Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Circuits and Systems I Regular Papers

Sub-Nanoampere One-Shot Single Electron Transistor Readout Electrometry Below 10 Kelvin

Kushal Das, Torsten Lehmann, Andrew S. Dzurak

Published Sep 18, 2014• 18 citations
Publisher

Abstract

The Single Electron Transistor holds the potential to be a suitable readout device for future solid-state quantum computers. The low temperature measurement results of a 0.5 μm Silicon-On-Sapphire CMOS circuit designed to interface with a Single Electron Transistor are presented. Careful design of the experimental set-up is critical for conducting the circuit test and performance measurements at cryogenic temperatures. The circuit operates at 4 K and achieves single-shot readout with a resolution in the order of one nanoampere. A detection delay as low as 1.5 μs is recorded while dissipating only 20-30 μW power.

DOI
10.1109/tcsi.2014.2321196

Related papers

CMOS Integrated Single Electron Transistor Electrometry (CMOS-SET) Circuit Design for Nanosecond Quantum-Bit Read-out

Thomas M. Gurrieri, Malcolm S. Carroll, Michael P Lilly +1 more

Novel single electron transistor (SET) read-out circuit designs are described. The circuits use a silicon SET interfaced to a CMOS voltage mode or current mode comparator to obtain a digital read-out of the state of the qubit. The design assumes standard submicron (0.35 um) CMOS SOI technology using room temperature SPICE models. Implications and uncertainties related to the temperature scaling of these models to 100mK operation are discussed. Using this technology, the simulations predict a read-out operation speed of approximately Ins and a power dissipation per cell as low as 2nW for single-shot read-out, which is a significant advantage over currently used radio frequency SET (RF-SET) approaches.

IEEE Conference on Nanotechnology (IEEE NANO)•Aug 1, 2008•14 citations

Single shot spin readout using a cryogenic high-electron-mobility transistor amplifier at sub-Kelvin temperatures

Lisa A Tracy, Dwight Luhman, Stephen M Carr +6 more

We use a cryogenic high-electron-mobility transistor circuit to amplify the current from a single electron transistor, allowing for demonstration of single shot readout of an electron spin on a single P donor in Si with 100 kHz bandwidth and a signal to noise ratio of ∼9. In order to reduce the impact of cable capacitance, the amplifier is located adjacent to the Si sample, at the mixing chamber stage of a dilution refrigerator. For a current gain of ∼2.7×103, the power dissipation of the amplifier is 13 μW, the bandwidth is ∼1.3 MHz, and for frequencies above 300 kHz the current noise referred to input is ≤70 fA/Hz. With this amplification scheme, we are able to observe coherent oscillations of a P donor electron spin in isotopically enriched 28Si with 96% visibility.

Applied Physics Letters•Feb 8, 2016•60 citations

Single shot measurement in silicon single electron transistors

T. Ferrus, D. A. Williams, D. G. Hasko +7 more

A major problem of usual current measurement setup is the severe limitations on the bandwidth due to room temperature electronics. This restricts the practical measurement rate to below 10 Hz and makes impossible to observe the evolution of a quantum state in real time. Here we describe a measurement on a silicon single electron transistor (SET) carried out using a custom CMOS measurement circuit in close proximity to the device under test. Both the device and the CMOS circuit are maintained in the same cryogenic environment. Quantum mechanical states in the single electron transistor (SET) were mapped by continuous microwave spectroscopy. The real time evolution of a particularly long lived quantum mechanical state was observed in a single shot measurement, made possible by the much faster measurement rate. This technique will shortly be applied to the measurement of coherent states in a charge qubit device made of a silicon double dot.

IEEE Silicon Nanoelectronics Workshop•Jun 1, 2008•0 citations

Single shot measurement of a silicon single electron transistor

D. G. Hasko, T. Ferrus, Q. Morrissey +8 more

We have fabricated a custom cryogenic complementary metal-oxide-semiconductor integrated circuit that has a higher measurement bandwidth compared to conventional room temperature electronics. This allowed implementing single shot operations and observe the real-time evolution of the current of a phosphorus-doped silicon single electron transistor that was irradiated with a microwave pulse. Relaxation times up to 90μs are observed, suggesting the presence of well isolated electron excitations within the device. It is expected that these are associated with long decoherence time and the device may be suitable for quantum information processing.

arXiv:0811.0736•Applied Physics Letters•Nov 10, 2008•10 citations

Single-Shot Readout Performance of Two Heterojunction-Bipolar-Transistor Amplification Circuits at Millikelvin Temperatures

