Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Vehicular Technology Conference

Power Allocation and Jammer Selection of a Cooperative Jamming Strategy for Physical-Layer Security

Chin-Liang Wang, Ting-Nan Cho, Feng Liu

Published May 1, 2014• 6 citations
Publisher

Abstract

In this paper, we propose power allocation (PA) and jammer selection schemes based on a cooperative jamming strategy combined with a null-steering beamforming technique (CJ-NB strategy) for physical-layer security. Using the CJ-NB strategy, we first present an asymptotic optimal PA scheme, obtained by solving an achievable secrecy rate maximization problem, and then provide the corresponding achievable secrecy rate analysis. The analysis results show that the maximum achievable secrecy rate will become asymptotically saturated if the number of jammers is large enough. To avoid waste in the use of jammers, we also provide two jammer selection schemes that can determine the minimum number of jammers necessary to achieve almost the same secrecy rate as using all jammers for the CJ-NB strategy with the asymptotic PA scheme. One has lower computational complexity, and the other achieves better performance in reducing the number of jammers used. Finally, simulation results are given to demonstrate the effectiveness of the proposed schemes.

DOI
10.1109/vtcspring.2014.7023057

Related papers

An asymptotic secrecy rate analysis of a cooperative jamming strategy for physical-layer security

Ting-Nan Cho, Chin-Liang Wang

In this paper, we investigate a cooperative jamming strategy combined with a null-steering beamforming technique (CJ-NB strategy) for physical-layer security. To evaluate the achievable secrecy rate, the source input distribution is assumed to be Gaussian, and the achievable secrecy rate can be formulated as an optimization problem for power allocation (PA). By solving the problem, an asymptotically optimal PA is obtained with an exactly closed-form expression. In addition, we provide an asymptotic analysis of the achievable secrecy rate. The asymptotic result shows that the achievable secrecy rate is linearly proportional to the signal-to-noise ratio, but it will become saturated when the number of jammers is high enough. Therefore, we then develop a simple and efficient jammer selection algorithm to find an appropriate jamming set to achieve almost the same performance, but significantly reduce the number of jammers used compared with all the jammers performing the CJ-NB strategy. Finally, we provide simulation results to support our analyses.

International Conference on Communications•Jun 1, 2013•6 citations

Strategy of Relay Selection and Cooperative Jammer Beamforming in Physical Layer Security

Ming Zhang, Yong Shang, Yaohuan Zhao

In this paper, a novel strategy of relay selection and cooperative jammer beamforming is proposed. The proposed scheme selects one node from the intermediate nodes as relay and the rest nodes as friendly jammers. The relay operates in amplify-and-forward (AF) strategy. Jammer weights are derived to null the jamming signals at the destination and relay node and maximize the jamming signal at the eavesdropper. Furthermore, a closed-form optimal solution of power allocation between the selected relay and cooperative jammers is derived. Numerical simulation results show that the proposed scheme can outperform the conventional schemes at the same power consumption.

IEEE Vehicular Technology Conference•Nov 1, 2020•6 citations

Joint Cooperative Beamforming and Jamming for Physical-Layer Security of Decode-and-Forward Relay Networks

Haiyan Guo, Zhen Yang, Linghua Zhang +2 more

This paper proposes a new joint cooperative beamforming and jamming (JCBJ) scheme for improving the physical layer security of decode-and-forward wireless networks where a source node transmits to its destination with the aid of multiple intermediate nodes in the presence of an eavesdropper. In the proposed JCBJ scheme, we select the intermediate nodes succeeding in source decoding as the relays to forward the source transmission simultaneously by employing a beamforming weight vector, and meanwhile, use the remaining ones as the friendly jammers to disturb the eavesdropper by sending artificial noise. In order to achieve the secrecy rate maximum, we further study on the power allocation among the source, relays, and jammers under two assumptions of the wiretap link's channel state information. We derive the closed-form optimal solutions by first allocating the transmit power at the source within different ranges to consider all the possible relay selection schemes in which different numbers of relays are employed, and then transforming the multivariable power allocation problem to a set of single-variable optimization subproblems. Our numerical results show the superiority of the proposed JCBJ scheme and the proposed power allocation strategies.

IEEE Access•Jan 1, 2017•36 citations

Optimal power allocation for joint cooperative beamforming and jamming assisted wireless networks

Haiyan Guo, Zhen Yang, Linghua Zhang +2 more

In this paper, we examine the physical layer security for cooperative wireless networks with multiple intermediate nodes, where the decode-and-forward (DF) protocol is considered. We propose a new joint cooperative beamforming and jamming (JCBJ) scheme to protect wireless communication against eavesdropping, where the intermediate nodes which successfully decode the source signal are selected as the relays for simultaneously forwarding the source signal by employing a weight vector, and meanwhile, the others are used to act as the friendly jammers for broadcasting artificial noise to disturb the eavesdropper. We further investigate the optimal power allocation among the source, relays and friendly jammers for maximizing the secrecy rate of the proposed JCBJ scheme and derive a closed-form sub-optimal solution. Simulation results show that the proposed JCBJ scheme achieves obviously higher secrecy rate than the conventional generalized singular-value-decomposition (GSVD) based beamforming and pure jamming schemes. Additionally, the proposed optimal power allocation scheme performs much better than the equal power allocation scheme in terms of secrecy rate.

