Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of the Optical Society of America A

Quantum-limited optical phase detection at the 10^-10-rad level

Brian T. Lantz, Peter K Fritschel, Haisheng Rong, Edward J. Daw, Gabriela I. González

Published Jan 1, 2002• 11 citations
Publisher

Abstract

Interferometric detection of gravitational waves at a level of astrophysical interest is expected to require measurement of optical phase differences of < or = 10(-10) rad. A fundamental limit to the phase sensing is the statistics of photon detection--Poisson statistics for light in a coherent state. We have built a laboratory-scale interferometer to achieve and investigate the phase detection sensitivity required for the Laser Interferometer Gravitational-Wave Observatory. With 70 W of circulating power, we have obtained a phase sensitivity of 1.28 x 10(-10) rad/square root(Hz) at frequencies above 600 Hz, limited by quantum noise. Below 600 Hz, excess noise above the quantum limit is seen, and we present our investigations into the sources of this excess. Compared with the results of previous such experiments, the phase sensitivity over the full 100-Hz-10-kHz band of interest has been improved by factors of up to 100, with a factor-of-2.5 improvement in the quantum-limited level.

DOI
10.1364/josaa.19.000091

Related papers

High Power Interferometric Phase Measurement Limited by Quantum Noise and Application to Detection of Gravitational Waves

Peter K Fritschel, Gabriela I. González, Brian T. Lantz +2 more

Interferometric detection of gravitational waves at levels of astrophysical interest is expected to require measurement of optical phase differences of $\ensuremath{\le}{10}^{\ensuremath{-}10}$ rad. To achieve this sensitivity the measurement must be made at the quantum (shot noise) limit. We have built a laboratory-scale interferometer to investigate limits to sensing the phase at this level, and obtained, with 70 W of circulating power, a phase sensitivity limited by shot noise of $3\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}10}\phantom{\rule{0ex}{0ex}}\mathrm{rad}/\sqrt{\mathrm{Hz}}$ at frequencies above 1.5 kHz. We describe the experiment and discuss the implications for the Laser Interferometer Gravitational-Wave Observatory (LIGO).

Physical Review Letters•Apr 13, 1998•38 citations

Quantum limited optical phase detection in a high-power suspended interferometer

Brian T. Lantz

The LIGO project (Laser Interferometer Gravitational-Wave Observatory) is currently engaged in the construction of a new observatory to measure gravitational radiation from astrophysical sources. The first generation of interferometric gravitational wave antennas is scheduled to come on-line in 2001. With an initial noise level of ... at frequencies around 200Hz, these antennas represent the most sensitive instruments ever constructed for the detection of gravitational radiation, To achieve the required sensitivity, the antennas are configured as recycled Michelson Interferometers with Fabry-Perot cavities in the Michelson arms. One of the fundamental limits associated with an instrument of this type is the ability to detect differential phase shifts between the beams returning to the beamsplitter from the Fabry-Perot arm cavities. To achieve the planned sensitivity to gravitational radiation, this detection should be limited only by photon courting statistics ("shot noise") at a level of ... between 150Hz and 10kHT. The goal of this work is to develop and demonstrate the techniques which are necessary to achieve this optical phase sensitivity. A prototype recycled Michelson interferometer was constructed which reached an optical phase sensitivity of ... above 600 Hz. This thesis describes the methods used to achieve this optical phase sensitivity, and details the lessons learned from operating the prototype instrument. We pay particular attention to interferometric control of suspended optics, laser frequency control, and thermal lensing.

