Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optical Amplifiers and Their Applications

Polarization hole-burning in erbium-doped fiber amplifiers with birefringence

Paul F. Wysocki

Published Jan 1, 1994• 7 citations
Publisher

Abstract

In Er-doped fiber amplifiers (EDFA), ASE polarized orthogonal to a saturating signal experiences more gain than ASE with the same polarization as the saturating signal.1 The accumulated enhancement of orthogonal ASE degrades the performance of long systems.1,2 This effect has been observed in single EDFAs using differential measurement techniques.3,4 A computer model of polarization hole-burning (PHB) has been presented.5 It postulates that each ion has an ellipsoid-like surface representing the emission and absorption cross-sections. The ratio of the major to minor cross-sections is the anisotropy parameter:

DOI
10.1364/oaa.1994.thb4

Related papers

Observation of polarization hole burning in Er-doped fiber for circular polarization of the saturating signal

V.J. Mazurczyk, Rogers H. Stolen, Jau-Sheng Wang +1 more

Polarization hole burning (PHB) has been observed in individual erbium-doped amplifiers.1 PHB means that a polarized saturating signal causes anisotropic saturation in an erbium- doped fiber (EDF). The resulting gain measured with a weak probe is maximum when the probe state of polarization (SOP) is orthogonal to the signal SOP and is minimum for the same SOP. The absorption is also anisotropic and is the compliment of the gain; i.e., where the gain is maximum the absorption is minimum and vice versa. The saturation anisotropy is characterized by the difference (in dB) between extrema for gain δG or the absorption δA. If the same order of subtraction is maintained, δG is positive and δA is negative.

Optical Fiber Communication Conference•Jan 1, 1995•8 citations

THE EFFECT of BIREFRINGENCE on POLARIZATION HOLE BURNING in ERBIUM DOPED FIBER AMPLIFIERS.

V.J. Mazurczyk, CRAIG D. POOLE

Polarization hole burning, PHB, has been observed in erbium doped fiber amplifiers[1]. PHB is an anisotropic saturation created when a polarized saturating signal is launched into the erbium doped fiber. A corresponding anisotropic gain is also created. The gain, measured with a weak probe, is found to be larger for a probe polarized orthogonal to the saturating signal compared to a probe polarized parallel to the saturating signal. The effect is typically expressed as the gain difference, δG, (in dB) for the two probe polarizations.

Optical Amplifiers and Their Applications•Jan 1, 1994•9 citations

On polarization of the fluorescence in erbium-doped fibers

Liliana O. Martínez-Martínez, E. Hernández-Hernández, Serguei I. Stepanov

"Theoretical evaluations of polarization degree of the fluorescence excited in erbium doped fibers (EDF) dependence on the excitation light power are presented. In calculations we use the model of randomly oriented and not interacting Er3+ ions. Assumption of the reduced optical anisotropy of the individual ions (with the absorption/emission cross-sections described with the ellipsoids) is shown to be necessary to get a reasonable agreement with the existing experimental data. Similar values of the anisotropy parameters (0.6-0.7) are also utilized to explain the experimental data on polarization hole burning in EDF earlier."

Revista Mexicana de Física•Jan 1, 2013•2 citations

Polarization-dependent gain in erbium-doped fibers

R. W. Keys, S.J. Wilson, M. Healy +3 more

One component of polarization-dependent gain (PDG) in optical amplifiers has been shown to originate from polarization hole burning (PHB) in the erbium fibers.1 In this paper we quantify its magnitude for copumped amplifiers under operating conditions typical of those used in long-haul amplified systems. We find that PDG can be significant, even when the polarization state of the signal is circular, and that hole burning due to the polarization of the 1480-nm pump laser contributes significantly to the overall polarization-dependent gain of the fiber.

Optical Fiber Communication Conference•Jan 1, 1994•8 citations

Polarization dependent gain in erbium doped-fiber amplifiers

V.J. Mazurczyk, J.L. Zyskind

Measurement of polarization hole burning is reported for an erbium doped fiber amplifier. This effect produces a dependence of gain, measured with a weak probe, on the polarization of the saturating signal; the maximum gain occurs for probe polarizations orthogonal to the signal. The pump also contributes to the gain dependence on polarization. Reduction of the degree of polarization of both pump and signal below 10% reduces the polarization dependent gain substantially.>

