Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Measurement of 10 zJ energy dissipation of adiabatic quantum-flux-parametron logic using a superconducting resonator

Naoki Takeuchi, Yuki Yamanashi, Nobuyuki Yoshikawa

Published Feb 4, 2013• 84 citations
Publisher

Abstract

Adiabatic quantum-flux-parametron (AQFP) logic has the potential to operate with an ultimately small bit energy of several zeptojoules; however, this is too small to measure by conventional techniques. We measure such a small energy dissipation by coupling a superconducting resonator with an AQFP gate, where the insertion loss is sensitively varied with the small dissipation due to the very high Q factor of the resonator. We designed and implemented a 5 GHz superconducting resonator coupled with an AQFP gate. Measurement results show that the bit energy of the gate is ∼10 zJ at 5 GHz operation.

DOI
10.1063/1.4790276

Related papers

Measurement of low bit-error-rates of adiabatic quantum-flux-parametron logic using a superconductor voltage driver

Naoki Takeuchi, Hideo Suzuki, Nobuyuki Yoshikawa

Adiabatic quantum-flux-parametron (AQFP) is an energy-efficient superconductor logic. The advantage of AQFP is that the switching energy can be reduced by lowering operation frequencies or by increasing the quality factors of Josephson junctions, while keeping the energy barrier height much larger than thermal energy. In other words, both low energy dissipation and low bit error rates (BERs) can be achieved. In this paper, we report the first measurement results of the low BERs of AQFP logic. We used a superconductor voltage driver with a stack of dc superconducting-quantum-interference-devices to amplify the logic signals of AQFP gates into mV-range voltage signals for the BER measurement. Our measurement results showed 3.3 dB and 2.6 dB operation margins, in which BERs were less than 10−20, for 1 Gbps and 2 Gbps data rates, respectively. While the observed BERs were very low, the estimated switching energy for the 1-Gbps operation was only 2 zJ or 30kBT, where kB is the Boltzmann's constant and T is the temperature. Unlike conventional non-adiabatic logic, BERs are not directly associated with switching energy in AQFP.

Applied Physics Letters•May 15, 2017•28 citations

Simulation and Experimental Demonstration of Logic Circuits Using an Ultra-Low-Power Adiabatic Quantum-Flux-Parametron

Koji Inoue, Naoki Takeuchi, Kei Ehara +2 more

We have been investigating an ultra-low-power adiabatic quantum-flux-parametron (AQFP) logic, the energy dissipation of which can be decreased by changing its potential energy slowly or adiabatically. In the present study, we designed basic AQFP logic gates and an AQFP 1-bit full adder, and examined their operations through simulations and experiments. The AQFP 1-bit full adder is composed of 46 Josephson junctions, which is approximately one-quarter the number of junctions of a full adder using conventional rapid single-flux-quantum logic. The measurement results indicated that the AQFP 1-bit full adder has a wide current bias margin of as large as ±27.8%.

IEEE Transactions on Applied Superconductivity•Dec 24, 2012•39 citations

An adiabatic superconductor 8-bit adder with 24kBT energy dissipation per junction

Naoki Takeuchi, Taiki Yamae, Christopher Lawrence Ayala +2 more

Adiabatic quantum-flux-parametron (AQFP) logic is an energy-efficient superconductor logic family. In this paper, we conducted the high-frequency operation and energy measurement of an AQFP circuit with more than 1000 Josephson junctions in the experiment. We designed an 8-bit carry look-ahead adder (CLA) using AQFP gates and fabricated it using an advanced fabrication technology, the AIST 10 kA/cm2 Nb high-speed standard process. The correct operation of the 8-bit CLA was demonstrated at a 1-GHz clock frequency for a critical carry propagation test vector. The energy dissipation of the 8-bit CLA was measured by observing the power of excitation current. Our results showed that the energy dissipation per operation of the 8-bit CLA can be estimated to be approximately 1.5 aJ, or 24kBT per junction, where kB is the Boltzmann constant and T is the operating temperature.