International Conference on Communications•May 1, 2017•5 citations

Joint optimal power allocation, cooperative beamforming, and jammer selection design to secure untrusted relaying network

Majid Moradikia, Saeed Mashdour, Ali Jamshidi

Abstract A half‐duplex relaying network provides 2 opportunities for passive eavesdroppers (Eves) and 1 opportunity for untrusted relays to intercept the information. In this paper, we aim to enhance the physical layer security of a cooperative network where a single‐antenna source intends to communicate with a single‐antenna destination in the presence of a group of untrusted relays and a passive eavesdropper. The objective is to protect the data confidentially while concurrently relying on the untrusted relays as potential Eves to improve both the security and reliability of the network. To realize this objective, we design a joint cooperative beamforming and cooperative jamming strategy. With the aim of maximizing the instantaneous secrecy rate, an optimal power allocation (OPA) scheme is proposed where the transmission powers of both jammer and source are optimized simultaneously under the total power budget constraint. To further improve the secrecy rate, a jammer selection strategy is also proposed where cooperative jamming is performed by the destination or one of the idle relays. For the proposed scheme, a closed‐form expression of beamformer vector is derived by solving a generalized eigenvalue problem. Finally, for the OPA problem, it is possible to be neither convex nor concave. In this regard, all possible cases are investigated to determine the OPA factor accurately. Numerical results illustrate that the proposed joint OPA–cooperative beamforming scheme, together with the most appropriate jammer selection strategy, significantly increases the secrecy rate.

Transactions on Emerging Telecommunications Technologies•Jan 18, 2018•11 citations

On Maximizing the Secrecy Rate in a Cooperative Wireless Network using Friendly Jammers

Mohammad Hatami, Hamid Behroozi

In this paper, the security of two-phase relaying system with multiple intermediate nodes in the presence of a malicious eavesdropper is investigated. To enhance the secrecy, a joint cooperative beamforming and jamming combined with relay and jammer selection is proposed. First, the source broadcasts its signal to the relays that are located close to source in a cluster, i.e., the source node uses a small amount of power to broadcast its message locally to other nodes of the cluster, while destination and the eavesdropper are located outside this cluster. In the second phase, two relays transmit re-encoded signal with optimal beamforming such that the secrecy rate is maximized. Simultaneously, two other intermediate nodes (which act as friendly jammers) transmit random jamming signals to degrade the eavesdropper’s channel. Our goal in this paper is to maximize the secrecy rate by applying different methods such as cooperative beamforming, cooperative jamming and relay and jammer selection. To avoid operational complexity, we consider the minimum number of intermediate nodes needed for relaying and jamming without losing the performance, i.e., achieving a non-zero secrecy rate. Cooperative beamforming with multiple relays demands high amount of information exchange and therefore increases the operational complexity. Thus, we aim to reduce the number of relays which take part in cooperative beamforming. Limiting the number of relays may have a bad effect on the coding gain which we compensate it with a proposed selection gain scheme. Numerical results demonstrate the advantage of our proposed scheme compared to the scheme with no cooperative jamming. The main contribution of this work is combining cooperative beamforming and jamming with relay and jammer selection to enhance the physical layer security.

