Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

The Journal of Physical Chemistry A

Two-photon Excited Fluorescence of Nitrogen-Vacancy Centers in Proton-Irradiated Type Ib Diamond

Tse-Luen Wee, Yan‐Kai Tzeng, C.-C. Han, Huan‐Cheng Chang, Wunshain S. Fann, Jui‐Hung Hsu, Kuan‐Ming Chen, Yueh‐Chung Yu

Published Aug 18, 2007• 198 citations
Publisher

Abstract

Two-photon fluorescence spectroscopy of negatively charged nitrogen-vacancy [(N-V)-] centers in type Ib diamond single crystals have been studied with a picosecond (7.5 ps) mode-locked Nd:YVO(4) laser operating at 1064 nm. The (N-V)- centers were produced by radiation damage of diamond using a 3 MeV proton beam, followed by thermal annealing at 800 degrees C. Prior to the irradiation treatment, infrared spectroscopy of the C-N vibrational modes at 1344 cm(-1) suggested a nitrogen content of 109 +/- 10 ppm. Irradiation and annealing of the specimen led to the emergence of a new absorption band peaking at approximately 560 nm. From a measurement of the integrated absorption intensity of the sharp zero-phonon line (637 nm) at liquid nitrogen temperature, we determined a (N-V)- density of (4.5 +/- 1.1) x 10(18) centers/cm3 (or 25 +/- 6 ppm) for the substrate irradiated at a dose of 1 x 1016) H(+)/cm(2). Such a high defect density allowed us to observe two-photon excited fluorescence and measure the corresponding fluorescence decay time. No significant difference in the spectral feature and fluorescence lifetime was observed between one-photon and two-photon excitations. Assuming that the fluorescence quantum yields are the same for both processes, a two-photon absorption cross section of sigma(TPA) = (0.45 +/- 0.23) x 10(-50) cm(4).s/photon at 1064 nm was determined for the (N-V)- center based on its one-photon absorption cross section of sigma(OPA) = (3.1 +/- 0.8) x 10(-17) cm2 at 532 nm. The material is highly photostable and shows no sign of photobleaching even under continuous two-photon excitation at a peak power density of 3 GW/cm(2) for 5 min.

DOI
10.1021/jp073938o

Related papers

Multiple-photon excitation of nitrogen vacancy centers in diamond

Peng Ji, Ryan Balili, Jonathan Beaumariage +3 more

We report the observation of multiphoton photoluminescence excitation (PLE) below the resonant energies of nitrogen vacancy (NV) centers in diamond. The quadratic and cubic dependence of the integrated fluorescence intensity as a function of excitation power indicates a two-photon excitation pathway for the ${\mathrm{NV}}^{\ensuremath{-}}$ charge state and a three-photon process involved for the neutral ${\mathrm{NV}}^{0}$ charge state, respectively. Comparing the total multiphoton energy with its single-photon equivalent, the PLE spectra follows the absorption spectrum of single photon excitation. We also observed that the efficiency of photoluminescence for different charge states, as well as the decay time constant, was dependent on the excitation wavelength and power.

arXiv:1710.07539•Physical review. B./Physical review. B•Apr 17, 2018•27 citations

Engineering Nitrogen-Vacancy Centers in Nano-diamonds for Single Photon Emission

Ravi Kumar, Sung‐June Yoon, Kwanggeol Lee +4 more

Defects in diamond have evolved as unique object for their potential application for Optical imaging and Nano-photonics. High pressure high temperature (HPHT) grown type-Ib diamond particles were milled down to the size of ~ 80 nm and purified to remove iron & graphitic carbon impurities and irradiated with 35 KeV He+ ions to create vacancies in the diamond lattice. Vacancies diffuse close to substitutional nitrogen impurities of nano-diamond particles upon thermal treatment. Characteristic sharp emission of NV centers were observed at 575.5 nm and 637.9 nm corresponding to NV° and NV− charged states in addition to a broad emission in the range 550-750 nm. Structural and photo-physical behavior of these fluorescent diamonds was found to depend on the method of purification adopted. Samples purified through acid reflux were found suitable for bio-imaging applications while, sample purified through air oxidation shows properties desirable for Nano-photonic applications. Photon-correlation measurements of emission from individual diamond nanoparticles using Hanbury Brown and Twiss interferometer (HBT) shows anti-bunching curve with g2(t)= 0 confirming their suitability as single photon source. Such sources of indistinguishable photons are highly desirable for quantum computation and quantum optics applications.

