Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Tracing the characteristics of a flux qubit with a hysteretic dc-superconducting quantum interference device comparator

Maria Gabriella Castellano, F. Chiarello, Roberto Leoni, Daniela Simeone, G. Torrioli, C. Cosmelli, R. Buttiglione, Stefano Poletto, P. Carelli

Published Dec 4, 2003• 4 citations
Publisher

Abstract

A hysteretic dc-superconducting quantum interference device (SQUID) is used to trace the flux characteristic of a tunable rf-SQUID, the basic element for the realization of superconducting flux qubits. This allows important simplifications of circuitry and electronics in developing devices for quantum computing, by eliminating the necessity of more complex magnetometers. A hysteretic dc-SQUID is usually operated as a comparator, distinguishing only which one of two adjacent flux states is occupied by the rf-SQUID. The necessary sensitivity, moreover, is usually reached only at temperatures in the mK range. However, by exploiting the statistical properties of the current–voltage curve in the region where the switching from the zero-voltage state occurs, it is possible to obtain an accurate tracing of the input flux, even at a relatively high temperature (a few Kelvin). In our case, the input signal is given by the internal flux of a tunable rf-SQUID, the building block of a flux qubit.

DOI
10.1063/1.1628382

Related papers

A hysteretic dc SQUID reading the flux states of an rf SQUID

C. Cosmelli, P. Carelli, Maria Gabriella Castellano +3 more

We have realized a hysteretic dc SQUID to measure the flux states of a rf SQUID inductively coupled to the hysteretic dc SQUID. This type of measurement is required whenever is necessary to make a non invasive measure of the state of the rf SQUID. This is the case of measurements of macroscopic quantum coherence or measurements on q-bits systems. With the proposed set up the hysteretic dc SQUID can switch from the superconducting to the normal state depending on the total applied magnetic flux. On this system we measured at 4.2 K the change on the switching probability of the dc SQUID by varying the flux state of the rf SQUID. The experimental results agree very well with the theoretical predictions showing that this device can be used to perform non invasive measurements of the rf SQUID flux state.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•12 citations

Tuning an rf-SQUID flux qubit system's potential with magnetic flux bias

Tao Hua, Weiwei Xu, Jianxin Shi +4 more

At an extremely low temperature of 20 mK, we measured the loop current in a tunable rf superconducting quantum interference device (SQUID) with a dc-SQUID. By adjusting the magnetic flux applied to the rf-SQUID loop ( Φ f ) and the small dc-SQUID ( Φ f cjj ), respectively, the potential shape of the system can be fully controlled in situ . Variation in the transition step and overlap size in the switching current with a barrier flux bias are analyzed, from which we can obtain some relevant device parameters and build a model to explain the experimental phenomenon.

Chinese Physics B•Sep 1, 2012•4 citations

Efficiency of underdamped dc SQUIDs as readout devices for flux qubits

Shaoxiong Li, Yang Yu, Wei Qiu +2 more

The flux state quantum bit (qubit) is promising for a solid state implementation of scalable quantum computing. The simplest flux state qubit consists of an rf SQUID with two fluxoid states, which can be readout with a dc SQUID - the most sensitive magnetic flux detector. Efficient readout with less back-action is desirable for quantum computing. In this work, we report measurements of the switching flux and switching current distributions of under damped dc SQUIDs. The data show that single shot readout of flux qubit with very high efficiency (>99%) can be realized using underdamped hysteretic dc SQUIDs.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•2 citations

Stroboscopic single-shot detection of the flux state in a radio frequency superconducting quantum interference device

C. Cosmelli, F. Sciamanna, Maria Gabriella Castellano +4 more

The flux states of a rf superconducting quantum interference device (SQUID) can be used to investigate macroscopic quantum effects, the most challenging of which is the detection of quantum coherent oscillations, and are promising candidates for the implementation of quantum computing. The use of a proper readout system is of utmost importance for these purposes. In this letter we present experimental evidence of the possibility of using an underdamped, hysteretic dc SQUID to read out stroboscopically the flux states of a rf SQUID, allowing a single shot discrimination with an efficiency of 98%. The devices are all integrated on chip.

Applied Physics Letters•Apr 29, 2002•14 citations

dc SQUID's I–V Characteristics and Its Bias Modes

Yi Zhang, Hui Dong, Hans-Joachim Krause +2 more

The physics of a DC Superconducting QUantum Interference Device (SQUID) involves two phenomena: flux quantization and Josephson tunneling. This chapter describes how to measure and understand a SQUID's I–V characteristics. It also describes how to realize an ideal current source for biasing a SQUID and how to set up a practical voltage source to operate a SQUID in voltage bias mode. To study a DC SQUID's features, the first step is to obtain its I–V characteristics. In contrast to the I–V characteristics of the resistor or the diode, those of the SQUID are modulated by the applied flux but are limited within two flux states of integer and half-integer. An ideal current source is characterized by an internal resistance approaching infinity, compared to the SQUID's dynamic resistance. There are only two realized concepts for the SQUID operation in voltage bias mode.

