Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Critical Josephson current as a characterization tool for superconducting junction arrays

Brigitte Léridon, Roberto Maoli

Published Nov 1, 1993• 3 citations
Publisher

Abstract

Arrays of Nb/Al-Al2O3/Nb junctions used for heterodyne detection in radioastronomy were measured. Observing the current-voltage curve for different values of the external magnetic field, and interpreting the dc Josephson current, we were able to distinguish the behavior of each junction, and to estimate the inhomogeneities in areas, in critical currents, or in leakage currents among them. This provides an indication of possible cancellation of the Josephson current which is a source of additional noise and polarization instabilities (drop-back) in high-frequency superconductor-insulator-superconductor heterodyne receivers.

DOI
10.1063/1.354204

Related papers

Experimental evidence of Josephson noise in superconductor-insulator-superconductor quasiparticle mixers

Brigitte Léridon, Pascal Febvre, Sylvie George +2 more

Josephson currents have been observed to drain instabilities and decrease the sensitivity of a heterodyne superconductor-insulator-superconductor (SIS) receiver operated at submillimeter wavelengths. A static magnetic field is usually applied on the SIS junction to reduce the magnitude of its critical Josephson currents and enable quasiparticle mixing. We measured the SIS mixer output power at the intermediate frequency (IF) versus the dc bias voltage of an array of two 1 μm2 Nb/Al–Al2O3/Nb junctions. We show evidence of additional, magnetic-field-sensitive noise, peaked at the Shapiro steps voltages, which is due to high-frequency Josephson currents converted to the IF by quasiparticle mixing.

Journal of Applied Physics•Sep 15, 1997•4 citations

Harmonic current-phase relation in Nb–Al-based superconductor/insulator/normal conductor/insulator/superconductor-type Josephson junctions between 4.2 K and the critical temperature

Martin Götz, Vladimir V. Khanin, H. Schulze +6 more

For a study of the supercurrent–phase relationship, we have fabricated Nb/Al/AlOx/Al/AlOx/Al/Nb-based Josephson junctions of low critical current density. At 4.2 K, junctions of a nominal area of 10×10 μm2 showed a nonhysteretic dc current–voltage characteristic with a critical current of about 10 μA. Similar junctions were part of washer-type rf superconductor quantum interference devices. These samples were inductively coupled to high-quality tank circuits for measurements at 4.2 K or at higher temperatures up to values close to the critical temperature of niobium. In this range, the current–phase relation, as deduced from impedance measurements of the phase-biased junction, did not deviate significantly from the sinusoidal shape.

Applied Physics Letters•Aug 28, 2000•5 citations

Fundamental and harmonic submillimeter-wave emission from parallel Josephson junction arrays

Faouzi M. Boussaha, Morvan C. Salez, A. Féret +6 more

We report heterodyne measurements of Josephson microwave radiation emitted by a parallel array of small superconductor-insulator-superconductor (SIS) junctions at submillimeter-wave frequencies. The array consists of five Nb/Al–AlOx/Nb junctions nonevenly distributed in a niobium superconducting stripline, and is optimized for rf coupling in the 450–640 GHz range. We observed Fiske-like resonant steps in its I-V curve in the presence of magnetic field. The device was placed in a waveguide mount, and its radiation was quasioptically coupled out of the cryostat, to a SIS-mixer spectrometer in the same frequency range, with a 4–8 GHz band for spectral analysis. We detected a coherent signal in the spectra when the array was biased on the first and third steps, respectively, at the first harmonic frequency of 242 GHz and at the fundamental frequency of 493 GHz, both being the Josephson frequencies associated with their dc voltages. This strongly suggests that this type of parallel arrays optimized for wideband rf coupling, though strongly discretized, hosts dynamic fluxon regimes similar to long Josephson junctions, which could find applications in superconducting digital electronics or integrated heterodyne submillimeter-wave receivers.

Journal of Applied Physics•Apr 1, 2009•7 citations

Features of the spectrum of a niobium Josephson junction array measured with the use of high-Tc Josephson mixer

Mikhail A. Galin, A. I. El’kina, M. Yu. Levichev +3 more

Spectral measurements of a niobium Josephson junction arrays with overwavelength dimensions have been performed using a heterodyne receiver with a mixer based on a high-Tc bicrystal transition. The array is fabricated on a silicon substrate and is composed from 9996 series connected Nb/NbSi/Nb junctions embedded to parallel single-strip lines with the length 7.1 mm. The mixer in the receiver is a Josephson junction formed by a YBaCuO film on a bicrystal boundary of Zr1−xYxO2 substrate. Spectral measurements have been performed in the frequency ranges 150-180 GHz and 225-250 GHz. The aim of the work was the investigation of the influence to the spectral line from some factors of external electrical circuit: the type of power supply and the level of technical noises. Significant decrease of the linewidth from ~ 10 MHz to 0.5-0.8 MHz has been found at the connection of the array to voltage source instead of current source and at the minimizing of technical noises. The shift of spectral frequency from the Josephson one averaged over the array has been observed that is explained by the peculiarities of synchronization of Josephson junctions in large arrays.