Applied Physics Letters•Jan 28, 2019•67 citations

Extremely Energy-Efficient Integrated Circuits Using Adiabatic Superconductor Logic

尚輝 竹内

Complementary metal-oxide-semiconductor (CMOS) circuit technology has sustainedthe exponential growth of computing power for more than 20 years. However, it hasbeen estimated that the power consumption of a next-generation supercomputer willexceed the power supplied from a single power plant. This indicates the need to dramaticallyimprove the energy efficiency of logic devices to achieve future high-endcomputers.As an extremely energy-efficient logic, we proposed and have been investigatingadiabatic quantum-flux-parametron (AQFP) devices. Due to adiabatic switching operations,its bit energy (energy dissipation per bit) can go below Ic 0, where Ic is acritical current of a Josephson junction and 0 is a single-flux-quantum (SFQ). Ic 0corresponds to the energy dissipated at every 2 phase transition in conventional nonadiabaticsuperconductor logics.We have two objectives in this study. One is to reveal physical energy bounds oncomputation through investigation of the energy efficiency of AQFP logic. The otheris to develop fundamental circuits necessary for energy-efficient computing systemsusing AQFP logic.First, we numerically and experimentally demonstrated the sub-Ic 0 bit-energyoperations of AQFP gates to show that AQFP gates operate in adiabatic modes. Weinvestigated the dependence of energy dissipation and operation margins on circuitparameters. After optimizing the parameters, we calculated the bit energy and the biterror rate at 4.2 K to verify the sub-Ic 0 bit-energy operations at a finite temperature.Additionally, we measured the bit energy of an AQFP gate using a superconductorresonator-based method.Secondly, we numerically demonstrated the sub-kBT bit-energy operations, wherekB is the Boltzmann constant and T is temperature, to show that AQFP gates can operatebeyond thermodynamic energy bounds. We investigated the dependence of energydissipation on operation frequencies and damping conditions of Josephson junctions.By using underdamped junctions, we confirmed the sub-kBT bit-energy operationsat a finite temperature thorough circuit simulation. This result indicates that thereis no minimum energy dissipation required for the operations of AQFP gates unlessthe entropy of the system decreases, which corresponds to the Landauer’s argument on the minimum energy dissipation for computation. Also, we discussed quantummechanicalenergy bounds and experimentally demonstrated AQFP gates with underdampedjunctions.Additionally, we investigated reversible computing using AQFP logic with underdampedjunctions, in order to deal with an important but unresolved question: “Isreversible computing achievable by using practical devices?” We built a purely reversiblegate by using AQFP gates, which we designated as the reversible quantumflux-parametron (RQFP) gate. We calculated its energy dissipation and confirmed thatthere is no minimum energy dissipation for reversible logic operations using RQFPgates. To the best of our knowledge, these are the first calculation results that show nominimum energy dissipation in reversible computing that use practical circuit structures.Moreover, our experimental results have demonstrated the logical and physicalreversibility of the RQFP gate. We believe that this is the first demonstration thatshows both logical and physical reversibility using practical devices.Finally, we proposed a novel energy-efficient latch for AQFP logic, which we designatedas the quantum-flux-latch (QFL). Latches are necessary circuitries in largecomputing systems but had been missing in AQFP logic. We discussed its energyefficiency through simulation and experimentally demonstrated correct operations ofthe QFL and a 1-bit shift register using QFLs. Also, we proposed high-speed test circuitsusing QFLs and experimentally demonstrated logic operations of AQFP circuitsat high speed.We strongly believe that our results showed the extremely high energy efficiency ofAQFP logic. These results will move the AQFP logic to practical usage as extremelyenergy-efficient integrated circuits.

•Mar 26, 2014•1 citation

Operation of an Adiabatic Quantum-Flux-Parametron Gate Using an On-Chip AC Power Source

Takashi Mukaiyama, Naoki Takeuchi, Kohei Ehara +3 more

Adiabatic quantum-flux-parametron (AQFP) logic devices can operate under extremely low bit energy approaching the thermal limit by varying their potential energy adiabatically using ac bias currents. We have proposed an on-chip ac power source, which is composed of a Josephson relaxation oscillator and a superconductingLCresonator in order to drive AQFP circuits at 5 GHz or higher frequencies. We herein experimentally confirmed the correct switching operation of an AQFP gate at 4.94 GHz using the proposed on-chip ac power source. Furthermore, we confirmed that the ac power source can drive approximately 800 AQFP gates.

