Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Japanese Journal of Applied Physics

Heterodyne Detection of Microwaves Using Granular-Type Y1Ba2Cu3O7-x Superconductors

Yorinobu Yoshisato, Akio Takeoka, Minoru Takai, Kazuya Niki, Shuichi Yoshikawa, Toshimasa Hirano, Shoichi Nakano

Published Apr 1, 1991• 10 citations
Publisher

Abstract

A heterodyne mixing experiment of microwaves at about 20 GHz was performed using a microwave detector made from granular-type Y1Ba2Cu3O7-x (YBCO) superconductors. Although the bridge included many boundaries, voltage steps corresponding to the Josephson frequency and step height dependence for microwave power similar to those of a single weak-link bridge were clearly observed. The IF signal showed peak amplitudes corresponding to the peak dynamic resistantance due to nonlinearity resulting from the Josephson effect. It was confirmed for the first time that this detector operates stably for the heterodyne mixer at 60 K or below and has a potential for high sensitivity due to its large dynamic resistance.

DOI
10.1143/jjap.30.661

Related papers

Mixing characteristics of a microwave detector using a granular YBCO superconductor

Yorinobu Yoshisato, Minoru Takai, Kazuya Niki +3 more

Microbridge-type Josephson junctions made of granular bulk YBCO superconductors were experimentally studied at microwave frequencies. Although the bridge included many grain boundaries, clear Shapiro steps were induced at every hf/2e voltage for microwave frequencies, and step height dependence for microwave power similar to that of a single weak link bridge was observed. A heterodyne mixing experiment of microwaves at about 20 GHz was also performed using the detector. The IF signal showed peak amplitudes corresponding to the peak dynamic resistance due to nonlinearity resulting from the Josephson effect. It was confirmed that the detector operates stably for the Josephson-effect heterodyne mixer at 60 K or below. The detector has potential for high sensitivity and good impedance matching due to its large dynamic resistance and high normal state resistance, respectively.

IEEE Transactions on Magnetics•Mar 1, 1991•6 citations

Millimeter-wave detection by GBJJ using high-T/sub c/ superconducting YBaCuO films

S. Kita, H. Tanabe, Takeshi Kobayashi

Millimeter-wave detection in the heterodyne mixing mode has been carried out using the high-T/sub c/ superconducting GBJJ (grain boundary Josephson junction). The GBJJ was fabricated from high T/sub c/ superconducting Y-Ba-Cu-O films, prepared on YSZ and SrTiO/sub 3/ substrates using an RF sputtering technique. The junction was patterned by chemical wet etching with phosphoric acid solution. The authors carried out experiments in the heterodyne mixing mode for a signal of 35 GHz with local oscillation at 34.97 GHz. The detected IF (intermediate frequency) output power was obtained at a bias voltage lying midway between the zeroth and first Shapiro steps. A mixer conversion efficiency of -15 dB was obtained with a dynamic range of about 20 dB at 35 GHz. This result strongly implies that high-T/sub c/ superconducting GBJJ works well as a detector at millimeter-wave frequencies.>

IEEE Transactions on Magnetics•Mar 1, 1989•16 citations

Heterodyne mixing with a sandwich-type Josephson junction using a Bi-based high- oxide superconductor

K Mizuno, Hidetaka Higashino, Kentaro Setsune

A sandwich-type high- Josephson junction coupled with a coplanar-type transmission line was fabricated and heterodyne mixing characteristics were investigated. The junction was fabricated from a stacked film structure of (BSCCO/BSNCO/BSCCO) and the transmission line was made of sputter-deposited Pt film. The junction had a rectangular shape of . Current - voltage (I - V) curves of the junction showed weak-link-type characteristics. Two microwave sources of a frequency synthesizer and a sweep oscillator were used as a local oscillator (LO: 20 GHz) and a radio frequency signal source (RF: 19 GHz) for heterodyne mixing experiments. Intermediate signal (IF: 1 GHz) was transmitted through the transmission line and detected by a power meter. The conversion efficiency of -44 dB was estimated for an LO oscillator level of -23 dB m at 5.7 K when the junction was biased at the point below the first Shapiro step.

