consumption and provides a basis for scaling up SQCC to control more qubits. The proposed circuits are fabricated under the SIMIT-Nb03 process and successfully pass test verification. The achieved test results reveal that the adjustable output frequency ranges of the SQCC based on the LV-RSFQ and ERSFQ designs in order are [2.40, 8.11] GHz and [4.81, 5.14] GHz. In the operating frequency range, the circuit is able to generate the correct number of SFQ pulses under control. The controllable number range is from 1 to 128. When the circuits operate at 5 GHz, the total power consumptions of the above circuits in order are 23.88 μW and 6.2 μW. All input signals are low-frequency signals, which frees the control of large-scale qubits from limitations caused by high-frequency inputs produced by room-temperature microwave sources.

Superconductor Science and Technology•Jul 11, 2023•6 citations

Investigation of Timing Parameters in Single-Flux-Quantum Circuits Using Low Critical-Current Junctions and Low Bias Voltages

Manami Kuniyoshi, Ken Murase, Ikki Nagaoka +4 more

In this study, the trade-off among power consumptions, operating frequencies, and error rates in low-power single-flux-quantum (SFQ) circuit is investigated. The power consumption of SFQ circuits can be reduced by the lowering critical currents ($I_{\mathrm{c}}$values) of the Josephson junctions (JJs), or the bias voltage ($V_{\mathrm{b}}$). The shifts and spreads of timing parameter fluctuations when$I_{\mathrm{c}}$and$V_{\mathrm{b}}$were lowered were numerically analyzed, with consideration of thermal noise at 4.2 K. The timing behaviors after$I_{\mathrm{c}}$was lowered were relatively simple, being based on the signal-to-noise ratio, whereas those for lowered$V_{\mathrm{b}}$values were complicated because of the dynamic behaviors of JJs driven at reduced voltage. The simulation results imply that the operating frequencies decreased because the timing windows narrowed, but the highest energy efficiency was obtained when we lowered$I_{\mathrm{c}}$or$V_{\mathrm{b}}$to 6.25% of their conventional values, and the energy reduction after lowering of$V_{\mathrm{b}}$was 26% better than that after lowering of$I_{\mathrm{c}}$. Moreover, if a small error rate (for example$10^{-6}$) is acceptable, further improvement in energy efficiency would be expected at significantly higher clock frequencies than would be the case if the SFQ circuit must exhibit error-free operation.

IEEE Transactions on Applied Superconductivity•Mar 22, 2021•9 citations

Analysis of computational energy efficiency in single-flux-quantum electronics by implementing an integer-based hardware-algorithm

Qiuyun Xu, Y. Shimamura, Yuki Yamanashi +2 more

We designed and implemented a single-flux-quantum (SFQ) based hardware-algorithm known as the 3n+1 conjecture. The circuit consists of a 16-bit integer register, a high-frequency clock generator and a central processor. This design can perform with a maximum clock frequency of 90 GHz with a total power consumption of about 0.85 mW based on the AIST 10 kA/cm2advanced Nb process. The power consumption was further reduced by using an LR-biasing approach.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2013•2 citations

Single Flux Quantum Circuit and Packaging Technology for Sub-Kelvin Temperature Operation