•Sep 1, 2016•1 citation
In this paper, we propose power allocation (PA) and jammer selection schemes based on a cooperative jamming strategy combined with a null-steering beamforming technique (CJ-NB strategy) for physical-layer security. Using the CJ-NB strategy, we first present an asymptotic optimal PA scheme, obtained by solving an achievable secrecy rate maximization problem, and then provide the corresponding achievable secrecy rate analysis. The analysis results show that the maximum achievable secrecy rate will become asymptotically saturated if the number of jammers is large enough. To avoid waste in the use of jammers, we also provide two jammer selection schemes that can determine the minimum number of jammers necessary to achieve almost the same secrecy rate as using all jammers for the CJ-NB strategy with the asymptotic PA scheme. One has lower computational complexity, and the other achieves better performance in reducing the number of jammers used. Finally, simulation results are given to demonstrate the effectiveness of the proposed schemes.
In this paper, we investigate a cooperative jamming strategy combined with a null-steering beamforming technique (CJ-NB strategy) for physical-layer security. To evaluate the achievable secrecy rate, the source input distribution is assumed to be Gaussian, and the achievable secrecy rate can be formulated as an optimization problem for power allocation (PA). By solving the problem, an asymptotically optimal PA is obtained with an exactly closed-form expression. In addition, we provide an asymptotic analysis of the achievable secrecy rate. The asymptotic result shows that the achievable secrecy rate is linearly proportional to the signal-to-noise ratio, but it will become saturated when the number of jammers is high enough. Therefore, we then develop a simple and efficient jammer selection algorithm to find an appropriate jamming set to achieve almost the same performance, but significantly reduce the number of jammers used compared with all the jammers performing the CJ-NB strategy. Finally, we provide simulation results to support our analyses.
In this paper, a novel strategy of relay selection and cooperative jammer beamforming is proposed. The proposed scheme selects one node from the intermediate nodes as relay and the rest nodes as friendly jammers. The relay operates in amplify-and-forward (AF) strategy. Jammer weights are derived to null the jamming signals at the destination and relay node and maximize the jamming signal at the eavesdropper. Furthermore, a closed-form optimal solution of power allocation between the selected relay and cooperative jammers is derived. Numerical simulation results show that the proposed scheme can outperform the conventional schemes at the same power consumption.
This paper proposes a new joint cooperative beamforming and jamming (JCBJ) scheme for improving the physical layer security of decode-and-forward wireless networks where a source node transmits to its destination with the aid of multiple intermediate nodes in the presence of an eavesdropper. In the proposed JCBJ scheme, we select the intermediate nodes succeeding in source decoding as the relays to forward the source transmission simultaneously by employing a beamforming weight vector, and meanwhile, use the remaining ones as the friendly jammers to disturb the eavesdropper by sending artificial noise. In order to achieve the secrecy rate maximum, we further study on the power allocation among the source, relays, and jammers under two assumptions of the wiretap link's channel state information. We derive the closed-form optimal solutions by first allocating the transmit power at the source within different ranges to consider all the possible relay selection schemes in which different numbers of relays are employed, and then transforming the multivariable power allocation problem to a set of single-variable optimization subproblems. Our numerical results show the superiority of the proposed JCBJ scheme and the proposed power allocation strategies.
In this paper, we examine the physical layer security for cooperative wireless networks with multiple intermediate nodes, where the decode-and-forward (DF) protocol is considered. We propose a new joint cooperative beamforming and jamming (JCBJ) scheme to protect wireless communication against eavesdropping, where the intermediate nodes which successfully decode the source signal are selected as the relays for simultaneously forwarding the source signal by employing a weight vector, and meanwhile, the others are used to act as the friendly jammers for broadcasting artificial noise to disturb the eavesdropper. We further investigate the optimal power allocation among the source, relays and friendly jammers for maximizing the secrecy rate of the proposed JCBJ scheme and derive a closed-form sub-optimal solution. Simulation results show that the proposed JCBJ scheme achieves obviously higher secrecy rate than the conventional generalized singular-value-decomposition (GSVD) based beamforming and pure jamming schemes. Additionally, the proposed optimal power allocation scheme performs much better than the equal power allocation scheme in terms of secrecy rate.
Abstract A half‐duplex relaying network provides 2 opportunities for passive eavesdroppers (Eves) and 1 opportunity for untrusted relays to intercept the information. In this paper, we aim to enhance the physical layer security of a cooperative network where a single‐antenna source intends to communicate with a single‐antenna destination in the presence of a group of untrusted relays and a passive eavesdropper. The objective is to protect the data confidentially while concurrently relying on the untrusted relays as potential Eves to improve both the security and reliability of the network. To realize this objective, we design a joint cooperative beamforming and cooperative jamming strategy. With the aim of maximizing the instantaneous secrecy rate, an optimal power allocation (OPA) scheme is proposed where the transmission powers of both jammer and source are optimized simultaneously under the total power budget constraint. To further improve the secrecy rate, a jammer selection strategy is also proposed where cooperative jamming is performed by the destination or one of the idle relays. For the proposed scheme, a closed‐form expression of beamformer vector is derived by solving a generalized eigenvalue problem. Finally, for the OPA problem, it is possible to be neither convex nor concave. In this regard, all possible cases are investigated to determine the OPA factor accurately. Numerical results illustrate that the proposed joint OPA–cooperative beamforming scheme, together with the most appropriate jammer selection strategy, significantly increases the secrecy rate.
In this paper, the security of two-phase relaying system with multiple intermediate nodes in the presence of a malicious eavesdropper is investigated. To enhance the secrecy, a joint cooperative beamforming and jamming combined with relay and jammer selection is proposed. First, the source broadcasts its signal to the relays that are located close to source in a cluster, i.e., the source node uses a small amount of power to broadcast its message locally to other nodes of the cluster, while destination and the eavesdropper are located outside this cluster. In the second phase, two relays transmit re-encoded signal with optimal beamforming such that the secrecy rate is maximized. Simultaneously, two other intermediate nodes (which act as friendly jammers) transmit random jamming signals to degrade the eavesdropper’s channel. Our goal in this paper is to maximize the secrecy rate by applying different methods such as cooperative beamforming, cooperative jamming and relay and jammer selection. To avoid operational complexity, we consider the minimum number of intermediate nodes needed for relaying and jamming without losing the performance, i.e., achieving a non-zero secrecy rate. Cooperative beamforming with multiple relays demands high amount of information exchange and therefore increases the operational complexity. Thus, we aim to reduce the number of relays which take part in cooperative beamforming. Limiting the number of relays may have a bad effect on the coding gain which we compensate it with a proposed selection gain scheme. Numerical results demonstrate the advantage of our proposed scheme compared to the scheme with no cooperative jamming. The main contribution of this work is combining cooperative beamforming and jamming with relay and jammer selection to enhance the physical layer security.