IEEE Transactions on Applied Superconductivity•Apr 8, 2013•7 citations

Simulation of sub-kBT bit-energy operation of adiabatic quantum-flux-parametron logic with low bit-error-rate

Naoki Takeuchi, Yuki Yamanashi, Nobuyuki Yoshikawa

Adiabatic quantum-flux-parametron (AQFP) logic can achieve high energy-efficiency. The bit energy and bit-error-rate (BER) of AQFP gates with under-damped Josephson junctions were simulated. The results indicate that the bit energy reaches 12 yJ, which is only 20% of the thermal energy at 4.2 K, using unshunted 50-μA junctions and excitation currents with a rise/fall time of 2000 ps. Although the bit energy is extremely small, the bias margin, where the BER is less than 10−23, is approximately ±22%. These results indicate there is no minimum energy limitation for the operation of AQFP gates unless the entropy of the system decreases.

Applied Physics Letters•Aug 5, 2013•48 citations
Adiabatic quantum-flux-parametron (AQFP) logic has the potential to operate with an ultimately small bit energy of several zeptojoules; however, this is too small to measure by conventional techniques. We measure such a small energy dissipation by coupling a superconducting resonator with an AQFP gate, where the insertion loss is sensitively varied with the small dissipation due to the very high Q factor of the resonator. We designed and implemented a 5 GHz superconducting resonator coupled with an AQFP gate. Measurement results show that the bit energy of the gate is ∼10 zJ at 5 GHz operation.
Adiabatic quantum-flux-parametron (AQFP) is an energy-efficient superconductor logic. The advantage of AQFP is that the switching energy can be reduced by lowering operation frequencies or by increasing the quality factors of Josephson junctions, while keeping the energy barrier height much larger than thermal energy. In other words, both low energy dissipation and low bit error rates (BERs) can be achieved. In this paper, we report the first measurement results of the low BERs of AQFP logic. We used a superconductor voltage driver with a stack of dc superconducting-quantum-interference-devices to amplify the logic signals of AQFP gates into mV-range voltage signals for the BER measurement. Our measurement results showed 3.3 dB and 2.6 dB operation margins, in which BERs were less than 10−20, for 1 Gbps and 2 Gbps data rates, respectively. While the observed BERs were very low, the estimated switching energy for the 1-Gbps operation was only 2 zJ or 30kBT, where kB is the Boltzmann's constant and T is the temperature. Unlike conventional non-adiabatic logic, BERs are not directly associated with switching energy in AQFP.
We have been investigating an ultra-low-power adiabatic quantum-flux-parametron (AQFP) logic, the energy dissipation of which can be decreased by changing its potential energy slowly or adiabatically. In the present study, we designed basic AQFP logic gates and an AQFP 1-bit full adder, and examined their operations through simulations and experiments. The AQFP 1-bit full adder is composed of 46 Josephson junctions, which is approximately one-quarter the number of junctions of a full adder using conventional rapid single-flux-quantum logic. The measurement results indicated that the AQFP 1-bit full adder has a wide current bias margin of as large as ±27.8%.
Adiabatic quantum-flux-parametron (AQFP) logic is an energy-efficient superconductor logic family. In this paper, we conducted the high-frequency operation and energy measurement of an AQFP circuit with more than 1000 Josephson junctions in the experiment. We designed an 8-bit carry look-ahead adder (CLA) using AQFP gates and fabricated it using an advanced fabrication technology, the AIST 10 kA/cm2 Nb high-speed standard process. The correct operation of the 8-bit CLA was demonstrated at a 1-GHz clock frequency for a critical carry propagation test vector. The energy dissipation of the 8-bit CLA was measured by observing the power of excitation current. Our results showed that the energy dissipation per operation of the 8-bit CLA can be estimated to be approximately 1.5 aJ, or 24kBT per junction, where kB is the Boltzmann constant and T is the operating temperature.
