Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IET Communications

Performance improvement of short-length regular low-density parity-check codes with low-complexity post-processing

Raghunadh K. Bhattar, K.R. Ramakrishnan, K. S. Dasgupta

Published Oct 16, 2012• 1 citation
Publisher

Abstract

It is well known that extremely long low-density parity-check (LDPC) codes perform exceptionally well for error correction applications, short-length codes are preferable in practical applications. However, short-length LDPC codes suffer from performance degradation owing to graph-based impairments such as short cycles, trapping sets and stopping sets and so on in the bipartite graph of the LDPC matrix. In particular, performance degradation at moderate to high Eb/N0 is caused by the oscillations in bit node a posteriori probabilities induced by short cycles and trapping sets in bipartite graphs. In this study, a computationally efficient algorithm is proposed to improve the performance of short-length LDPC codes at moderate to high Eb/N0. This algorithm makes use of the information generated by the belief propagation (BP) algorithm in previous iterations before a decoding failure occurs. Using this information, a reliability-based estimation is performed on each bit node to supplement the BP algorithm. The proposed algorithm gives an appreciable coding gain as compared with BP decoding for LDPC codes of a code rate equal to or less than 1/2 rate coding. The coding gains are modest to significant in the case of optimised (for bipartite graph conditioning) regular LDPC codes, whereas the coding gains are huge in the case of unoptimised codes. Hence, this algorithm is useful for relaxing some stringent constraints on the graphical structure of the LDPC code and for developing hardware-friendly designs.

DOI
10.1049/iet-com.2011.0292

Related papers

Short-length Low-density Parity-check Codes: Construction and Decoding Algorithms

Cornelius T. Healy

Error control coding is an essential part of modern communications systems. LDPC codes have been demonstrated to offer performance near the fundamental limits of channels corrupted by random noise. Optimal maximum likelihood decoding of LDPC codes is too complex to be practically useful even at short block lengths and so a graph-based message passing decoder known as the belief propagation algorithm is used instead. In fact, on graphs without closed paths known as cycles the iterative message passing decoding is known to be optimal and may converge in a single iteration, although identifying the message update schedule which allows single-iteration convergence is not trivial. At finite block lengths graphs without cycles have poor minimum distance properties and perform poorly even under optimal decoding. LDPC codes with large block length have been demonstrated to offer performance close to that predicted for codes of infinite length, as the cycles present in the graph are quite long. In this thesis, LDPC codes of shorter length are considered as they offer advantages in terms of latency and complexity, at the cost of performance degradation from the increased number of short cycles in the graph. For these shorter LDPC codes, the problems considered are: \n \nFirst, improved construction of structured and unstructured LDPC code graphs of short length with a view to reducing the harmful effects of the cycles on error rate performance, based on knowledge of the decoding process. Structured code graphs are particularly interesting as they allow benefits in encoding and decoding complexity and speed. Secondly, the design and construction of LDPC codes for the block fading channel, a particularly challenging scenario from the point of view of error control code design. Both established and novel classes of codes for the channel are considered. Finally the decoding of LDPC codes by the belief propagation algorithm is considered, in particular the scheduling of messages passed in the iterative decoder. A knowledge-aided approach is developed based on message reliabilities and residuals to allow fast convergence and significant improvements in error rate performance.

•Jul 1, 2014•4 citations

A high‐performance belief propagation decoding algorithm for codes with short cycles

Ali Karimi-lenji, Monireh Houshmand, Fahimeh Zarmehi

Summary The simplicity of decoding is one of the most important characteristics of the low density parity check (LDPC) codes. Belief propagation (BP) decoding algorithm is a well‐known decoding algorithm for LDPC codes. Most LDPC codes with long lengths have short cycles in their Tanner graphs, which reduce the performance of the BP algorithm. In this paper, we present 2 methods to improve the BP decoding algorithm for LDPC codes. In these methods, the calculation of the variable nodes is controlled by using “multiplicative correction factor” and “additive correction factor.” These factors are obtained for 2 separate channels, namely additive white Gaussian noise (AWGN) and binary symmetric channel (BSC), as 2 functions of code and channel parameters. Moreover, we use the BP‐based method in the calculation of the check nodes, which reduces the required resources. Simulation results show the proposed algorithm has better performance and lower decoding error as compared to BP and similar methods like normalized‐BP and offset‐BP algorithms.