International conference on fiber optics and photonics•Jan 1, 2016•0 citations

Laser spectroscopic characterization of negatively charged nitrogen-vacancy (NV−) centers in diamond

Shova D. Subedi, Vladimir Fedorov, Jeremy M. Peppers +4 more

We report on the spectroscopic and laser characterization of negatively charged nitrogen-vacancy (NV−) centers in diamond. Spectroscopic properties such as absorption and emission spectra as well as kinetics were studied, and parameters such as cross-sections and lifetimes were estimated. A vibronic band of NV0 with zero phonon line (ZPL) at 575 nm was detected under 532 nm pulsed excitation due to the photoionization of NV−. Transmission of 532 nm pump pulses saturate around ∼10%, which is much smaller than the theoretical level. Δk/k0 kinetics revealed slow recovery of NV− centers after photoionization under 532 nm pumping, which involved different relaxation channels depending on the probe beam wavelengths. Localization of the electrons in the metastable state of NV0 centers resulted in higher saturated transmission of 632 nm pump.

Optical Materials Express•Apr 5, 2019•73 citations

A single photon source based on NV centers in diamond nanocrystals

Juliane Bahe, Xiaoqing Zhou, Tobias Jan Kippenberg +4 more

The development of reliable devices to generate single photons is crucial for applications in quantum cryptography, as well as for fundamental quantum optics experiments. Due to their extremely high photostability at room temperature, optically active defects in solids, the so called color centers, are among the most promising candidates. Single NV (nitrogen-vacancy) centers in diamond have been demonstrated to be able to generate single photons and have already shown advantages compared to attenuated laser pulses in a quantum cryptography experiment. The nitrogen-vacancy center (NV center) in diamond consists of a substitutional nitrogen atom and an adjacent vacancy. This complex exhibits an optical transition with a fluorescence lifetime of 11.6 ns. The room temperature spectrum of the NV center consists of the zero-phonon line at 637 nm and broad phononic sidebands with a FWHM of more than 100 nm. Due to the existence of a shelving level the efficiency of the NV center as a single photon source is limited. Additionally, the high diffraction index of bulk diamond restricts the efficiency to collect the fluorescence light.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 1, 2009•4 citations

Creation of ensembles of nitrogen-vacancy centers in diamond by neutron and electron irradiation

Tobias Nöbauer, K. Buczak, Andreas Angerer +7 more

We created dense ensembles of negatively charged nitrogen-vacancy (NV-) centers in diamond by neutron and electron irradiation for applications in hybrid quantum systems and magnetometry. We characterize fluorescence intensity, optical and coherence properties of the resulting defects by confocal microscopy, UV/Vis and FTIR spectroscopy, optically detected magnetic resonance and small angle X-ray scattering. We find the highest densities of NV- at neutron fluences on the order of 10^17 cm^-2 and electron doses of 10^18 cm^-2, with spin resonance linewidths of 6 MHz. Lower electron energies increase the ratio of centers in the desired negative charge state to those in the neutral one. Annealing at 900 °C during the irradiation reduces the spin resonance linewidth. Electron irradiation furthermore results in substantially higher optical transparency compared to neutron irradiation.

arXiv:1309.0453•Sep 2, 2013•28 citations

Effects of Electron Irradiation and Anneal Condition on Creation of Nitrogen-Vacancy Centers in Ib Diamonds