•Jan 1, 1999•6 citations

Quantum enhancement of a 4km laser interferometer gravitational-wave detector

S. Chua

The ability to directly detect gravitational waves will open a completely new branch of astronomy to view the Universe, one that is inaccessible to electromagnetic-based astronomy. First generation ground-based interferometric gravitational-wave detectors have achieved strain sensitivities of order one part in ten to the twenty-one, at 100 Hz detection frequency. A new generation of detectors are under construction, designed to improve on the sensitivity of the first-generation detectors by a factor of 10. The quantum nature of light will broadly limit the sensitivity of these new instruments. This quantum noise will originate from the quantum vacuum fluctuations that enter the unused port of the interferometer. One of the most promising options for reducing the quantum noise impact and further increasing the sensitivity is applying quantum squeezed vacuum states. These squeezed states have lower noise in one quadrature than the vacuum state. By replacing the quantum vacuum fluctuations entering the interferometer with squeezed vacuum states, the quantum noise impact is reduced. This thesis firstly details the development of a squeezed light source that produces squeezed states applicable for enhancing interferometric gravitational-wave detectors. A doubly-resonant, travelling-wave bow-tie cavity squeezed light source is presented. For the first time, greater than 10 dB of quantum noise suppression across the gravitational-wave detection band is directly observed, and 11.6 dB of quantum noise suppression is observed above 200 Hz. This squeezing cavity design also has benefits with intrinsic isolation to backscattered light. Experiments that quantify this isolation are reported. The properties affecting squeezing magnitude and low-frequency squeezing measurement are discussed. In addition, a modified squeezing-ellipse-phase control technique for squeezed vacuum states is presented. This thesis secondly presents results from the LIGO Squeezed Light Injection Experiment, undertaken to test squeezed light injection into a 4 km interferometric gravitational-wave detector. The results of the experiment show the first measurement of squeezing-enhancement in a 4 km gravitational-wave detector, with 2.15 dB measured above 250 Hz. This represents the best sensitivity to gravitational waves yet achieved at these frequencies by any single gravitational-wave detector to date. An unknown area was whether the addition of a squeezer would introduce noise couplings that degrade the crucial low frequency sensitivity. The results demonstrate that injected squeezed states are compatible with low frequency gravitational-wave measurement. The characterisation of squeezing-injection optical losses and fluctuations of the squeezing angle are also reported. The knowledge and processes gained, from both the squeezed light source development work and the LIGO Squeezed Light Injection Experiment, will inform the design, planning and implementation of squeezed states in future gravitational-wave detectors.

•Jan 1, 2013•1 citation

50-km fiber interferometer for testing gravitational signatures in quantum interference

Haocun Yu, Dorotea Macri, Thomas Morling +10 more

Quantum mechanics and general relativity are the foundational pillars of modern physics, yet experimental tests that combine the two frameworks remain rare. Measuring optical phase shifts of massless photons in a gravitational potential provides a unique quantum platform to probe gravity beyond Newtonian descriptions, but laboratory-based interferometers have not yet reached the sensitivity needed to access this regime. Here, we report the realization of a 50-km table-top Mach-Zehnder fiber interferometer operating at the single-photon level, achieving a phase sensitivity of $4.42\times10^{-6}$ rad root-mean-square (RMS) within the frequency range of 0.01 Hz to 5 Hz. We demonstrate that this sensitivity is sufficient to resolve a phase-shift signal of $(6.18 \pm 0.44)\times10^{-5}$ rad RMS at 0.1 Hz, associated with a modulated gravity-induced signal. Our results establish a milestone for quantum sensing with large-scale optical interferometry, demonstrating the capability to detect gravitational redshifts in a local laboratory, thereby paving the way for testing quantum phenomena within general relativistic frameworks.

quant-pharXiv:2511.17022•Physical Review Letters•Nov 24, 2025•4 citations

Gravitational wave detection using laser interferometry beyond the standard quantum limit

M. Heurs

Interferometric gravitational wave detectors (such as advanced LIGO) employ high-power solid-state lasers to maximize their detection sensitivity and hence their reach into the universe. These sophisticated light sources are ultra-stabilized with regard to output power, emission frequency and beam geometry; this is crucial to obtain low detector noise. However, even when all laser noise is reduced as far as technically possible, unavoidable quantum noise of the laser still remains. This is a consequence of the Heisenberg Uncertainty Principle, the basis of quantum mechanics: in this case, it is fundamentally impossible to simultaneously reduce both the phase noise and the amplitude noise of a laser to arbitrarily low levels. This fact manifests in the detector noise budget as two distinct noise sources—photon shot noise and quantum radiation pressure noise—which together form a lower boundary for current-day gravitational wave detector sensitivities, the standard quantum limit of interferometry. To overcome this limit, various techniques are being proposed, among them different uses of non-classical light and alternative interferometer topologies. This article explains how quantum noise enters and manifests in an interferometric gravitational wave detector, and gives an overview of some of the schemes proposed to overcome this seemingly fundamental limitation, all aimed at the goal of higher gravitational wave event detection rates. This article is part of a discussion meeting issue ‘The promises of gravitational-wave astronomy’.