Complementary metal-oxide-semiconductor (CMOS) circuit technology has sustainedthe exponential growth of computing power for more than 20 years. However, it hasbeen estimated that the power consumption of a next-generation supercomputer willexceed the power supplied from a single power plant. This indicates the need to dramaticallyimprove the energy efficiency of logic devices to achieve future high-endcomputers.As an extremely energy-efficient logic, we proposed and have been investigatingadiabatic quantum-flux-parametron (AQFP) devices. Due to adiabatic switching operations,its bit energy (energy dissipation per bit) can go below Ic 0, where Ic is acritical current of a Josephson junction and 0 is a single-flux-quantum (SFQ). Ic 0corresponds to the energy dissipated at every 2 phase transition in conventional nonadiabaticsuperconductor logics.We have two objectives in this study. One is to reveal physical energy bounds oncomputation through investigation of the energy efficiency of AQFP logic. The otheris to develop fundamental circuits necessary for energy-efficient computing systemsusing AQFP logic.First, we numerically and experimentally demonstrated the sub-Ic 0 bit-energyoperations of AQFP gates to show that AQFP gates operate in adiabatic modes. Weinvestigated the dependence of energy dissipation and operation margins on circuitparameters. After optimizing the parameters, we calculated the bit energy and the biterror rate at 4.2 K to verify the sub-Ic 0 bit-energy operations at a finite temperature.Additionally, we measured the bit energy of an AQFP gate using a superconductorresonator-based method.Secondly, we numerically demonstrated the sub-kBT bit-energy operations, wherekB is the Boltzmann constant and T is temperature, to show that AQFP gates can operatebeyond thermodynamic energy bounds. We investigated the dependence of energydissipation on operation frequencies and damping conditions of Josephson junctions.By using underdamped junctions, we confirmed the sub-kBT bit-energy operationsat a finite temperature thorough circuit simulation. This result indicates that thereis no minimum energy dissipation required for the operations of AQFP gates unlessthe entropy of the system decreases, which corresponds to the Landauer’s argument on the minimum energy dissipation for computation. Also, we discussed quantummechanicalenergy bounds and experimentally demonstrated AQFP gates with underdampedjunctions.Additionally, we investigated reversible computing using AQFP logic with underdampedjunctions, in order to deal with an important but unresolved question: “Isreversible computing achievable by using practical devices?” We built a purely reversiblegate by using AQFP gates, which we designated as the reversible quantumflux-parametron (RQFP) gate. We calculated its energy dissipation and confirmed thatthere is no minimum energy dissipation for reversible logic operations using RQFPgates. To the best of our knowledge, these are the first calculation results that show nominimum energy dissipation in reversible computing that use practical circuit structures.Moreover, our experimental results have demonstrated the logical and physicalreversibility of the RQFP gate. We believe that this is the first demonstration thatshows both logical and physical reversibility using practical devices.Finally, we proposed a novel energy-efficient latch for AQFP logic, which we designatedas the quantum-flux-latch (QFL). Latches are necessary circuitries in largecomputing systems but had been missing in AQFP logic. We discussed its energyefficiency through simulation and experimentally demonstrated correct operations ofthe QFL and a 1-bit shift register using QFLs. Also, we proposed high-speed test circuitsusing QFLs and experimentally demonstrated logic operations of AQFP circuitsat high speed.We strongly believe that our results showed the extremely high energy efficiency ofAQFP logic. These results will move the AQFP logic to practical usage as extremelyenergy-efficient integrated circuits.
Adiabatic quantum-flux-parametron (AQFP) logic devices can operate under extremely low bit energy approaching the thermal limit by varying their potential energy adiabatically using ac bias currents. We have proposed an on-chip ac power source, which is composed of a Josephson relaxation oscillator and a superconductingLCresonator in order to drive AQFP circuits at 5 GHz or higher frequencies. We herein experimentally confirmed the correct switching operation of an AQFP gate at 4.94 GHz using the proposed on-chip ac power source. Furthermore, we confirmed that the ac power source can drive approximately 800 AQFP gates.
Adiabatic quantum-flux-parametron (AQFP) logic can achieve high energy-efficiency. The bit energy and bit-error-rate (BER) of AQFP gates with under-damped Josephson junctions were simulated. The results indicate that the bit energy reaches 12 yJ, which is only 20% of the thermal energy at 4.2 K, using unshunted 50-μA junctions and excitation currents with a rise/fall time of 2000 ps. Although the bit energy is extremely small, the bias margin, where the BER is less than 10−23, is approximately ±22%. These results indicate there is no minimum energy limitation for the operation of AQFP gates unless the entropy of the system decreases.