Ishii Shuya, Onoda Shinobu, Abe Hiroshi +1 more

Electron irradiation is one of the most powerful methods to create negatively charged nitrogen-vacancy centers (NV-s) in diamonds, which act as qubits and quantum sensors even at room temperature (RT). For quantum sensing, it is important to create ensemble NV-s with long coherence time (T2) since the sensitivity can be affected by both amount of NV- and T2. For high concentration NV-, electron irradiation with higher fluence is needed. However, if electron fluence is too high, neutral NVs (NV0s) are created because of lack of N donors. For T2, since residual defects act as origins of T2 decoherence, it is important to optimize the condition of subsequent annealing as well as irradiation fluence. Thus, we need to consider initial nitrogen (P1) concentration in diamond, electron fluence, and annealing conditions. In this paper, we create NV-s in Ib diamonds by electron irradiation and subsequent annealing with different conditions, and study the amounts of NV-s and their T2 for high-sensitive quantum sensing. The samples used in this study were Ib diamond with P1 concentration around 100 ppm. Those samples were irradiated with 2 MeV-electrons at a fluence of 1x1018/cm2 at RT. After irradiation, the samples were annealed between 600 and 1400oC in Ar. Photoluminescence (PL) measurements were carried out at RT to confirm NV creation. For PL measurements, the laser with a wavelength of 532 nm was used as excitation. PL intensity for samples annealed at 600 oC is about half even after annealing for 600 min, comparing with that for 800 oC-annealed samples although the values increase with increasing annealing time. Thus, the annealing at 650 oC is not enough to create NV. The samples annealed between 800 and 1200 oC show the highest PL intensity even after annealing for 10 min. The 800 and 1000 oC-annealed samples keep the PL intensity after annealing for 1200 min although the PL intensity for 1200 oC-annealed samples decrease with increasing annealing time above 100 min. The PL intensity for the samples annealed at 1400 oC shows smaller value and decreases with increasing annealing time. For T2, the samples annealed at 1400 oC show 2 microsec after annealing for 10 min. However, NV- cannot be observed after annealing at 1400 oC for 30min. Therefore, it can be concluded that annealing at 1400 oC is not suitable for the creation of NV-. For samples annealed between 600 and 1000 oC, the values of T2 are constant (between 0.5 and 0.9 microsec) after annealing up to 1200 min. For samples annealed at 1200 oC, no significant difference in T2 value is observed from those annealed between 600 and 1000 oC up to 30min, and the value increases with increasing annealing time above 30 min. From the point of view of sensing, it is important to consider both the amounts of NV- centers and T2. Therefore, we compare the values of PL intensity times T2. As a result, the samples annealed between 800 and 1200 oC show the highest value although the value for samples annealed at 1200 oC decreases after annealing for 1200 min. This suggests that annealing at 800 oC for 10 min is enough to create NV-s. We also study the creation of NV-s in diamonds by electron irradiation at elevated temperature. The samples with P1 concentration around 60 and 100 ppm were irradiated with 2 MeV-electrons at fluences up to 5x1018/cm2 at 800 or 1000 oC. The samples were annealed at 1000 oC for 120 min after irradiation. The amounts of NV are estimated from electron spin resonance (ESR) signals. As a result, samples irradiated at 800 and 1000 oC show higher NV- concentration than that for RT-irradiated ones, and 800 oC-irradiated ones show higher NV concentration than 1000oC-irradiated ones. Since the T2 values are not affected by irradiation temperature, the elevated temperature irradiation, especially 800 oC irradiation is a useful method to realize quantum sensing with high sensitivity.