International Journal of Communication Systems•Feb 28, 2017•2 citations

Modified Belief Propagation Decoding Algorithm for Low-Density Parity Check Code Based on Oscillation

Satoshi Gounai, Tomoaki Otsuki Ohtsuki, T. Kaneko

A low-density parity check (LDPC) code with the belief propagation (BP) or the log-likelihood ratio belief propagation (LLR-BP) can achieve good bit error rate (BER) performance approaching the Shannon limit. When a parity check matrix of the LDPC code has the cycle, the BP and LLR-BP decoding algorithms achieve approximate maximum a posterior probability (MAP) decoding. Although the decoding algorithms are approximate MAP decoding, LDPC codes can achieve very good BER. For the short and middle length LDPC codes, BER and block error rate (BLER) performances are affected by cycle largely. In each iteration, the magnitudes of a posterior LLRs of some bits oscillate owing to cycles. The oscillation is the dominant error factor in the high Eb/Noregion for short and middle length LDPC codes. In this paper, we extend the definition of oscillation to extrinsic LLR (ex-LLR) derived in the bit node process and propose the modified LLR-BP and the modified UMP-BP decoding algorithms. To reduce effects of oscillating ex-LLRs on decoding, for oscillating ex-LLRs, we add the previous ex-LLR to the current ex-LLR. From the computer simulation, we show that for short and middle length LDPC codes, with a simple modification, our proposed decoding algorithms can improve the conventional LLR-BP and UMP-BP decoding algorithms. In particular, we show that the modified UMP-BP decoding algorithm with low complexity can achieve better BER and BLER than the conventional LLR-BP decoding algorithm

IEEE Vehicular Technology Conference•Sep 8, 2006•16 citations

Improved Belief Propagation (BP) Decoding for LDPC Codes with a large number of short cycles

Kyuhyuk Chung, Jun Heo

In this paper, we improve performance of Low Density Parity Check (LDPC) codes by adding a large number of short cycles. Short cycles, especially cycles of length 4, degrade performance of LDPC codes if the standard BP (Belief Propagation) decoding is used. Therefore current researches have focused on removing cycles of length 4 for designing good performance LDPC codes. We found that a large number of cycles of length 4 improve performance of LDPC codes if a modified BP decoding is used. We present the modified BP decoding algorithm for LDPC codes with a large number of short cycles. We show that the modified BP decoding performance of LDPC codes with a large number of short cycles is better than the standard BP decoding performance of LDPC codes designed by avoiding short cycles.

IEEE Vehicular Technology Conference•Sep 8, 2006•16 citations

Reduced complexity and improved performance decoding algorithm for nonbinary LDPC codes over GF(q)

Xin Chen, Aidong Men

Low-density parity-check (LDPC) codes over finite fields GF(q) have a better performance than those of the binary low-density parity-check codes, at short and medium block lengths, but the decoder of GF(q)-LDPC has more complexity. In this paper, we present a new reduced-complexity belief propagation (BP) decoding algorithm for GF(q)-LDPC codes by analyzing the reliability of code symbols. Instead of update all the variable nodes during iteration, we just update variable nodes which are mostly to be in an error. The algorithm also shows a property to reduce the effects of oscillating on decoding. The simulations prove that we could improve performance and reduce complexity at the same time for short and medium GF(q)-LDPC codes.

IEEE International Conference on Communication Technology (ICCT)•Nov 1, 2008•6 citations

Techniques for the decoding of low density parity check codes: efficient simulation, algorithm improvement and implementation

Babak Daneshrad, Enver Çavuş

After the introduction of iterative coding, Low Density Parity Check (LDPC) codes have received a lot of attention due to their remarkable near Shannon-limit performance and practical decoder implementation. However, when employing an LDPC code for various applications, multiple issues do arise at the simulation, algorithm and implementation levels. The first issue is the performance evaluation of the iterative LDPC decoder in the very low Bit Error Rate (BER) regions. So far, no analytical tool has been developed to evaluate the performance of LDPC codes. Unfortunately standard Monte Carlo (MC) simulations cannot be used for performance estimation in these low BER regions due to prohibitive execution times. The second issue is the efficiency of the decoding algorithm. Due to the presence of short cycles in the bipartite graph, sum-product decoding algorithms lead to considerable performance loss for short block-length LDPC codes and produce error floors for longer codes. In addition, the iterative processing and estimation of soft probabilistic values with these algorithms result in very high computational complexity, which in turn impedes the adoption of LDPC codes for power constrained systems. Another prime objective is to design a high throughput decoder architecture which is capable of supporting multiple rates and variable code lengths within minimal area. This work aims to address and provide solutions to the above problems. As a solution to the performance estimation problem of LDPC codes, a highly efficient and novel fast BER simulation technique is developed. At the algorithm level, a performance improvement and error floor avoidance method is introduced, and a computationally efficient algorithm is developed for the sum-product decoding of LDPC codes. And finally, at the architecture level, a high throughput multi-rate variable code length implementation is presented which, when implemented, efficiently minimizes device resources while alleviating the routing complexity of the decoder.

