Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Hyperpolarised helium and xenon production and applications to imaging and materials analysis

Cavin Talbot

Published Aug 1, 2008• 0 citations
Publisher

Abstract

In this thesis I discuss experiments to create hyperpolarised noble gases. In particular, we have constructed an apparatus to hyperpolarise helium and xenon gases and used these resources to image the lungs of living rats and probe the physical properties of mesoporous solids. The apparatus uses a line-width narrowed laser diode array to optically pump rubidium vapour which then polarises the noble gases through spin-exchange collisions. We have also developed techniques to optimise both the amount and rate of polarisation. Using these techniques, we have shown that the apparatus can produce hyperpolarised helium in 350mL volumes with a polarisation of up to 25%. It can also produce hyperpolarised xenon in a continuous flow which results in 10% polarisation of the xenon at a rate of 1018 polarised atoms per minute with only four watts of laser light incident on the cell. The optical feedback system for laser diode arrays was improved to correct for the divergence of the beam caused by curvature in the array of diode elements. This curvature of the array is an artifact of the manufacturing process and causes an increase in the full width half maximum (FWHM) achievable for the spectral profile of the array when using optical feedback to spectrally narrow the laser diode array. The optical feedback allowed the tenfold narrowing of the laser line-width with the additional treatment of the “smile” giving a further 30% improvement. The feedback allowed more efficient absorption of the light at much lower pressures. A probe was designed and constructed to measure the polarisation of the rubidium atoms in the two possible levels of the 5S ground state. This probe enabled the rapid optimisation of the polarisation of the rubidium atoms which in turn led to the best polarisation rates measured for the equipment. We have successfully used the hyperpolarised helium from our apparatus to produce high resolution images of lungs of rats that have been kept alive for the duration of the experiments on a ventilator system. These images far surpass the quality of lung images from standard MRI techniques. We also used the hyperpolarised xenon gas to measure pore sizes in mesoporous solids by detecting the shift in the xenon resonance frequency caused by the interaction with the material, and we investigated the effect on the frequency shift of water absorbed in the material. The pore sizes of the materials ranged from 2.5 to 16 nm.

DOI
10.14264/155174

Related papers

Optické čerpání atomů rubidia pomocí Ti:Sa laseru

Z. Buchta

The rapidly growing interest in production of hyperpolarized noble gasses (HpG), predominantly 3He and l29Xe for Nuclear Magnetic Resonance (NMR) experiments is driven by potentially attractive medical applications. Neither helium nor xenon is normally present in the body, so the experiments do not suffer from unwanted background signals. Among the potential medicine applications, the opportunity to image organs with low water content and/or with air spaces, such as colon or lungs, has raised a considerable interest. Current conventional imaging techniques cannot provide good images of these hollow spaces. These applications show that HpG may become a useful tool for non-invasive investigation of human lung ventilation, giving access to static imaging during breathhold, dynamics of inspiration/expiration, and functional imaging. This paper describe the way of optical pumping of Rb vapour by Ti:Sa laser which is necessary for attainment hyperpolarized state of 129Xe

•Jan 1, 2004•0 citations

The xenon hyperpolarization by alexandrite laser spin exchange optical pumping

A. G. Putilov, А. А. Антипов, Alexandr Shepelev

This paper shows the possibility of the use of a solid-state alexandrite laser as a radiation source for the method of spin-exchange optical pumping of noble gases (xenon, krypton). The use of dispersive optical elements in the laser cavity will allows the adjusting of the radiation wavelength exactly in the rubidium spectral absorption lines 794.7 nm and 780 nm. To obtain a hyperpolarized state of noble gases, it is necessary to excite rubidium atoms for further spin-exchange process with the noble gas nuclei. This fact will allow the increasing of the magnetic resonance imaging contrast in the field of diagnosis of respiratory organs diseases.

EPJ Web of Conferences•Jan 1, 2019•3 citations

Generation and detection of hyperpolarized xenon

Zdeněk Buchta, Jan Rychnovský, Zenon Starčuk +1 more

We present the experimental results of generation and of detection of hyperpolarized xenon obtained by 4.7 T, 200 MHz magnetic resonance (MR) system. Xenon 129 was hyperpolarized by the spin-exchange with Rubidium pumped first by Ti:Sa laser and also by extended cavity laser system based on a high-power laser diode optimized for maximum efficiency of the optical pumping process. The application of the arrangement with semiconductor laser system is oriented medicine, especially to continuous production of hyperpolarized Xenon (HpXe) which serves as an contrast media in MR imaging systems.