Superconductor Science and Technology•Apr 1, 1996•2 citations

Microwave detection and mixing in Y-Ba-Cu-O thin films at liquid-nitrogen temperatures

Janusz Konopka, Roman Sobolewski, Anna Konopka +1 more

Microwave properties of an Y-Ba-Cu-O microstrip detector have been studied at 24 GHz frequency band at the liquid-nitrogen temperature. The amplitude of the video detection signal was found to be proportional to the incident microwave power. Direct mixing action was also demonstrated, setting the upper limit for the film response time as short as 40 ps. Occurrence of microwave mixing in the absence of dc current bias was observed, suggesting the presence of the inverse Josephson effect. Physical properties of the detector response were very similar to the enhanced mode of detection, characteristic for granular superconducting films.

Applied Physics Letters•Aug 29, 1988•24 citations

Conversion gain and noise of YBa/sub 2/Cu/sub 3/O/sub 7/ weak-link mixers

Donald P. Butler, Jiaqi Wang, Anil Bhandari +1 more

Microwave mixing and parametric conversion in YBa/sub 2/Cu/sub 3/O/sub 7/ microbridges were investigated. The devices have been operated as down-converters, converting a 20-GHz radio frequency to a 1.5-GHz intermediate frequency under the action of an 18.5-GHz local oscillator. The microbridges were fabricated both as granular films on MgO substrates possessing grain boundary weak links and as epitaxial films deposited over substrate steps in LaAlO/sub 3/ substrates. The authors have measured conversion gains as high as -8+or-4 dB when mixing on the nonlinear resistive (superconducting-normal) transition and as high as -30 to -40 dB when parametrically converting via the nonlinear inductance of the bridge at bias currents less than the critical current. Output referred noise powers as low as -206 dB/Hz (3*10/sup -21/ W/Hz) have been measured. In some samples, noise switching events were observed.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•5 citations

YBCO microwave grain boundary mixer using a SrTiO/sub 3/ bicrystal substrate

R. Seed, Paul C. Dorsey, Hoton How +2 more

A microwave mixer was patterned on a microstrip transmission line of superconducting YBCO (YBa/sub 2/Cu/sub 3/O/sub 7-x/). The YBCO film was epitaxially laser deposited on a SrTiO/sub 3/ bicrystal substrate. A weak link was constructed by patterning a microbridge in the microstrip at the bicrystal boundary. Microwave signals at 9.000 GHz and 9.941 GHz were applied at the input of the microstrip line. An output intermediate frequency signal was observed at 941 MHz and was detected as the transmitted signal. The microbridge junction, which behaved as a resistively shunted Josephson junction (RSJ), was current biased slightly above the critical current I/sub c/. The mixer conversion loss was measured at the input and output ports of the device package. The mixing efficiency was determined at the device junction. This efficiency was compared with the calculated efficiency determined by numerical solution of the Josephson equation for the weak link junction.>