Philosophical Transactions of the Royal Society A Mathematical Physical and Engineering Sciences•Apr 16, 2018•11 citations

Quantum limited measurements in gravitational wave detectors

Andrew R. Wade

Gravitational waves manifest as a time varying straining of space: they arise from the accelerating motions of large bodies of mass and propagate across the universe at the speed of light as ripples in the fabric of space-time, a fleetingly weak effect so far eluding direct detection. The detection of gravitation waves is expected to yield a rich vein to observational astronomy, complementing existing electromagnetic surveys and revealing a hitherto unexplored range of phenomena. First generation interferometric gravitational wave detectors, notably Enhanced LIGO, achieved strain sensitivities of one part in ten to power twenty-one per square-root-Hertz at 100 Hz with an expected detection rate of 2-3 events per year. Commissioning of a new generation of Advanced LIGO interferometric detectors has concluded recently with a resultant ten-fold sensitivity improvement. Overall their potential event detection space has increased by a factor of 1000. The quantum nature of light within these detectors now limits their sensitivity over most of their frequency range. This quantum noise limit is driven by the vacuum quadrature fluctuations propagated through their open detection ports and represents a fundamental noise floor to their strain sensitivity. This thesis addresses two distinct approaches to quantum noise improvement for future upgrades to advanced detectors. The first addresses the issue of quantum noise by adopting a quantum non-demolition approach to detector readout variables, the so-called `speed-meter’ design. Such a modified instrument samples test mass momentum, a quantity for which time separated measurements commute and are therefore not bound by Heisenberg-like limits. A novel polarisation-folded sloshing cavity type speed-meter is proposed where readout fields are stored and delayed in the orthogonal polarisation of the interferometer’s arms cavities. Here frequency dependence is selected to cancel position like measurements so that only test mass momentum information remains. A quantum noise propagation model is developed and a sensitivity performance is demonstrated that beats the standard quantum limit below 100 Hz over a broad range of frequencies. A second approach to achieve quantum noise enhancement in advanced detectors involves injection of quadrature-squeezed states in the place of vacuum. This dissertation details the development of a prototype squeezed vacuum source suitable to the demanding enhancement requirements for an Advanced LIGO squeezing installation. The construction of a doubly resonant, bow-tie cavity source is presented. This employs a novel monolithic all-glass cavity construction and is vacuum compatible. This design demonstrates the viability of building a cavity using optical contacting as a construction technique for attaching mounting prisms to highly polished fused-silica breadboards. Such a design can be expected to have excellent length noise stability, provide low intrinsic phase noise and would be suitable to mount on seismic isolation stages within the LIGO vacuum envelope. Further, the travelling wave cavity design should provide excellent 50 dB intrinsic backscatter isolation. We demonstrate the first operation of such a complex non-linear device under vacuum, producing 8.6 dB of measured vacuum squeezing down to 10 Hz across the advanced LIGO ‘audio-band’ detection range.