IEEE AFRICON•Sep 1, 2007•0 citations

Metastability Exchange Optical Pumping of 3He at High Pressure and 1.5T Magnetic Field

M Abboud, A Sinatra, Xavier Maître +2 more

Polarized helium-3 is used in various fields of science, either to prepare spin filters for neutrons [1] and polarized targets for nuclear physics [2], or to perform magnetic resonance imaging (MRI) of air spaces in human lungs [3]. Clinical studies to demonstrate the relevance of polarized gas MRI are under way in the United States and in Europe. Yet, if a wide expertise exists in MRI to adapt the existing proton imaging techniques to polarized helium-3, the large scale dissemination of polarized gas MRI crucially depends on reliable and handy techniques to produce the gas. Two methods are presently used to polarize helium-3: spin-exchange with optically pumped alkali atoms, and pure-helium metastability exchange optical pumping (MEOP). MEOP relies on optical pumping of the 2³S metastable state of helium-3 with 1083 nm resonant light followed by metastability exchange collisions to transfer nuclear polarization to ground state helium-3 atoms. MEOP is usually performed at low magnetic field. It provides high nuclear polarization (up to 80%) at 1 mbar, but its efficiency rapidly decreases as pressure increases [4,5]. Therefore, a delicate polarization-preserving compression stage is necessary for all applications requiring a dense sample. In our study, we demonstrate a new optical pumping scheme for helium-3 at 1.5 T that yields systematically high nuclear polarizations in a pressure range where standard MEOP is very inefficient (e.g. 56% of nuclear polarization at 32 mbar) [6]. From a practical point of view, the new optical pumping scheme opens the way to the development of a helium-3 polarizer operating at relatively high pressure and at 1.5 T, a widely used field in clinical MRI. Experiments are performed in the bore of a 1.5 T clinical MRI system. Cells filled with 1.33 up to 67 mbar of pure helium-3 are used. A radio-frequency discharge is used to populate the 2³S state. The optical pumping laser is a single mode laser diode amplified to 0.5 W. Nuclear polarization is obtained from 1083 nm light absorption measurements, a technique suitable for arbitrary magnetic field and pressure [7]. We have developed a model that describes the effects of the metastability exchange collisions and the optical pumping processes at 1.5 T. Computed photon efficiencies, absorptions, and pumping rates agree with experimental results. We use this theoretical model to characterize the additional relaxation process induced by the pumping laser. We discuss why strong hyperfine decoupling at 1.5 T does not hamper MEOP and improves its efficiency at high pressure.

•Jul 6, 2004•0 citations

Characterizing and modeling the efficiency limits in large-scale production of hyperpolarized Xe129