IEEE Transactions on Magnetics•Nov 1, 1993•4 citations
A heterodyne mixing experiment of microwaves at about 20 GHz was performed using a microwave detector made from granular-type Y1Ba2Cu3O7-x (YBCO) superconductors. Although the bridge included many boundaries, voltage steps corresponding to the Josephson frequency and step height dependence for microwave power similar to those of a single weak-link bridge were clearly observed. The IF signal showed peak amplitudes corresponding to the peak dynamic resistantance due to nonlinearity resulting from the Josephson effect. It was confirmed for the first time that this detector operates stably for the heterodyne mixer at 60 K or below and has a potential for high sensitivity due to its large dynamic resistance.
Microbridge-type Josephson junctions made of granular bulk YBCO superconductors were experimentally studied at microwave frequencies. Although the bridge included many grain boundaries, clear Shapiro steps were induced at every hf/2e voltage for microwave frequencies, and step height dependence for microwave power similar to that of a single weak link bridge was observed. A heterodyne mixing experiment of microwaves at about 20 GHz was also performed using the detector. The IF signal showed peak amplitudes corresponding to the peak dynamic resistance due to nonlinearity resulting from the Josephson effect. It was confirmed that the detector operates stably for the Josephson-effect heterodyne mixer at 60 K or below. The detector has potential for high sensitivity and good impedance matching due to its large dynamic resistance and high normal state resistance, respectively.
Millimeter-wave detection in the heterodyne mixing mode has been carried out using the high-T/sub c/ superconducting GBJJ (grain boundary Josephson junction). The GBJJ was fabricated from high T/sub c/ superconducting Y-Ba-Cu-O films, prepared on YSZ and SrTiO/sub 3/ substrates using an RF sputtering technique. The junction was patterned by chemical wet etching with phosphoric acid solution. The authors carried out experiments in the heterodyne mixing mode for a signal of 35 GHz with local oscillation at 34.97 GHz. The detected IF (intermediate frequency) output power was obtained at a bias voltage lying midway between the zeroth and first Shapiro steps. A mixer conversion efficiency of -15 dB was obtained with a dynamic range of about 20 dB at 35 GHz. This result strongly implies that high-T/sub c/ superconducting GBJJ works well as a detector at millimeter-wave frequencies.>
A sandwich-type high- Josephson junction coupled with a coplanar-type transmission line was fabricated and heterodyne mixing characteristics were investigated. The junction was fabricated from a stacked film structure of (BSCCO/BSNCO/BSCCO) and the transmission line was made of sputter-deposited Pt film. The junction had a rectangular shape of . Current - voltage (I - V) curves of the junction showed weak-link-type characteristics. Two microwave sources of a frequency synthesizer and a sweep oscillator were used as a local oscillator (LO: 20 GHz) and a radio frequency signal source (RF: 19 GHz) for heterodyne mixing experiments. Intermediate signal (IF: 1 GHz) was transmitted through the transmission line and detected by a power meter. The conversion efficiency of -44 dB was estimated for an LO oscillator level of -23 dB m at 5.7 K when the junction was biased at the point below the first Shapiro step.
Microwave properties of an Y-Ba-Cu-O microstrip detector have been studied at 24 GHz frequency band at the liquid-nitrogen temperature. The amplitude of the video detection signal was found to be proportional to the incident microwave power. Direct mixing action was also demonstrated, setting the upper limit for the film response time as short as 40 ps. Occurrence of microwave mixing in the absence of dc current bias was observed, suggesting the presence of the inverse Josephson effect. Physical properties of the detector response were very similar to the enhanced mode of detection, characteristic for granular superconducting films.
Microwave mixing and parametric conversion in YBa/sub 2/Cu/sub 3/O/sub 7/ microbridges were investigated. The devices have been operated as down-converters, converting a 20-GHz radio frequency to a 1.5-GHz intermediate frequency under the action of an 18.5-GHz local oscillator. The microbridges were fabricated both as granular films on MgO substrates possessing grain boundary weak links and as epitaxial films deposited over substrate steps in LaAlO/sub 3/ substrates. The authors have measured conversion gains as high as -8+or-4 dB when mixing on the nonlinear resistive (superconducting-normal) transition and as high as -30 to -40 dB when parametrically converting via the nonlinear inductance of the bridge at bias currents less than the critical current. Output referred noise powers as low as -206 dB/Hz (3*10/sup -21/ W/Hz) have been measured. In some samples, noise switching events were observed.>
A microwave mixer was patterned on a microstrip transmission line of superconducting YBCO (YBa/sub 2/Cu/sub 3/O/sub 7-x/). The YBCO film was epitaxially laser deposited on a SrTiO/sub 3/ bicrystal substrate. A weak link was constructed by patterning a microbridge in the microstrip at the bicrystal boundary. Microwave signals at 9.000 GHz and 9.941 GHz were applied at the input of the microstrip line. An output intermediate frequency signal was observed at 941 MHz and was detected as the transmitted signal. The microbridge junction, which behaved as a resistively shunted Josephson junction (RSJ), was current biased slightly above the critical current I/sub c/. The mixer conversion loss was measured at the input and output ports of the device package. The mixing efficiency was determined at the device junction. This efficiency was compared with the calculated efficiency determined by numerical solution of the Josephson equation for the weak link junction.>