Wiley eBooks•May 29, 2020•0 citations

Low-Back-Action RF SQUID Readout for a Josephson Flux Qubit Measurement

V. I. Shnyrkov, Andrii P. Shapovalov, A.A. Kalenyuk +3 more

Superconducting qubits demonstrate good perspectives as scalable blocks for quantum information processing. These systems can be individually readout, addressed, and controlled, making them some of the most attractive thin-film qubits. Quantum measurements should be performed in order to readout the final state of flux qubits. To observe the dynamics of such systems, one requires a fast magnetometer with exceptional sensitivity and low back-action. We address the problem of reducing the back-action of an RF SQUID readout circuit, which may significantly destroy a Josephson flux qubit in the case of the circuits integration. The main sources of such back-action in conventional RF SQUID and DC SQUID circuits are low-ohmic shunting resistors ensuring high damping. The advantage of flux qubits is the presence of an optimal bias point at which, in the first-order approximation, the device is immune to fluctuations in readout and control lines. Nonetheless, even such systems have characteristics limited by a second-order dissipation. The dissipation can be eliminated by using an “ideal parametric readout” based on an RF SQUID acting in non-hysteretic adiabatic mode. In this paper, we propose an RF SQUID in a non-hysteretic regime as a fast, sensitive, and scalable readout system with low back-action for measurements of a single MW photon counter based on a flux qubit.

IEEE International Conference on Electronics and Information Technologies (ELIT)•May 19, 2021•1 citation
A hysteretic dc-superconducting quantum interference device (SQUID) is used to trace the flux characteristic of a tunable rf-SQUID, the basic element for the realization of superconducting flux qubits. This allows important simplifications of circuitry and electronics in developing devices for quantum computing, by eliminating the necessity of more complex magnetometers. A hysteretic dc-SQUID is usually operated as a comparator, distinguishing only which one of two adjacent flux states is occupied by the rf-SQUID. The necessary sensitivity, moreover, is usually reached only at temperatures in the mK range. However, by exploiting the statistical properties of the current–voltage curve in the region where the switching from the zero-voltage state occurs, it is possible to obtain an accurate tracing of the input flux, even at a relatively high temperature (a few Kelvin). In our case, the input signal is given by the internal flux of a tunable rf-SQUID, the building block of a flux qubit.
We have realized a hysteretic dc SQUID to measure the flux states of a rf SQUID inductively coupled to the hysteretic dc SQUID. This type of measurement is required whenever is necessary to make a non invasive measure of the state of the rf SQUID. This is the case of measurements of macroscopic quantum coherence or measurements on q-bits systems. With the proposed set up the hysteretic dc SQUID can switch from the superconducting to the normal state depending on the total applied magnetic flux. On this system we measured at 4.2 K the change on the switching probability of the dc SQUID by varying the flux state of the rf SQUID. The experimental results agree very well with the theoretical predictions showing that this device can be used to perform non invasive measurements of the rf SQUID flux state.
At an extremely low temperature of 20 mK, we measured the loop current in a tunable rf superconducting quantum interference device (SQUID) with a dc-SQUID. By adjusting the magnetic flux applied to the rf-SQUID loop ( Φ f ) and the small dc-SQUID ( Φ f cjj ), respectively, the potential shape of the system can be fully controlled in situ . Variation in the transition step and overlap size in the switching current with a barrier flux bias are analyzed, from which we can obtain some relevant device parameters and build a model to explain the experimental phenomenon.
The flux state quantum bit (qubit) is promising for a solid state implementation of scalable quantum computing. The simplest flux state qubit consists of an rf SQUID with two fluxoid states, which can be readout with a dc SQUID - the most sensitive magnetic flux detector. Efficient readout with less back-action is desirable for quantum computing. In this work, we report measurements of the switching flux and switching current distributions of under damped dc SQUIDs. The data show that single shot readout of flux qubit with very high efficiency (>99%) can be realized using underdamped hysteretic dc SQUIDs.
The flux states of a rf superconducting quantum interference device (SQUID) can be used to investigate macroscopic quantum effects, the most challenging of which is the detection of quantum coherent oscillations, and are promising candidates for the implementation of quantum computing. The use of a proper readout system is of utmost importance for these purposes. In this letter we present experimental evidence of the possibility of using an underdamped, hysteretic dc SQUID to read out stroboscopically the flux states of a rf SQUID, allowing a single shot discrimination with an efficiency of 98%. The devices are all integrated on chip.
The physics of a DC Superconducting QUantum Interference Device (SQUID) involves two phenomena: flux quantization and Josephson tunneling. This chapter describes how to measure and understand a SQUID's I–V characteristics. It also describes how to realize an ideal current source for biasing a SQUID and how to set up a practical voltage source to operate a SQUID in voltage bias mode. To study a DC SQUID's features, the first step is to obtain its I–V characteristics. In contrast to the I–V characteristics of the resistor or the diode, those of the SQUID are modulated by the applied flux but are limited within two flux states of integer and half-integer. An ideal current source is characterized by an internal resistance approaching infinity, compared to the SQUID's dynamic resistance. There are only two realized concepts for the SQUID operation in voltage bias mode.
Superconducting qubits demonstrate good perspectives as scalable blocks for quantum information processing. These systems can be individually readout, addressed, and controlled, making them some of the most attractive thin-film qubits. Quantum measurements should be performed in order to readout the final state of flux qubits. To observe the dynamics of such systems, one requires a fast magnetometer with exceptional sensitivity and low back-action. We address the problem of reducing the back-action of an RF SQUID readout circuit, which may significantly destroy a Josephson flux qubit in the case of the circuits integration. The main sources of such back-action in conventional RF SQUID and DC SQUID circuits are low-ohmic shunting resistors ensuring high damping. The advantage of flux qubits is the presence of an optimal bias point at which, in the first-order approximation, the device is immune to fluctuations in readout and control lines. Nonetheless, even such systems have characteristics limited by a second-order dissipation. The dissipation can be eliminated by using an “ideal parametric readout” based on an RF SQUID acting in non-hysteretic adiabatic mode. In this paper, we propose an RF SQUID in a non-hysteretic regime as a fast, sensitive, and scalable readout system with low back-action for measurements of a single MW photon counter based on a flux qubit.