•Jul 10, 2025•0 citations
Two-photon fluorescence spectroscopy of negatively charged nitrogen-vacancy [(N-V)-] centers in type Ib diamond single crystals have been studied with a picosecond (7.5 ps) mode-locked Nd:YVO(4) laser operating at 1064 nm. The (N-V)- centers were produced by radiation damage of diamond using a 3 MeV proton beam, followed by thermal annealing at 800 degrees C. Prior to the irradiation treatment, infrared spectroscopy of the C-N vibrational modes at 1344 cm(-1) suggested a nitrogen content of 109 +/- 10 ppm. Irradiation and annealing of the specimen led to the emergence of a new absorption band peaking at approximately 560 nm. From a measurement of the integrated absorption intensity of the sharp zero-phonon line (637 nm) at liquid nitrogen temperature, we determined a (N-V)- density of (4.5 +/- 1.1) x 10(18) centers/cm3 (or 25 +/- 6 ppm) for the substrate irradiated at a dose of 1 x 1016) H(+)/cm(2). Such a high defect density allowed us to observe two-photon excited fluorescence and measure the corresponding fluorescence decay time. No significant difference in the spectral feature and fluorescence lifetime was observed between one-photon and two-photon excitations. Assuming that the fluorescence quantum yields are the same for both processes, a two-photon absorption cross section of sigma(TPA) = (0.45 +/- 0.23) x 10(-50) cm(4).s/photon at 1064 nm was determined for the (N-V)- center based on its one-photon absorption cross section of sigma(OPA) = (3.1 +/- 0.8) x 10(-17) cm2 at 532 nm. The material is highly photostable and shows no sign of photobleaching even under continuous two-photon excitation at a peak power density of 3 GW/cm(2) for 5 min.
We report the observation of multiphoton photoluminescence excitation (PLE) below the resonant energies of nitrogen vacancy (NV) centers in diamond. The quadratic and cubic dependence of the integrated fluorescence intensity as a function of excitation power indicates a two-photon excitation pathway for the ${\mathrm{NV}}^{\ensuremath{-}}$ charge state and a three-photon process involved for the neutral NV0{\mathrm{NV}}^{0}NV0 charge state, respectively. Comparing the total multiphoton energy with its single-photon equivalent, the PLE spectra follows the absorption spectrum of single photon excitation. We also observed that the efficiency of photoluminescence for different charge states, as well as the decay time constant, was dependent on the excitation wavelength and power.
Defects in diamond have evolved as unique object for their potential application for Optical imaging and Nano-photonics. High pressure high temperature (HPHT) grown type-Ib diamond particles were milled down to the size of ~ 80 nm and purified to remove iron & graphitic carbon impurities and irradiated with 35 KeV He+ ions to create vacancies in the diamond lattice. Vacancies diffuse close to substitutional nitrogen impurities of nano-diamond particles upon thermal treatment. Characteristic sharp emission of NV centers were observed at 575.5 nm and 637.9 nm corresponding to NV° and NV− charged states in addition to a broad emission in the range 550-750 nm. Structural and photo-physical behavior of these fluorescent diamonds was found to depend on the method of purification adopted. Samples purified through acid reflux were found suitable for bio-imaging applications while, sample purified through air oxidation shows properties desirable for Nano-photonic applications. Photon-correlation measurements of emission from individual diamond nanoparticles using Hanbury Brown and Twiss interferometer (HBT) shows anti-bunching curve with g2(t)= 0 confirming their suitability as single photon source. Such sources of indistinguishable photons are highly desirable for quantum computation and quantum optics applications.
We report on the spectroscopic and laser characterization of negatively charged nitrogen-vacancy (NV−) centers in diamond. Spectroscopic properties such as absorption and emission spectra as well as kinetics were studied, and parameters such as cross-sections and lifetimes were estimated. A vibronic band of NV0 with zero phonon line (ZPL) at 575 nm was detected under 532 nm pulsed excitation due to the photoionization of NV−. Transmission of 532 nm pump pulses saturate around ∼10%, which is much smaller than the theoretical level. Δk/k0 kinetics revealed slow recovery of NV− centers after photoionization under 532 nm pumping, which involved different relaxation channels depending on the probe beam wavelengths. Localization of the electrons in the metastable state of NV0 centers resulted in higher saturated transmission of 632 nm pump.
The development of reliable devices to generate single photons is crucial for applications in quantum cryptography, as well as for fundamental quantum optics experiments. Due to their extremely high photostability at room temperature, optically active defects in solids, the so called color centers, are among the most promising candidates. Single NV (nitrogen-vacancy) centers in diamond have been demonstrated to be able to generate single photons and have already shown advantages compared to attenuated laser pulses in a quantum cryptography experiment. The nitrogen-vacancy center (NV center) in diamond consists of a substitutional nitrogen atom and an adjacent vacancy. This complex exhibits an optical transition with a fluorescence lifetime of 11.6 ns. The room temperature spectrum of the NV center consists of the zero-phonon line at 637 nm and broad phononic sidebands with a FWHM of more than 100 nm. Due to the existence of a shelving level the efficiency of the NV center as a single photon source is limited. Additionally, the high diffraction index of bulk diamond restricts the efficiency to collect the fluorescence light.