•Jan 1, 2016•1 citation
Interferometric detection of gravitational waves at a level of astrophysical interest is expected to require measurement of optical phase differences of < or = 10(-10) rad. A fundamental limit to the phase sensing is the statistics of photon detection--Poisson statistics for light in a coherent state. We have built a laboratory-scale interferometer to achieve and investigate the phase detection sensitivity required for the Laser Interferometer Gravitational-Wave Observatory. With 70 W of circulating power, we have obtained a phase sensitivity of 1.28 x 10(-10) rad/square root(Hz) at frequencies above 600 Hz, limited by quantum noise. Below 600 Hz, excess noise above the quantum limit is seen, and we present our investigations into the sources of this excess. Compared with the results of previous such experiments, the phase sensitivity over the full 100-Hz-10-kHz band of interest has been improved by factors of up to 100, with a factor-of-2.5 improvement in the quantum-limited level.
Interferometric detection of gravitational waves at levels of astrophysical interest is expected to require measurement of optical phase differences of $\ensuremath{\le}{10}^{\ensuremath{-}10}$ rad. To achieve this sensitivity the measurement must be made at the quantum (shot noise) limit. We have built a laboratory-scale interferometer to investigate limits to sensing the phase at this level, and obtained, with 70 W of circulating power, a phase sensitivity limited by shot noise of $3\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}10}\phantom{\rule{0ex}{0ex}}\mathrm{rad}/\sqrt{\mathrm{Hz}}$ at frequencies above 1.5 kHz. We describe the experiment and discuss the implications for the Laser Interferometer Gravitational-Wave Observatory (LIGO).
The LIGO project (Laser Interferometer Gravitational-Wave Observatory) is currently engaged in the construction of a new observatory to measure gravitational radiation from astrophysical sources. The first generation of interferometric gravitational wave antennas is scheduled to come on-line in 2001. With an initial noise level of ... at frequencies around 200Hz, these antennas represent the most sensitive instruments ever constructed for the detection of gravitational radiation, To achieve the required sensitivity, the antennas are configured as recycled Michelson Interferometers with Fabry-Perot cavities in the Michelson arms. One of the fundamental limits associated with an instrument of this type is the ability to detect differential phase shifts between the beams returning to the beamsplitter from the Fabry-Perot arm cavities. To achieve the planned sensitivity to gravitational radiation, this detection should be limited only by photon courting statistics ("shot noise") at a level of ... between 150Hz and 10kHT. The goal of this work is to develop and demonstrate the techniques which are necessary to achieve this optical phase sensitivity. A prototype recycled Michelson interferometer was constructed which reached an optical phase sensitivity of ... above 600 Hz. This thesis describes the methods used to achieve this optical phase sensitivity, and details the lessons learned from operating the prototype instrument. We pay particular attention to interferometric control of suspended optics, laser frequency control, and thermal lensing.
The ability to directly detect gravitational waves will open a completely new branch of astronomy to view the Universe, one that is inaccessible to electromagnetic-based astronomy. First generation ground-based interferometric gravitational-wave detectors have achieved strain sensitivities of order one part in ten to the twenty-one, at 100 Hz detection frequency. A new generation of detectors are under construction, designed to improve on the sensitivity of the first-generation detectors by a factor of 10. The quantum nature of light will broadly limit the sensitivity of these new instruments. This quantum noise will originate from the quantum vacuum fluctuations that enter the unused port of the interferometer. One of the most promising options for reducing the quantum noise impact and further increasing the sensitivity is applying quantum squeezed vacuum states. These squeezed states have lower noise in one quadrature than the vacuum state. By replacing the quantum vacuum fluctuations entering the interferometer with squeezed vacuum states, the quantum noise impact is reduced. This thesis firstly details the development of a squeezed light source that produces squeezed states applicable for enhancing interferometric gravitational-wave detectors. A doubly-resonant, travelling-wave bow-tie cavity squeezed light source is presented. For the first time, greater than 10 dB of quantum noise suppression across the gravitational-wave detection band is directly observed, and 11.6 dB of quantum noise suppression is observed above 200 Hz. This squeezing cavity design also has benefits with intrinsic isolation to backscattered light. Experiments that quantify this isolation are reported. The properties affecting squeezing magnitude and low-frequency squeezing measurement are discussed. In addition, a modified squeezing-ellipse-phase control technique for squeezed vacuum states is presented. This thesis secondly presents results from the LIGO Squeezed Light Injection Experiment, undertaken to test squeezed light injection into a 4 km interferometric gravitational-wave detector. The results of the experiment show the first measurement of squeezing-enhancement in a 4 km gravitational-wave detector, with 2.15 dB measured above 250 Hz. This represents the best sensitivity to gravitational waves yet achieved at these frequencies by any single gravitational-wave detector to date. An unknown area was whether the addition of a squeezer would introduce noise couplings that degrade the crucial low frequency sensitivity. The results demonstrate that injected squeezed states are compatible with low frequency gravitational-wave measurement. The characterisation of squeezing-injection optical losses and fluctuations of the squeezing angle are also reported. The knowledge and processes gained, from both the squeezed light source development work and the LIGO Squeezed Light Injection Experiment, will inform the design, planning and implementation of squeezed states in future gravitational-wave detectors.