Matthew S. Freeman, Kiarash Emami, Bastiaan Driehuys

The ability to produce liter volumes of highly-spin-polarized $^{129}\mathrm{Xe}$ enables a wide range of investigations, most notably in the fields of materials science and biomedical magnetic resonance imaging. However, for nearly all polarizers built to date, both peak $^{129}\mathrm{Xe}$ polarization and the rate at which it is produced fall far below those predicted by the standard model of Rb metal vapor, spin-exchange optical pumping (SEOP). In this work we comprehensively characterized a high-volume flow-through $^{129}\mathrm{Xe}$ polarizer using three different SEOP cells with internal volumes of 100, 200, and $300\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{3}$ and two types of optical sources: a broad-spectrum 111-W laser [full width at half maximum (FWHM) equal to 1.92 nm] and a line-narrowed 71-W laser (FWHM equal to 0.39 nm). By measuring $^{129}\mathrm{Xe}$ polarization as a function of gas flow rate, we extracted the peak polarization and polarization production rate across a wide range of laser absorption levels. Peak polarization for all cells consistently remained a factor of 2--3 times lower than predicted at all absorption levels. Moreover, although production rates increased with laser absorption, they did so much more slowly than predicted by the standard theoretical model and basic spin-exchange efficiency arguments. Underperformance was most notable in the smallest optical cells. We propose that all these systematic deviations from theory can be explained by invoking the presence of paramagnetic Rb clusters within the vapor. Cluster formation within saturated alkali-metal vapors is well established and their interaction with resonant laser light was recently shown to create plasmalike conditions. Such cluster systems cause both Rb and $^{129}\mathrm{Xe}$ depolarization, as well as excess photon scattering. These effects were incorporated into the SEOP model by assuming that clusters are activated in proportion to excited-state Rb number density and by further estimating physically reasonable values for the nanocluster-induced velocity-averaged spin-destruction cross section for Rb $(\ensuremath{\langle}{\ensuremath{\sigma}}_{\text{cluster-Rb}}v\ensuremath{\rangle}\phantom{\rule{0.16em}{0ex}}\ensuremath{\approx}\phantom{\rule{0.16em}{0ex}}4\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}7}\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{3}\phantom{\rule{0.16em}{0ex}}{\mathrm{s}}^{\ensuremath{-}1})$, the $^{129}\mathrm{Xe}$ relaxation cross section $(\ensuremath{\langle}{\ensuremath{\sigma}}_{\text{cluster-Xe}}v\ensuremath{\rangle}\phantom{\rule{0.16em}{0ex}}\ensuremath{\approx}\phantom{\rule{0.16em}{0ex}}4\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}13}\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{3}\phantom{\rule{0.16em}{0ex}}{\mathrm{s}}^{\ensuremath{-}1})$, and a non-wavelength-specific photon-scattering cross section $({\ensuremath{\sigma}}_{\mathrm{cluster}}\phantom{\rule{0.16em}{0ex}}\ensuremath{\approx}\phantom{\rule{0.16em}{0ex}}1\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}12}\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{2})$. The resulting modified SEOP model now closely matches experimental observations.

Physical Review A•Aug 6, 2014•55 citations

High-volume production of laser-polarized 129Xe

Bastiaan Driehuys, G. D. Cates, E. Miron +3 more

A method is described for producing several liters of nuclear spin polarized 129Xe gas via spin exchange with an optically pumped Rb vapor. We use a 140 W AlGaAs laser diode array whose broad spectral output is efficiently absorbed by employing ∼10 atm of 4He to pressure broaden the Rb D1 absorption profile. 129Xe is polarized in a continuous gas flow and is then cryogenically accumulated and stored. Extensions of this technique should enable the production of tens of liters of 129Xe with a nuclear spin polarization of order 50%. Production of laser-polarized 129Xe in liter quantities is important for the continued development of magnetic resonance imaging using spin-polarized 129Xe.