We created dense ensembles of negatively charged nitrogen-vacancy (NV-) centers in diamond by neutron and electron irradiation for applications in hybrid quantum systems and magnetometry. We characterize fluorescence intensity, optical and coherence properties of the resulting defects by confocal microscopy, UV/Vis and FTIR spectroscopy, optically detected magnetic resonance and small angle X-ray scattering. We find the highest densities of NV- at neutron fluences on the order of 10^17 cm^-2 and electron doses of 10^18 cm^-2, with spin resonance linewidths of 6 MHz. Lower electron energies increase the ratio of centers in the desired negative charge state to those in the neutral one. Annealing at 900 °C during the irradiation reduces the spin resonance linewidth. Electron irradiation furthermore results in substantially higher optical transparency compared to neutron irradiation.
Electron irradiation is one of the most powerful methods to create negatively charged nitrogen-vacancy centers (NV-s) in diamonds, which act as qubits and quantum sensors even at room temperature (RT). For quantum sensing, it is important to create ensemble NV-s with long coherence time (T2) since the sensitivity can be affected by both amount of NV- and T2. For high concentration NV-, electron irradiation with higher fluence is needed. However, if electron fluence is too high, neutral NVs (NV0s) are created because of lack of N donors. For T2, since residual defects act as origins of T2 decoherence, it is important to optimize the condition of subsequent annealing as well as irradiation fluence. Thus, we need to consider initial nitrogen (P1) concentration in diamond, electron fluence, and annealing conditions. In this paper, we create NV-s in Ib diamonds by electron irradiation and subsequent annealing with different conditions, and study the amounts of NV-s and their T2 for high-sensitive quantum sensing. The samples used in this study were Ib diamond with P1 concentration around 100 ppm. Those samples were irradiated with 2 MeV-electrons at a fluence of 1x1018/cm2 at RT. After irradiation, the samples were annealed between 600 and 1400oC in Ar. Photoluminescence (PL) measurements were carried out at RT to confirm NV creation. For PL measurements, the laser with a wavelength of 532 nm was used as excitation. PL intensity for samples annealed at 600 oC is about half even after annealing for 600 min, comparing with that for 800 oC-annealed samples although the values increase with increasing annealing time. Thus, the annealing at 650 oC is not enough to create NV. The samples annealed between 800 and 1200 oC show the highest PL intensity even after annealing for 10 min. The 800 and 1000 oC-annealed samples keep the PL intensity after annealing for 1200 min although the PL intensity for 1200 oC-annealed samples decrease with increasing annealing time above 100 min. The PL intensity for the samples annealed at 1400 oC shows smaller value and decreases with increasing annealing time. For T2, the samples annealed at 1400 oC show 2 microsec after annealing for 10 min. However, NV- cannot be observed after annealing at 1400 oC for 30min. Therefore, it can be concluded that annealing at 1400 oC is not suitable for the creation of NV-. For samples annealed between 600 and 1000 oC, the values of T2 are constant (between 0.5 and 0.9 microsec) after annealing up to 1200 min. For samples annealed at 1200 oC, no significant difference in T2 value is observed from those annealed between 600 and 1000 oC up to 30min, and the value increases with increasing annealing time above 30 min. From the point of view of sensing, it is important to consider both the amounts of NV- centers and T2. Therefore, we compare the values of PL intensity times T2. As a result, the samples annealed between 800 and 1200 oC show the highest value although the value for samples annealed at 1200 oC decreases after annealing for 1200 min. This suggests that annealing at 800 oC for 10 min is enough to create NV-s. We also study the creation of NV-s in diamonds by electron irradiation at elevated temperature. The samples with P1 concentration around 60 and 100 ppm were irradiated with 2 MeV-electrons at fluences up to 5x1018/cm2 at 800 or 1000 oC. The samples were annealed at 1000 oC for 120 min after irradiation. The amounts of NV are estimated from electron spin resonance (ESR) signals. As a result, samples irradiated at 800 and 1000 oC show higher NV- concentration than that for RT-irradiated ones, and 800 oC-irradiated ones show higher NV concentration than 1000oC-irradiated ones. Since the T2 values are not affected by irradiation temperature, the elevated temperature irradiation, especially 800 oC irradiation is a useful method to realize quantum sensing with high sensitivity.