Quantum mechanics and general relativity are the foundational pillars of modern physics, yet experimental tests that combine the two frameworks remain rare. Measuring optical phase shifts of massless photons in a gravitational potential provides a unique quantum platform to probe gravity beyond Newtonian descriptions, but laboratory-based interferometers have not yet reached the sensitivity needed to access this regime. Here, we report the realization of a 50-km table-top Mach-Zehnder fiber interferometer operating at the single-photon level, achieving a phase sensitivity of 4.42×10−64.42\times10^{-6}4.42×10−6 rad root-mean-square (RMS) within the frequency range of 0.01 Hz to 5 Hz. We demonstrate that this sensitivity is sufficient to resolve a phase-shift signal of (6.18±0.44)×10−5(6.18 \pm 0.44)\times10^{-5}(6.18±0.44)×10−5 rad RMS at 0.1 Hz, associated with a modulated gravity-induced signal. Our results establish a milestone for quantum sensing with large-scale optical interferometry, demonstrating the capability to detect gravitational redshifts in a local laboratory, thereby paving the way for testing quantum phenomena within general relativistic frameworks.
Interferometric gravitational wave detectors (such as advanced LIGO) employ high-power solid-state lasers to maximize their detection sensitivity and hence their reach into the universe. These sophisticated light sources are ultra-stabilized with regard to output power, emission frequency and beam geometry; this is crucial to obtain low detector noise. However, even when all laser noise is reduced as far as technically possible, unavoidable quantum noise of the laser still remains. This is a consequence of the Heisenberg Uncertainty Principle, the basis of quantum mechanics: in this case, it is fundamentally impossible to simultaneously reduce both the phase noise and the amplitude noise of a laser to arbitrarily low levels. This fact manifests in the detector noise budget as two distinct noise sources—photon shot noise and quantum radiation pressure noise—which together form a lower boundary for current-day gravitational wave detector sensitivities, the standard quantum limit of interferometry. To overcome this limit, various techniques are being proposed, among them different uses of non-classical light and alternative interferometer topologies. This article explains how quantum noise enters and manifests in an interferometric gravitational wave detector, and gives an overview of some of the schemes proposed to overcome this seemingly fundamental limitation, all aimed at the goal of higher gravitational wave event detection rates. This article is part of a discussion meeting issue ‘The promises of gravitational-wave astronomy’.
Gravitational waves manifest as a time varying straining of space: they arise from the accelerating motions of large bodies of mass and propagate across the universe at the speed of light as ripples in the fabric of space-time, a fleetingly weak effect so far eluding direct detection. The detection of gravitation waves is expected to yield a rich vein to observational astronomy, complementing existing electromagnetic surveys and revealing a hitherto unexplored range of phenomena. First generation interferometric gravitational wave detectors, notably Enhanced LIGO, achieved strain sensitivities of one part in ten to power twenty-one per square-root-Hertz at 100 Hz with an expected detection rate of 2-3 events per year. Commissioning of a new generation of Advanced LIGO interferometric detectors has concluded recently with a resultant ten-fold sensitivity improvement. Overall their potential event detection space has increased by a factor of 1000. The quantum nature of light within these detectors now limits their sensitivity over most of their frequency range. This quantum noise limit is driven by the vacuum quadrature fluctuations propagated through their open detection ports and represents a fundamental noise floor to their strain sensitivity. This thesis addresses two distinct approaches to quantum noise improvement for future upgrades to advanced detectors. The first addresses the issue of quantum noise by adopting a quantum non-demolition approach to detector readout variables, the so-called `speed-meter’ design. Such a modified instrument samples test mass momentum, a quantity for which time separated measurements commute and are therefore not bound by Heisenberg-like limits. A novel polarisation-folded sloshing cavity type speed-meter is proposed where readout fields are stored and delayed in the orthogonal polarisation of the interferometer’s arms cavities. Here frequency dependence is selected to cancel position like measurements so that only test mass momentum information remains. A quantum noise propagation model is developed and a sensitivity performance is demonstrated that beats the standard quantum limit below 100 Hz over a broad range of frequencies. A second approach to achieve quantum noise enhancement in advanced detectors involves injection of quadrature-squeezed states in the place of vacuum. This dissertation details the development of a prototype squeezed vacuum source suitable to the demanding enhancement requirements for an Advanced LIGO squeezing installation. The construction of a doubly resonant, bow-tie cavity source is presented. This employs a novel monolithic all-glass cavity construction and is vacuum compatible. This design demonstrates the viability of building a cavity using optical contacting as a construction technique for attaching mounting prisms to highly polished fused-silica breadboards. Such a design can be expected to have excellent length noise stability, provide low intrinsic phase noise and would be suitable to mount on seismic isolation stages within the LIGO vacuum envelope. Further, the travelling wave cavity design should provide excellent 50 dB intrinsic backscatter isolation. We demonstrate the first operation of such a complex non-linear device under vacuum, producing 8.6 dB of measured vacuum squeezing down to 10 Hz across the advanced LIGO ‘audio-band’ detection range.