Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEICE Electronics Express

Zero-crossing Shapiro step generated in a niobium in-line Josephson gate

Yoshinao Mizugaki, Haruna Takahashi, Hiroshi Shimada

Published Jan 1, 2014• 2 citations
Publisher

Abstract

We demonstrate a zero-crossing Shapiro step generated in a magnetically-coupled Josephson gate, where a long Josephson junction and a control line are placed in-line. The operation is based on the imbalanced evolution of the junction phases owing to the different amplitudes of the positive and negative critical current. A test circuit was fabricated using a Nb/AlOx/Nb junction technology. When we applied a rf signal of 15.2GHz, we observed a Shapiro step that crossed the zero-current axis at the voltage position of the 1st order. The experimental results were quantitatively reproduced by simulation.

DOI
10.1587/elex.11.20140054

Related papers

Zero-Crossing Shapiro Step in Asymmetric Two-Junction Superconducting Quantum Interference Device

Yoshinao Mizugaki, Kazuyuki Katoh, Masataka Moriya +2 more

We demonstrate a zero-crossing Shapiro step in an asymmetric two-junction superconducting quantum interference device (SQUID) driven by one sinusoidal RF signal. The operation is based on the imbalanced evolution of the junction phases due to the tilted interference diagrams. A test circuit was fabricated using Nb/AlO x /Nb junction technology. When we applied an RF signal of 10 GHz, we observed a Shapiro step crossing the zero-current axis at the voltage position of the first order. The polarity of the step voltage was switched by a DC control flux to the SQUID loop. The experimental current–voltage curves were quantitatively reproduced by simulation.

Japanese Journal of Applied Physics•Jun 16, 2006•3 citations

Zero-crossing Shapiro step generated in an asymmetric and nonhysteretic rf-current-driven two-junction superconducting quantum interference device

Yoshinao Mizugaki, Kazuyuki Katoh

A zero-crossing Shapiro step (ZCSS) in an asymmetric and nonhysteretic two-junction superconducting quantum interference device (SQUID) driven by one sinusoidal rf signal is presented. The operation is based on imbalanced evolution of the junction phases owing to the tilted interference diagrams. Dependence of ZCSS generation upon the frequency and amplitude of a rf signal was numerically obtained. A test circuit was designed and fabricated using a Nb∕AlOx∕Nb junction technology. When we irradiated a rf signal of 10GHz, a ZCSS at the voltage position of the first order was observed. The polarity of the step voltage was switched by a dc control flux to the SQUID loop. The experimental bias-current versus voltage and control-current versus voltage curves were quantitatively reproduced by numerical simulation.

Journal of Applied Physics•Sep 15, 2006•7 citations

Zero-crossing shapiro step in a three-junction SQUID magnetically coupled with two phase-shifted RF signals

Yoshinao Mizugaki, Jian Chen, S. Nishikata +3 more

We demonstrate a zero-crossing Shapiro step in a three-junction SQUID (3J-SQUID) coupled with two phase-shifted RF signals. The operation is based on periodic flux quantum transitions in the 3J-SQUID under the zero- and negatively-biasing conditions. A test circuit is fabricated using a Nb/AlO/sub x//Nb junction technology. When we feed RF signals up to 10.5 GHz, we observe a Shapiro step crossing the zero-current axis at the voltage position of the 1st order. The experimental current-voltage characteristics are quantitatively reproduced by simulation. Zero-crossing conditions for the DC offset flux and the RF power are obtained experimentally, which is also confirmed by simulation. A programmable Josephson voltage standard is discussed as one of the possible applications.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•3 citations

Bipolar Quantum Voltage Generator Based on Zero Crossing Shapiro Steps in Asymmetric 2J-SQUIDs

Masataka Moriya, Naoki Kondo, Yoshinao Mizugaki

On an asymmetric two-junction superconducting quantum interference device (2J-SQUID) driven by one sinusoidal rf signal, the observation of zero-crossing Shapiro steps have been reported. In this paper, the loop inductance, L and the ratio of critical currents of Josephson junctions of the 2J-SQUID were optimized by a simulation. Using three voltage states those this asymmetric 2J-SQUID has, the bipolar quantum voltage generator that has three asymmetric 2J-SQUIDs and two control lines, was designed based on obtained parameters. Within the bias current -voltage curves with seven different combinations of the control currents, seven quantized voltages were obtained at the zero bias current.

Physics Procedia•Jan 1, 2012•0 citations

Observation of Zero Crossing Shapiro Step on Current-Voltage Curve of Long YBa2Cu3O7-delta Bicrystal Josephson Junction Having Tilted Field Dependence

Masataka Moriya, Tokuyama Takato, Haruna Takahashi +1 more

A YBa2Cu3O7-δbicrystal Josephson junction was fabricated by electron beam lithography and Ar ion beam etching. The width of the junction (W) was 12 μm and the Josephson penetration length (λJ) was calculated to be 2.36 μm. As W/λJis 5.1, this bicrystal junction is a long Josephson junction. In critical current - magnetic field characteristics, periodicity is not observed, but the maximum value and the minimum value of the critical current are different at a finite magnetic field. In the I-V curve with irradiating the rf signal, the rounded Shapiro step was observed. By applying the magnetic field, the rounded 1st Shapiro step across the zero current axis was observed.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2015•0 citations