Applied Physics Letters•Sep 16, 1996•337 citations
In this thesis I discuss experiments to create hyperpolarised noble gases. In particular, we have constructed an apparatus to hyperpolarise helium and xenon gases and used these resources to image the lungs of living rats and probe the physical properties of mesoporous solids. The apparatus uses a line-width narrowed laser diode array to optically pump rubidium vapour which then polarises the noble gases through spin-exchange collisions. We have also developed techniques to optimise both the amount and rate of polarisation. Using these techniques, we have shown that the apparatus can produce hyperpolarised helium in 350mL volumes with a polarisation of up to 25%. It can also produce hyperpolarised xenon in a continuous flow which results in 10% polarisation of the xenon at a rate of 1018 polarised atoms per minute with only four watts of laser light incident on the cell. The optical feedback system for laser diode arrays was improved to correct for the divergence of the beam caused by curvature in the array of diode elements. This curvature of the array is an artifact of the manufacturing process and causes an increase in the full width half maximum (FWHM) achievable for the spectral profile of the array when using optical feedback to spectrally narrow the laser diode array. The optical feedback allowed the tenfold narrowing of the laser line-width with the additional treatment of the “smile” giving a further 30% improvement. The feedback allowed more efficient absorption of the light at much lower pressures. A probe was designed and constructed to measure the polarisation of the rubidium atoms in the two possible levels of the 5S ground state. This probe enabled the rapid optimisation of the polarisation of the rubidium atoms which in turn led to the best polarisation rates measured for the equipment. We have successfully used the hyperpolarised helium from our apparatus to produce high resolution images of lungs of rats that have been kept alive for the duration of the experiments on a ventilator system. These images far surpass the quality of lung images from standard MRI techniques. We also used the hyperpolarised xenon gas to measure pore sizes in mesoporous solids by detecting the shift in the xenon resonance frequency caused by the interaction with the material, and we investigated the effect on the frequency shift of water absorbed in the material. The pore sizes of the materials ranged from 2.5 to 16 nm.
The rapidly growing interest in production of hyperpolarized noble gasses (HpG), predominantly 3He and l29Xe for Nuclear Magnetic Resonance (NMR) experiments is driven by potentially attractive medical applications. Neither helium nor xenon is normally present in the body, so the experiments do not suffer from unwanted background signals. Among the potential medicine applications, the opportunity to image organs with low water content and/or with air spaces, such as colon or lungs, has raised a considerable interest. Current conventional imaging techniques cannot provide good images of these hollow spaces. These applications show that HpG may become a useful tool for non-invasive investigation of human lung ventilation, giving access to static imaging during breathhold, dynamics of inspiration/expiration, and functional imaging. This paper describe the way of optical pumping of Rb vapour by Ti:Sa laser which is necessary for attainment hyperpolarized state of 129Xe
This paper shows the possibility of the use of a solid-state alexandrite laser as a radiation source for the method of spin-exchange optical pumping of noble gases (xenon, krypton). The use of dispersive optical elements in the laser cavity will allows the adjusting of the radiation wavelength exactly in the rubidium spectral absorption lines 794.7 nm and 780 nm. To obtain a hyperpolarized state of noble gases, it is necessary to excite rubidium atoms for further spin-exchange process with the noble gas nuclei. This fact will allow the increasing of the magnetic resonance imaging contrast in the field of diagnosis of respiratory organs diseases.
We present the experimental results of generation and of detection of hyperpolarized xenon obtained by 4.7 T, 200 MHz magnetic resonance (MR) system. Xenon 129 was hyperpolarized by the spin-exchange with Rubidium pumped first by Ti:Sa laser and also by extended cavity laser system based on a high-power laser diode optimized for maximum efficiency of the optical pumping process. The application of the arrangement with semiconductor laser system is oriented medicine, especially to continuous production of hyperpolarized Xenon (HpXe) which serves as an contrast media in MR imaging systems.
Polarized helium-3 is used in various fields of science, either to prepare spin filters for neutrons [1] and polarized targets for nuclear physics [2], or to perform magnetic resonance imaging (MRI) of air spaces in human lungs [3]. Clinical studies to demonstrate the relevance of polarized gas MRI are under way in the United States and in Europe. Yet, if a wide expertise exists in MRI to adapt the existing proton imaging techniques to polarized helium-3, the large scale dissemination of polarized gas MRI crucially depends on reliable and handy techniques to produce the gas. Two methods are presently used to polarize helium-3: spin-exchange with optically pumped alkali atoms, and pure-helium metastability exchange optical pumping (MEOP). MEOP relies on optical pumping of the 2³S metastable state of helium-3 with 1083 nm resonant light followed by metastability exchange collisions to transfer nuclear polarization to