Matthew Curry, M. Rudolph, Troy D. England +12 more

Abstract High-fidelity single-shot readout of spin qubits requires distinguishing states much faster than the T 1 time of the spin state. One approach to improving readout fidelity and bandwidth (BW) is cryogenic amplification, where the signal from the qubit is amplified before noise sources are introduced and room-temperature amplifiers can operate at lower gain and higher BW. We compare the performance of two cryogenic amplification circuits: a current-biased heterojunction bipolar transistor circuit (CB-HBT), and an AC-coupled HBT circuit (AC-HBT). Both circuits are mounted on the mixing-chamber stage of a dilution refrigerator and are connected to silicon metal oxide semiconductor (Si-MOS) quantum dot devices on a printed circuit board (PCB). The power dissipated by the CB-HBT ranges from 0.1 to 1 μ W whereas the power of the AC-HBT ranges from 1 to 20 μ W. Referred to the input, the noise spectral density is low for both circuits, in the 15 to 30 fA/ $$\sqrt{{\bf{Hz}}}$$ Hz range. The charge sensitivity for the CB-HBT and AC-HBT is 330 μ e/ $$\sqrt{{\bf{Hz}}}$$ Hz and 400 μ e/ $$\sqrt{{\bf{Hz}}}$$ Hz , respectively. For the single-shot readout performed, less than 10 μ s is required for both circuits to achieve bit error rates below 10 −3 , which is a putative threshold for quantum error correction.

arXiv:1901.04570•Scientific Reports•Nov 18, 2019•31 citations

Quantum bit controller and observer circuits in SOS-CMOS technology for gigahertz low-temperature operation

Sithumini Ekanayake, Torsten Lehmann, Andrew S. Dzurak +1 more

Quantum bit (qubit) control and readout requires controller-qubit-observer systems for rapid control signal generation and injection to the qubit gates, and observation of their final state projections. Conventionally, for solid-state qubits, this is achieved by generating the control signal at 300 K and transmitting it along very long coaxial cables that span from 300 K to sub-K (typically les 500 mK), then reading out the response from charge proximity sensors such as single-electron transistors along similar lengths of cable. Our approach is to fabricate the classical controller and observer circuits using a commercial foundry processed silicon-on-sapphire (SOS) RFCMOS technology for operation at low temperatures (either at 4.2 K, 1 K, or sub-K). We have demonstrated SOS-CMOS NFET and PFET device operation at 4.2 K, and sub-K that showed deviations from their 300 K characteristics, but with further experiments these were shown to have minimal effects on control circuit function. Using these results, we have fabricated and demonstrated a low-power proof-of-concept SOS-CMOS controller circuit (monostable 100 ps voltage-pulse generator) that can operate at sub-K temperatures in a dilution refrigerator. We briefly discuss experimental and conceptual schemes with which we can develop qubit control systems for cryogenic and lower temperatures. These low temperature experiments also demonstrate that commercial SOS RF-CMOS technology can be feasible for other low temperature and low power applications.