•Jan 1, 2007•2 citations
It is well known that extremely long low-density parity-check (LDPC) codes perform exceptionally well for error correction applications, short-length codes are preferable in practical applications. However, short-length LDPC codes suffer from performance degradation owing to graph-based impairments such as short cycles, trapping sets and stopping sets and so on in the bipartite graph of the LDPC matrix. In particular, performance degradation at moderate to high Eb/N0 is caused by the oscillations in bit node a posteriori probabilities induced by short cycles and trapping sets in bipartite graphs. In this study, a computationally efficient algorithm is proposed to improve the performance of short-length LDPC codes at moderate to high Eb/N0. This algorithm makes use of the information generated by the belief propagation (BP) algorithm in previous iterations before a decoding failure occurs. Using this information, a reliability-based estimation is performed on each bit node to supplement the BP algorithm. The proposed algorithm gives an appreciable coding gain as compared with BP decoding for LDPC codes of a code rate equal to or less than 1/2 rate coding. The coding gains are modest to significant in the case of optimised (for bipartite graph conditioning) regular LDPC codes, whereas the coding gains are huge in the case of unoptimised codes. Hence, this algorithm is useful for relaxing some stringent constraints on the graphical structure of the LDPC code and for developing hardware-friendly designs.
Error control coding is an essential part of modern communications systems. LDPC codes have been demonstrated to offer performance near the fundamental limits of channels corrupted by random noise. Optimal maximum likelihood decoding of LDPC codes is too complex to be practically useful even at short block lengths and so a graph-based message passing decoder known as the belief propagation algorithm is used instead. In fact, on graphs without closed paths known as cycles the iterative message passing decoding is known to be optimal and may converge in a single iteration, although identifying the message update schedule which allows single-iteration convergence is not trivial. At finite block lengths graphs without cycles have poor minimum distance properties and perform poorly even under optimal decoding. LDPC codes with large block length have been demonstrated to offer performance close to that predicted for codes of infinite length, as the cycles present in the graph are quite long. In this thesis, LDPC codes of shorter length are considered as they offer advantages in terms of latency and complexity, at the cost of performance degradation from the increased number of short cycles in the graph. For these shorter LDPC codes, the problems considered are: \n \nFirst, improved construction of structured and unstructured LDPC code graphs of short length with a view to reducing the harmful effects of the cycles on error rate performance, based on knowledge of the decoding process. Structured code graphs are particularly interesting as they allow benefits in encoding and decoding complexity and speed. Secondly, the design and construction of LDPC codes for the block fading channel, a particularly challenging scenario from the point of view of error control code design. Both established and novel classes of codes for the channel are considered. Finally the decoding of LDPC codes by the belief propagation algorithm is considered, in particular the scheduling of messages passed in the iterative decoder. A knowledge-aided approach is developed based on message reliabilities and residuals to allow fast convergence and significant improvements in error rate performance.
Summary The simplicity of decoding is one of the most important characteristics of the low density parity check (LDPC) codes. Belief propagation (BP) decoding algorithm is a well‐known decoding algorithm for LDPC codes. Most LDPC codes with long lengths have short cycles in their Tanner graphs, which reduce the performance of the BP algorithm. In this paper, we present 2 methods to improve the BP decoding algorithm for LDPC codes. In these methods, the calculation of the variable nodes is controlled by using “multiplicative correction factor” and “additive correction factor.” These factors are obtained for 2 separate channels, namely additive white Gaussian noise (AWGN) and binary symmetric channel (BSC), as 2 functions of code and channel parameters. Moreover, we use the BP‐based method in the calculation of the check nodes, which reduces the required resources. Simulation results show the proposed algorithm has better performance and lower decoding error as compared to BP and similar methods like normalized‐BP and offset‐BP algorithms.