Shinichi Yorozu, Toshiyuki Miyazaki, Vasili K. Semenov +2 more

Superconducting single flux quantum (SFQ) technology is well known for digital logic operations below 4.2 K, which are compatible with the Josephson junction qubit. Operation speed and signal sensitivity of circuits in SFQ are also sufficient to control qubits. Therefore, the SFQ circuit is a candidate technology for multiple qubit control. However, the self-heating effect of the SFQ circuit is a potential barrier to development of an SFQ-supported multiple qubit system because the qubit operating temperature is lower than the conventional 4.2 K. The multi-chip approach is a possible solution because the qubit chip can be thermally isolated from the SFQ circuitry. We report on recent progress in SFQ circuit and packaging technology for operation at sub-Kelvin temperatures. As for multi-chip module technology, a test sample of the multi-chip module shows good reliability of electrical connections between chips, and each solder bump has a bandwidth wide enough for signal transmission. We have designed lower power SFQ circuits for sub-Kelvin temperatures. The critical currents of Josephson junctions were scaled down, inductances were scaled up, and bias voltage was reduced to make power consumption lower. Based on our fabrication technology, critical current densities were optimized by considering trade-off relations between fabrication availability and operation speed. We successfully confirmed its correct operations at around 0.35 K. The combination of the multi-chip module and optimized SFQ circuits is very effective way of controlling qubit.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•6 citations
A single-flux-quantum (SFQ) circuit is thought to be very suitable as a peripheral circuit for superconducting quantum bits (qubits), which can manipulate and detect the qubit state at a temperature state similar to qubits. Even though the power consumption of SFQ circuits is extremely small, it is still sufficient to heat the substrate at a temperature below 1 K. We have investigated and demonstrated low-power SFQ circuits for this application, using the LR-loading technique, which can reduce the static power consumption of the SFQ circuits. Simulation results show that the ratio of the switching speed to the time constant of the bias circuit is important for the stable operation of low-power SFQ circuits. The static power consumption of SFQ circuits can be reduced to the same order as the dynamic power consumption through optimization of the circuit parameters. We have designed and tested a low-power SFQ clock generator using the LR-loading technique and confirmed its stable operation at 4.2 K, where the power consumption is reduced by 93% compared with ordinary biased circuits.
We designed a low-power shift-register memory using single-flux-quantum (SFQ) circuits for bit-serial SFQ microprocessors. In order to reduce the static power consumption of the SFQ memories, LR-biasing SFQ circuits were employed, where the resistance network for supplying the bias current is replaced with the inductance network with small resistance. We implemented a low-power 1 k-bit SFQ shift-register memory and confirmed its 30 GHz operation for all addresses. The power consumption was reduced to 26% of the conventional resistively biased SFQ memories.
The digital circuits in a superconducting quantum computer must be cooled to cryogenic temperatures in a dilution refrigerator for control and information readout of the qubit information. Because the dilution refrigerator's heat capacity is limited, extremely low-power digital circuits are required. Single-flux-quantum (SFQ) circuits and Josephson photomultipliers (JPMs) are expected to serve as control and readout circuits for superconducting quantum computers. These circuits generate minimal heat, but further reductions in power consumption are required to make it possible to build larger, more scalable faulttolerant quantum computers (FTQC). In this paper, we propose a low-power and reliable peripheral circuit for JPM-based qubit readout utilizing an SFQ counter circuit. The counter performs majority voting across repeated readouts, significantly improving the reliability of the JPM readout process. Additionally, we quantitatively evaluate switching errors in SFQ circuits using Josephson junctions with low-critical current values. By integrating these circuit techniques and simulation results, we find that the proposed approach achieves a 90% reduction in power consumption while effectively suppressing the increase in readout error.
Abstract The use of high-frequency input signals from room-temperature microwave sources makes it difficult to scale up the number of quantum bits in universal quantum computers. To address this issue, superconducting single flux quantum (SFQ) integrated circuits are being explored as suitable candidates for qubit manipulation in universal quantum computers. This paper deals with a scalable SFQ qubit control circuit (SQCC) structure that requires only low-frequency input. The circuit mainly consists of a pulse generator and a counter, that output the SFQ pulse train with adjustable frequency and a controllable number of pulses, which is applicable to control single-qubit Clifford operations. The design of low-voltage rapid single flux quantum (LV-RSFQ) and energy-efficient rapid single flux quantum (ERSFQ) for the SQCC achieves low power consumption and provides a basis for scaling up SQCC to control more qubits. The proposed circuits are fabricated under the SIMIT-Nb03 process and successfully pass test verification. The achieved test results reveal that the adjustable output frequency ranges of the SQCC based on the LV-RSFQ and ERSFQ designs in order are [2.40, 8.11] GHz and [4.81, 5.14] GHz. In the operating frequency range, the circuit is able to generate the correct number of SFQ pulses under control. The controllable number range is from 1 to 128. When the circuits operate at 5 GHz, the total power consumptions of the above circuits in order are 23.88 μW and 6.2 μW. All input signals are low-frequency signals, which frees the control of large-scale qubits from limitations caused by high-frequency inputs produced by room-temperature microwave sources.
In this study, the trade-off among power consumptions, operating frequencies, and error rates in low-power single-flux-quantum (SFQ) circuit is investigated. The power consumption of SFQ circuits can be reduced by the lowering critical currents (IcI_{\mathrm{c}}Ic​values) of the Josephson junctions (JJs), or the bias voltage (VbV_{\mathrm{b}}Vb​). The shifts and spreads of timing parameter fluctuations whenIcI_{\mathrm{c}}Ic​andVbV_{\mathrm{b}}Vb​were lowered were numerically analyzed, with consideration of thermal noise at 4.2 K. The timing behaviors afterIcI_{\mathrm{c}}Ic​was lowered were relatively simple, being based on the signal-to-noise ratio, whereas those for loweredVbV_{\mathrm{b}}Vb​values were complicated because of the dynamic behaviors of JJs driven at reduced voltage. The simulation results imply that the operating frequencies decreased because the timing windows narrowed, but the highest energy efficiency was obtained when we loweredIcI_{\mathrm{c}}Ic​orVbV_{\mathrm{b}}Vb​to 6.25% of their conventional values, and the energy reduction after lowering ofVbV_{\mathrm{b}}Vb​was 26% better than that after lowering ofIcI_{\mathrm{c}}Ic​. Moreover, if a small error rate (for example10−610^{-6}10−6) is acceptable, further improvement in energy efficiency would be expected at significantly higher clock frequencies than would be the case if the SFQ circuit must exhibit error-free operation.
Superconducting single flux quantum (SFQ) technology is well known for digital logic operations below 4.2 K, which are compatible with the Josephson junction qubit. Operation speed and signal sensitivity of circuits in SFQ are also sufficient to control qubits. Therefore, the SFQ circuit is a candidate technology for multiple qubit control. However, the self-heating effect of the SFQ circuit is a potential barrier to development of an SFQ-supported multiple qubit system because the qubit operating temperature is lower than the conventional 4.2 K. The multi-chip approach is a possible solution because the qubit chip can be thermally isolated from the SFQ circuitry. We report on recent progress in SFQ circuit and packaging technology for operation at sub-Kelvin temperatures. As for multi-chip module technology, a test sample of the multi-chip module shows good reliability of electrical connections between chips, and each solder bump has a bandwidth wide enough for signal transmission. We have designed lower power SFQ circuits for sub-Kelvin temperatures. The critical currents of Josephson junctions were scaled down, inductances were scaled up, and bias voltage was reduced to make power consumption lower. Based on our fabrication technology, critical current densities were optimized by considering trade-off relations between fabrication availability and operation speed. We successfully confirmed its correct operations at around 0.35 K. The combination of the multi-chip module and optimized SFQ circuits is very effective way of controlling qubit.