IEEE Conference on Nanotechnology (IEEE NANO)•Aug 1, 2007•9 citations
The Single Electron Transistor holds the potential to be a suitable readout device for future solid-state quantum computers. The low temperature measurement results of a 0.5 μm Silicon-On-Sapphire CMOS circuit designed to interface with a Single Electron Transistor are presented. Careful design of the experimental set-up is critical for conducting the circuit test and performance measurements at cryogenic temperatures. The circuit operates at 4 K and achieves single-shot readout with a resolution in the order of one nanoampere. A detection delay as low as 1.5 μs is recorded while dissipating only 20-30 μW power.
Novel single electron transistor (SET) read-out circuit designs are described. The circuits use a silicon SET interfaced to a CMOS voltage mode or current mode comparator to obtain a digital read-out of the state of the qubit. The design assumes standard submicron (0.35 um) CMOS SOI technology using room temperature SPICE models. Implications and uncertainties related to the temperature scaling of these models to 100mK operation are discussed. Using this technology, the simulations predict a read-out operation speed of approximately Ins and a power dissipation per cell as low as 2nW for single-shot read-out, which is a significant advantage over currently used radio frequency SET (RF-SET) approaches.
We use a cryogenic high-electron-mobility transistor circuit to amplify the current from a single electron transistor, allowing for demonstration of single shot readout of an electron spin on a single P donor in Si with 100 kHz bandwidth and a signal to noise ratio of ∼9. In order to reduce the impact of cable capacitance, the amplifier is located adjacent to the Si sample, at the mixing chamber stage of a dilution refrigerator. For a current gain of ∼2.7×103, the power dissipation of the amplifier is 13 μW, the bandwidth is ∼1.3 MHz, and for frequencies above 300 kHz the current noise referred to input is ≤70 fA/Hz. With this amplification scheme, we are able to observe coherent oscillations of a P donor electron spin in isotopically enriched 28Si with 96% visibility.
A major problem of usual current measurement setup is the severe limitations on the bandwidth due to room temperature electronics. This restricts the practical measurement rate to below 10 Hz and makes impossible to observe the evolution of a quantum state in real time. Here we describe a measurement on a silicon single electron transistor (SET) carried out using a custom CMOS measurement circuit in close proximity to the device under test. Both the device and the CMOS circuit are maintained in the same cryogenic environment. Quantum mechanical states in the single electron transistor (SET) were mapped by continuous microwave spectroscopy. The real time evolution of a particularly long lived quantum mechanical state was observed in a single shot measurement, made possible by the much faster measurement rate. This technique will shortly be applied to the measurement of coherent states in a charge qubit device made of a silicon double dot.
We have fabricated a custom cryogenic complementary metal-oxide-semiconductor integrated circuit that has a higher measurement bandwidth compared to conventional room temperature electronics. This allowed implementing single shot operations and observe the real-time evolution of the current of a phosphorus-doped silicon single electron transistor that was irradiated with a microwave pulse. Relaxation times up to 90μs are observed, suggesting the presence of well isolated electron excitations within the device. It is expected that these are associated with long decoherence time and the device may be suitable for quantum information processing.
Abstract High-fidelity single-shot readout of spin qubits requires distinguishing states much faster than the T 1 time of the spin state. One approach to improving readout fidelity and bandwidth (BW) is cryogenic amplification, where the signal from the qubit is amplified before noise sources are introduced and room-temperature amplifiers can operate at lower gain and higher BW. We compare the performance of two cryogenic amplification circuits: a current-biased heterojunction bipolar transistor circuit (CB-HBT), and an AC-coupled HBT circuit (AC-HBT). Both circuits are mounted on the mixing-chamber stage of a dilution refrigerator and are connected to silicon metal oxide semiconductor (Si-MOS) quantum dot devices on a printed circuit board (PCB). The power dissipated by the CB-HBT ranges from 0.1 to 1 μ W whereas the power of the AC-HBT ranges from 1 to 20 μ W. Referred to the input, the noise spectral density is low for both circuits, in the 15 to 30 fA/ Hz\sqrt{{\bf{Hz}}}Hz​ Hz range. The charge sensitivity for the CB-HBT and AC-HBT is 330 μ e/ Hz\sqrt{{\bf{Hz}}}Hz​ Hz and 400 μ e/ Hz\sqrt{{\bf{Hz}}}Hz​ Hz , respectively. For the single-shot readout performed, less than 10 μ s is required for both circuits to achieve bit error rates below 10 −3 , which is a putative threshold for quantum error correction.
Quantum bit (qubit) control and readout requires controller-qubit-observer systems for rapid control signal generation and injection to the qubit gates, and observation of their final state projections. Conventionally, for solid-state qubits, this is achieved by generating the control signal at 300 K and transmitting it along very long coaxial cables that span from 300 K to sub-K (typically les 500 mK), then reading out the response from charge proximity sensors such as single-electron transistors along similar lengths of cable. Our approach is to fabricate the classical controller and observer circuits using a commercial foundry processed silicon-on-sapphire (SOS) RFCMOS technology for operation at low temperatures (either at 4.2 K, 1 K, or sub-K). We have demonstrated SOS-CMOS NFET and PFET device operation at 4.2 K, and sub-K that showed deviations from their 300 K characteristics, but with further experiments these were shown to have minimal effects on control circuit function. Using these results, we have fabricated and demonstrated a low-power proof-of-concept SOS-CMOS controller circuit (monostable 100 ps voltage-pulse generator) that can operate at sub-K temperatures in a dilution refrigerator. We briefly discuss experimental and conceptual schemes with which we can develop qubit control systems for cryogenic and lower temperatures. These low temperature experiments also demonstrate that commercial SOS RF-CMOS technology can be feasible for other low temperature and low power applications.