IEEE Photonics Technology Letters•May 1, 1994•103 citations

Observation of Replica Holes in Erbium Doped Silica Fiber

Thiago P. Mayer Alegre, Gustavo S. Wiederhecker, Hugo L. Fragnito

Abstract We observed for the first time to our knowledge the presence of replica holes in the fluorescencespectrum of EDFA. Saturating the Er 3+ transition at a single wavelength we noticed theappearance of spectral holes in the ASE other than the usual one around the saturating laser. Wequalitatively explain the effect and confront the experimental results with the homogeneouslybroadened model. Introduction One of the limiting factors to state-of-the-art DWDM systems is the effect of Spectral Hole Burning (SHB) inErbium Doped Fiber Amplifiers (EDFAs). It has been already observed that the presence of a saturating signal ina given wavelength induces a hole around the signal in the gain and Amplified Spontaneous Emission (ASE)spectra [1],[2]. These holes in EDFAs are typically between 2 and 8 nm width, which is enough to degrade theneighboring channels. The SHB effect is due to the inhomogeneous broadening of the Er 3+ transitions, causedby site-to-site variations of the local electric field in the silica based host, which induces different ions laser linesproperties.This work shows the existence of spectral holes burned at wavelengths far from the saturating laserline, called Spectral Replica Holes (SRHs). The physical background that explains SRHs is based on theinhomogeneously broadened two-level Stark Splitted

•Jan 1, 2003•1 citation
In Er-doped fiber amplifiers (EDFA), ASE polarized orthogonal to a saturating signal experiences more gain than ASE with the same polarization as the saturating signal.1 The accumulated enhancement of orthogonal ASE degrades the performance of long systems.1,2 This effect has been observed in single EDFAs using differential measurement techniques.3,4 A computer model of polarization hole-burning (PHB) has been presented.5 It postulates that each ion has an ellipsoid-like surface representing the emission and absorption cross-sections. The ratio of the major to minor cross-sections is the anisotropy parameter:
Polarization hole burning (PHB) has been observed in individual erbium-doped amplifiers.1 PHB means that a polarized saturating signal causes anisotropic saturation in an erbium- doped fiber (EDF). The resulting gain measured with a weak probe is maximum when the probe state of polarization (SOP) is orthogonal to the signal SOP and is minimum for the same SOP. The absorption is also anisotropic and is the compliment of the gain; i.e., where the gain is maximum the absorption is minimum and vice versa. The saturation anisotropy is characterized by the difference (in dB) between extrema for gain δG or the absorption δA. If the same order of subtraction is maintained, δG is positive and δA is negative.
Polarization hole burning, PHB, has been observed in erbium doped fiber amplifiers[1]. PHB is an anisotropic saturation created when a polarized saturating signal is launched into the erbium doped fiber. A corresponding anisotropic gain is also created. The gain, measured with a weak probe, is found to be larger for a probe polarized orthogonal to the saturating signal compared to a probe polarized parallel to the saturating signal. The effect is typically expressed as the gain difference, δG, (in dB) for the two probe polarizations.
"Theoretical evaluations of polarization degree of the fluorescence excited in erbium doped fibers (EDF) dependence on the excitation light power are presented. In calculations we use the model of randomly oriented and not interacting Er3+ ions. Assumption of the reduced optical anisotropy of the individual ions (with the absorption/emission cross-sections described with the ellipsoids) is shown to be necessary to get a reasonable agreement with the existing experimental data. Similar values of the anisotropy parameters (0.6-0.7) are also utilized to explain the experimental data on polarization hole burning in EDF earlier."
One component of polarization-dependent gain (PDG) in optical amplifiers has been shown to originate from polarization hole burning (PHB) in the erbium fibers.1 In this paper we quantify its magnitude for copumped amplifiers under operating conditions typical of those used in long-haul amplified systems. We find that PDG can be significant, even when the polarization state of the signal is circular, and that hole burning due to the polarization of the 1480-nm pump laser contributes significantly to the overall polarization-dependent gain of the fiber.
Abstract We observed for the first time to our knowledge the presence of replica holes in the fluorescencespectrum of EDFA. Saturating the Er 3+ transition at a single wavelength we noticed theappearance of spectral holes in the ASE other than the usual one around the saturating laser. Wequalitatively explain the effect and confront the experimental results with the homogeneouslybroadened model. Introduction One of the limiting factors to state-of-the-art DWDM systems is the effect of Spectral Hole Burning (SHB) inErbium Doped Fiber Amplifiers (EDFAs). It has been already observed that the presence of a saturating signal ina given wavelength induces a hole around the signal in the gain and Amplified Spontaneous Emission (ASE)spectra [1],[2]. These holes in EDFAs are typically between 2 and 8 nm width, which is enough to degrade theneighboring channels. The SHB effect is due to the inhomogeneous broadening of the Er 3+ transitions, causedby site-to-site variations of the local electric field in the silica based host, which induces different ions laser linesproperties.This work shows the existence of spectral holes burned at wavelengths far from the saturating laserline, called Spectral Replica Holes (SRHs). The physical background that explains SRHs is based on theinhomogeneously broadened two-level Stark Splitted