A low-density parity check (LDPC) code with the belief propagation (BP) or the log-likelihood ratio belief propagation (LLR-BP) can achieve good bit error rate (BER) performance approaching the Shannon limit. When a parity check matrix of the LDPC code has the cycle, the BP and LLR-BP decoding algorithms achieve approximate maximum a posterior probability (MAP) decoding. Although the decoding algorithms are approximate MAP decoding, LDPC codes can achieve very good BER. For the short and middle length LDPC codes, BER and block error rate (BLER) performances are affected by cycle largely. In each iteration, the magnitudes of a posterior LLRs of some bits oscillate owing to cycles. The oscillation is the dominant error factor in the high Eb/Noregion for short and middle length LDPC codes. In this paper, we extend the definition of oscillation to extrinsic LLR (ex-LLR) derived in the bit node process and propose the modified LLR-BP and the modified UMP-BP decoding algorithms. To reduce effects of oscillating ex-LLRs on decoding, for oscillating ex-LLRs, we add the previous ex-LLR to the current ex-LLR. From the computer simulation, we show that for short and middle length LDPC codes, with a simple modification, our proposed decoding algorithms can improve the conventional LLR-BP and UMP-BP decoding algorithms. In particular, we show that the modified UMP-BP decoding algorithm with low complexity can achieve better BER and BLER than the conventional LLR-BP decoding algorithm
In this paper, we improve performance of Low Density Parity Check (LDPC) codes by adding a large number of short cycles. Short cycles, especially cycles of length 4, degrade performance of LDPC codes if the standard BP (Belief Propagation) decoding is used. Therefore current researches have focused on removing cycles of length 4 for designing good performance LDPC codes. We found that a large number of cycles of length 4 improve performance of LDPC codes if a modified BP decoding is used. We present the modified BP decoding algorithm for LDPC codes with a large number of short cycles. We show that the modified BP decoding performance of LDPC codes with a large number of short cycles is better than the standard BP decoding performance of LDPC codes designed by avoiding short cycles.
Low-density parity-check (LDPC) codes over finite fields GF(q) have a better performance than those of the binary low-density parity-check codes, at short and medium block lengths, but the decoder of GF(q)-LDPC has more complexity. In this paper, we present a new reduced-complexity belief propagation (BP) decoding algorithm for GF(q)-LDPC codes by analyzing the reliability of code symbols. Instead of update all the variable nodes during iteration, we just update variable nodes which are mostly to be in an error. The algorithm also shows a property to reduce the effects of oscillating on decoding. The simulations prove that we could improve performance and reduce complexity at the same time for short and medium GF(q)-LDPC codes.
After the introduction of iterative coding, Low Density Parity Check (LDPC) codes have received a lot of attention due to their remarkable near Shannon-limit performance and practical decoder implementation. However, when employing an LDPC code for various applications, multiple issues do arise at the simulation, algorithm and implementation levels. The first issue is the performance evaluation of the iterative LDPC decoder in the very low Bit Error Rate (BER) regions. So far, no analytical tool has been developed to evaluate the performance of LDPC codes. Unfortunately standard Monte Carlo (MC) simulations cannot be used for performance estimation in these low BER regions due to prohibitive execution times. The second issue is the efficiency of the decoding algorithm. Due to the presence of short cycles in the bipartite graph, sum-product decoding algorithms lead to considerable performance loss for short block-length LDPC codes and produce error floors for longer codes. In addition, the iterative processing and estimation of soft probabilistic values with these algorithms result in very high computational complexity, which in turn impedes the adoption of LDPC codes for power constrained systems. Another prime objective is to design a high throughput decoder architecture which is capable of supporting multiple rates and variable code lengths within minimal area. This work aims to address and provide solutions to the above problems. As a solution to the performance estimation problem of LDPC codes, a highly efficient and novel fast BER simulation technique is developed. At the algorithm level, a performance improvement and error floor avoidance method is introduced, and a computationally efficient algorithm is developed for the sum-product decoding of LDPC codes. And finally, at the architecture level, a high throughput multi-rate variable code length implementation is presented which, when implemented, efficiently minimizes device resources while alleviating the routing complexity of the decoder.