Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physica C Superconductivity

Influence of parasitic capacitance on the oxide SFQ circuit operation

Y. Tarutani, Koji Tsubone, H. Wakana, Seiji Adachi, Yoshihiro Ishimaru, Yasuo Oshikubo, Osami Horibe, K. Tanabe

Published Jun 4, 2007• 3 citations
Publisher
DOI
10.1016/j.physc.2007.02.054

Related papers

Toggle-flip-flop operation in oxide SFQ circuit

Koji Tsubone, Y. Tarutani, H. Wakana +7 more

Physica C Superconductivity•Jul 8, 2006•4 citations

New type of SFQ-dc converter for use in oxide circuits

Y. Tarutani, Yoshihiro Ishimaru, H. Wakana +6 more

Physica C Superconductivity•Jun 3, 2004•13 citations

Fabrication and characteristics of SFQ circuit elements made of oxide thin films

Y. Tarutani, Yoshihiro Ishimaru, H. Wakana +7 more

Physica C Superconductivity•Aug 9, 2005•2 citations

Analysis of Interference for Low-Voltage-Driven SFQ Circuits

Takumi Takinami, Ito Masato, Kitayama Atsushi +2 more

IEICE Technical Report; IEICE Tech. Rep.•Jan 17, 2013•0 citations

Performance of DC SQUIDs with parasitic elements

J Schambach, L Warzemann, Peter B. Weber +5 more

The influence on the I-V curves and on the noise properties of parasitic capacitances caused by a covered slit of a Ketchen-type SQUID has been studied. The experimental results are compared with numerical simulations based on a lumped-circuit-element model. In the I-V characteristics we found two operating points, with minimum white noise, that were independent of the parasitic capacitance.

Superconductor Science and Technology•May 1, 1994•3 citations

Impedance Matching of Microstrip Inductors in Digital Superconductive Electronics

Thomas Ortlepp, Friedrich Uhlmann

State-of-the-art RSFQ circuits consist of Josephson junctions, inductances and bias current sources, where the inductances are practically used as functional elements. Even more, their value defines the functionality and therefore the conventional design process requires strict conditions for the wiring between Josephson junctions. The present design and optimization process does not take into account their parasitic capacitances to ground. This becomes an important issue for ultra fast applications above 100 GHz, but also for circuits dedicated to control quantum electronics. We report on a theoretical and experimental investigation of the influence of ground capacitances. The impedance matching between the connecting microstrip lines and the Josephson junction is a key issue for the correct operation of these circuits. We performed circuit simulations and collected experimental data of correct and incorrect operating circuits to derive design criteria. The critical reflection coefficient is found to be 0.35 and the particular design must use a smaller value for transfer and a larger value for storage of SFQ pulses, respectively.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•12 citations
State-of-the-art RSFQ circuits consist of Josephson junctions, inductances and bias current sources, where the inductances are practically used as functional elements. Even more, their value defines the functionality and therefore the conventional design process requires strict conditions for the wiring between Josephson junctions. The present design and optimization process does not take into account their parasitic capacitances to ground. This becomes an important issue for ultra fast applications above 100 GHz, but also for circuits dedicated to control quantum electronics. We report on a theoretical and experimental investigation of the influence of ground capacitances. The impedance matching between the connecting microstrip lines and the Josephson junction is a key issue for the correct operation of these circuits. We performed circuit simulations and collected experimental data of correct and incorrect operating circuits to derive design criteria. The critical reflection coefficient is found to be 0.35 and the particular design must use a smaller value for transfer and a larger value for storage of SFQ pulses, respectively.