Numerical simulation of quantized voltage steps in overdamped josephson junctions controlled by simple pulse codes

A. Takada

Shapiro steps crossing the zero-current axis, i.e., zero-crossing steps, in the overdamped Josephson junction driven with a simple pulse code consisting of single and multiple pulses in each repetition period are studied based on numerical simulations. In this study, it is confirmed that the quantized voltage at which the zero-crossing step appears can be controlled by the number of the additional pulses without changing current bias range. The case in which the additional pulses having small fluctuations in phase is also considered. No visible effect of the fluctuations on the current position of the Shapiro steps is observed, so that the current range with respect to the phase lock between the Josephson oscillation and the pulse code is determined by the number of pulses.

IEEE Transactions on Applied Superconductivity•Dec 1, 2003•0 citations
We demonstrate a zero-crossing Shapiro step generated in a magnetically-coupled Josephson gate, where a long Josephson junction and a control line are placed in-line. The operation is based on the imbalanced evolution of the junction phases owing to the different amplitudes of the positive and negative critical current. A test circuit was fabricated using a Nb/AlOx/Nb junction technology. When we applied a rf signal of 15.2GHz, we observed a Shapiro step that crossed the zero-current axis at the voltage position of the 1st order. The experimental results were quantitatively reproduced by simulation.
We demonstrate a zero-crossing Shapiro step in an asymmetric two-junction superconducting quantum interference device (SQUID) driven by one sinusoidal RF signal. The operation is based on the imbalanced evolution of the junction phases due to the tilted interference diagrams. A test circuit was fabricated using Nb/AlO x /Nb junction technology. When we applied an RF signal of 10 GHz, we observed a Shapiro step crossing the zero-current axis at the voltage position of the first order. The polarity of the step voltage was switched by a DC control flux to the SQUID loop. The experimental current–voltage curves were quantitatively reproduced by simulation.
A zero-crossing Shapiro step (ZCSS) in an asymmetric and nonhysteretic two-junction superconducting quantum interference device (SQUID) driven by one sinusoidal rf signal is presented. The operation is based on imbalanced evolution of the junction phases owing to the tilted interference diagrams. Dependence of ZCSS generation upon the frequency and amplitude of a rf signal was numerically obtained. A test circuit was designed and fabricated using a Nb∕AlOx∕Nb junction technology. When we irradiated a rf signal of 10GHz, a ZCSS at the voltage position of the first order was observed. The polarity of the step voltage was switched by a dc control flux to the SQUID loop. The experimental bias-current versus voltage and control-current versus voltage curves were quantitatively reproduced by numerical simulation.
We demonstrate a zero-crossing Shapiro step in a three-junction SQUID (3J-SQUID) coupled with two phase-shifted RF signals. The operation is based on periodic flux quantum transitions in the 3J-SQUID under the zero- and negatively-biasing conditions. A test circuit is fabricated using a Nb/AlO/sub x//Nb junction technology. When we feed RF signals up to 10.5 GHz, we observe a Shapiro step crossing the zero-current axis at the voltage position of the 1st order. The experimental current-voltage characteristics are quantitatively reproduced by simulation. Zero-crossing conditions for the DC offset flux and the RF power are obtained experimentally, which is also confirmed by simulation. A programmable Josephson voltage standard is discussed as one of the possible applications.
On an asymmetric two-junction superconducting quantum interference device (2J-SQUID) driven by one sinusoidal rf signal, the observation of zero-crossing Shapiro steps have been reported. In this paper, the loop inductance, L and the ratio of critical currents of Josephson junctions of the 2J-SQUID were optimized by a simulation. Using three voltage states those this asymmetric 2J-SQUID has, the bipolar quantum voltage generator that has three asymmetric 2J-SQUIDs and two control lines, was designed based on obtained parameters. Within the bias current -voltage curves with seven different combinations of the control currents, seven quantized voltages were obtained at the zero bias current.
A YBa2Cu3O7-δbicrystal Josephson junction was fabricated by electron beam lithography and Ar ion beam etching. The width of the junction (W) was 12 μm and the Josephson penetration length (λJ) was calculated to be 2.36 μm. As W/λJis 5.1, this bicrystal junction is a long Josephson junction. In critical current - magnetic field characteristics, periodicity is not observed, but the maximum value and the minimum value of the critical current are different at a finite magnetic field. In the I-V curve with irradiating the rf signal, the rounded Shapiro step was observed. By applying the magnetic field, the rounded 1st Shapiro step across the zero current axis was observed.
Shapiro steps crossing the zero-current axis, i.e., zero-crossing steps, in the overdamped Josephson junction driven with a simple pulse code consisting of single and multiple pulses in each repetition period are studied based on numerical simulations. In this study, it is confirmed that the quantized voltage at which the zero-crossing step appears can be controlled by the number of the additional pulses without changing current bias range. The case in which the additional pulses having small fluctuations in phase is also considered. No visible effect of the fluctuations on the current position of the Shapiro steps is observed, so that the current range with respect to the phase lock between the Josephson oscillation and the pulse code is determined by the number of pulses.