ground state helium-3 atoms. MEOP is usually performed at low magnetic field. It provides high nuclear polarization (up to 80%) at 1 mbar, but its efficiency rapidly decreases as pressure increases [4,5]. Therefore, a delicate polarization-preserving compression stage is necessary for all applications requiring a dense sample. In our study, we demonstrate a new optical pumping scheme for helium-3 at 1.5 T that yields systematically high nuclear polarizations in a pressure range where standard MEOP is very inefficient (e.g. 56% of nuclear polarization at 32 mbar) [6]. From a practical point of view, the new optical pumping scheme opens the way to the development of a helium-3 polarizer operating at relatively high pressure and at 1.5 T, a widely used field in clinical MRI. Experiments are performed in the bore of a 1.5 T clinical MRI system. Cells filled with 1.33 up to 67 mbar of pure helium-3 are used. A radio-frequency discharge is used to populate the 2³S state. The optical pumping laser is a single mode laser diode amplified to 0.5 W. Nuclear polarization is obtained from 1083 nm light absorption measurements, a technique suitable for arbitrary magnetic field and pressure [7]. We have developed a model that describes the effects of the metastability exchange collisions and the optical pumping processes at 1.5 T. Computed photon efficiencies, absorptions, and pumping rates agree with experimental results. We use this theoretical model to characterize the additional relaxation process induced by the pumping laser. We discuss why strong hyperfine decoupling at 1.5 T does not hamper MEOP and improves its efficiency at high pressure.
The ability to produce liter volumes of highly-spin-polarized 129Xe^{129}\mathrm{Xe}129Xe enables a wide range of investigations, most notably in the fields of materials science and biomedical magnetic resonance imaging. However, for nearly all polarizers built to date, both peak 129Xe^{129}\mathrm{Xe}129Xe polarization and the rate at which it is produced fall far below those predicted by the standard model of Rb metal vapor, spin-exchange optical pumping (SEOP). In this work we comprehensively characterized a high-volume flow-through 129Xe^{129}\mathrm{Xe}129Xe polarizer using three different SEOP cells with internal volumes of 100, 200, and 300cm3300\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{3}300cm3 and two types of optical sources: a broad-spectrum 111-W laser [full width at half maximum (FWHM) equal to 1.92 nm] and a line-narrowed 71-W laser (FWHM equal to 0.39 nm). By measuring 129Xe^{129}\mathrm{Xe}129Xe polarization as a function of gas flow rate, we extracted the peak polarization and polarization production rate across a wide range of laser absorption levels. Peak polarization for all cells consistently remained a factor of 2--3 times lower than predicted at all absorption levels. Moreover, although production rates increased with laser absorption, they did so much more slowly than predicted by the standard theoretical model and basic spin-exchange efficiency arguments. Underperformance was most notable in the smallest optical cells. We propose that all these systematic deviations from theory can be explained by invoking the presence of paramagnetic Rb clusters within the vapor. Cluster formation within saturated alkali-metal vapors is well established and their interaction with resonant laser light was recently shown to create plasmalike conditions. Such cluster systems cause both Rb and 129Xe^{129}\mathrm{Xe}129Xe depolarization, as well as excess photon scattering. These effects were incorporated into the SEOP model by assuming that clusters are activated in proportion to excited-state Rb number density and by further estimating physically reasonable values for the nanocluster-induced velocity-averaged spin-destruction cross section for Rb $(\ensuremath{\langle}{\ensuremath{\sigma}}_{\text{cluster-Rb}}v\ensuremath{\rangle}\phantom{\rule{0.16em}{0ex}}\ensuremath{\approx}\phantom{\rule{0.16em}{0ex}}4\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}7}\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{3}\phantom{\rule{0.16em}{0ex}}{\mathrm{s}}^{\ensuremath{-}1})$, the 129Xe^{129}\mathrm{Xe}129Xe relaxation cross section $(\ensuremath{\langle}{\ensuremath{\sigma}}_{\text{cluster-Xe}}v\ensuremath{\rangle}\phantom{\rule{0.16em}{0ex}}\ensuremath{\approx}\phantom{\rule{0.16em}{0ex}}4\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}13}\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{3}\phantom{\rule{0.16em}{0ex}}{\mathrm{s}}^{\ensuremath{-}1})$, and a non-wavelength-specific photon-scattering cross section $({\ensuremath{\sigma}}_{\mathrm{cluster}}\phantom{\rule{0.16em}{0ex}}\ensuremath{\approx}\phantom{\rule{0.16em}{0ex}}1\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}12}\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{2})$. The resulting modified SEOP model now closely matches experimental observations.
A method is described for producing several liters of nuclear spin polarized 129Xe gas via spin exchange with an optically pumped Rb vapor. We use a 140 W AlGaAs laser diode array whose broad spectral output is efficiently absorbed by employing ∼10 atm of 4He to pressure broaden the Rb D1 absorption profile. 129Xe is polarized in a continuous gas flow and is then cryogenically accumulated and stored. Extensions of this technique should enable the production of tens of liters of 129Xe with a nuclear spin polarization of order 50%. Production of laser-polarized 129Xe in liter quantities is important for the continued development of magnetic resonance imaging using spin-polarized 129Xe.