Journal of Radio Electronics•Feb 1, 2025•0 citations

Studies of noise in Josephson-effect mixers and their potential for submillimeter heterodyne detection

Robert J. Schoelkopf

NOTE: Text or symbols not renderable in plain ASCII are indicated by [...]. Abstract is included in .pdf document. This thesis describes both theoretical and experimental investigations into the dynamics and noise processes of Josephson junctions, with the intent of evaluating their potential as mixers in heterodyne instruments for submillimeter-wave (i.e., the frequency range from 300 GHz to 3THz) detection. Superconducting tunnel junctions utilizing the nonlinearity due to photon-assisted tunneling of quasiparticles (SIS mixers) have become the state-of-the-art technology for sensitive heterodyne detection up to frequencies of about 700 [...]. Recent progress in the fabrication of high [...], superconductors has led to Josephson-effect devices with [...] products of up to ten millivolts, which might be suitable for mixing at frequencies of many terahertz. The key question for weighing the prospects for high-frequency Josephson mixers is that of the sensitivity which can be attained. Previous experimental work on Josephson mixing suggests the existence of an "excess" noise, which degrades the sensitivity. Theoretical modeling of mixer performance, based on the resistivelyshunted junction (RSJ) model for the dynamics of the device, also indicates the presence of larger noise than expected. The origin of this noise was not clearly understood, however, nor was its exact magnitude or expected scaling with frequency or junction characteristics known. In addition, previous experiments utilized crude devices of the point-contact type, which were unstable and thus undesirable for real applications. In the first part of this thesis research, extensive numerical simulations were performed with the RSJ model, including calculations of mixer noise and conversion efficiency. These calculations have revealed that the source of excess noise is the AC Josephson oscillations of the device, which can be completely incoherent, with a linewidth comparable to their frequency. Thus they appear as a broadband noise source. While this noise is intrinsic and unavoidable, an optimized mixer is still shown to be capable of interesting sensitivity levels, and the excess noise is expected to become relatively less important as the operating frequency is increased. Secondly, a process has been developed for the fabrication of stable, well-characterized, and reproducible Josephson devices based on resistively-shunted Nb and NbN tunnel junctions. The devices utilize submicron-area, high current-density tunnel junctions and a AuGe shunt resistor to yield completely non-hysteretic I-V curves, normal-state resistances of about [...] products of about half a millivolt. These devices should be nearly optimal for mixing at [...]. Heterodyne measurements using these junctions have been performed in a waveguide mixer mount. Receiver temperatures as low as 190 K (DSB), with -6 dB conversion efficiency, have been obtained at 100 [...], but these results are still a factor of about four higher than those predicted by the RSJ simulations. Accurate measurements of the available noise power of the junctions at the intermediate frequency of 1.5 [...] were made, and confirmed that the receivers were limited by elevated junction output noise. The deviations of the noise from theoretical predictions are shown to be caused by the nonlinear interaction of the junction with the embedding circuit. While this work points out some of the complexity introduced by the strong nonlinearity of Josephson devices, it is still expected that Josephson-effect mixers may be useful for heterodyne detection at very high frequencies.

•Nov 7, 2007•5 citations

Features of the Spectrum of a Niobium Josephson Junction Array Measured with the Use of High-Tc, Josephson Mixer

Mikhail A. Galin, A. I. El’kina, M. Yu. Levichev +3 more

We performed spectral measurements of a large niobium Josephson junctions array. The array consists of 9996 serially connected Nb/NbSi/Nb junctions placed on a 1×1 cm silicon substrate. The spectrum was analyzed by a heterodyne superconducting receiver based on a high-TcJosephson mixer. It was discovered that the linewidth of Josephson radiation is strongly influenced by configuration and type of a measurement system. We obtain the linewidth down to 0.2 MHz when connecting the array to an autonomous power source and minimizing technical noise. We also observed the shift of the spectral frequency from the Josephson one that can be explained by peculiarities of synchronization of such large multi-oscillator systems.

IEEE All-Russian Microwave Conference (RMC)•Nov 25, 2024•0 citations
Arrays of Nb/Al-Al2O3/Nb junctions used for heterodyne detection in radioastronomy were measured. Observing the current-voltage curve for different values of the external magnetic field, and interpreting the dc Josephson current, we were able to distinguish the behavior of each junction, and to estimate the inhomogeneities in areas, in critical currents, or in leakage currents among them. This provides an indication of possible cancellation of the Josephson current which is a source of additional noise and polarization instabilities (drop-back) in high-frequency superconductor-insulator-superconductor heterodyne receivers.
Josephson currents have been observed to drain instabilities and decrease the sensitivity of a heterodyne superconductor-insulator-superconductor (SIS) receiver operated at submillimeter wavelengths. A static magnetic field is usually applied on the SIS junction to reduce the magnitude of its critical Josephson currents and enable quasiparticle mixing. We measured the SIS mixer output power at the intermediate frequency (IF) versus the dc bias voltage of an array of two 1 μm2 Nb/Al–Al2O3/Nb junctions. We show evidence of additional, magnetic-field-sensitive noise, peaked at the Shapiro steps voltages, which is due to high-frequency Josephson currents converted to the IF by quasiparticle mixing.
For a study of the supercurrent–phase relationship, we have fabricated Nb/Al/AlOx/Al/AlOx/Al/Nb-based Josephson junctions of low critical current density. At 4.2 K, junctions of a nominal area of 10×10 μm2 showed a nonhysteretic dc current–voltage characteristic with a critical current of about 10 μA. Similar junctions were part of washer-type rf superconductor quantum interference devices. These samples were inductively coupled to high-quality tank circuits for measurements at 4.2 K or at higher temperatures up to values close to the critical temperature of niobium. In this range, the current–phase relation, as deduced from impedance measurements of the phase-biased junction, did not deviate significantly from the sinusoidal shape.
We report heterodyne measurements of Josephson microwave radiation emitted by a parallel array of small superconductor-insulator-superconductor (SIS) junctions at submillimeter-wave frequencies. The array consists of five Nb/Al–AlOx/Nb junctions nonevenly distributed in a niobium superconducting stripline, and is optimized for rf coupling in the 450–640 GHz range. We observed Fiske-like resonant steps in its I-V curve in the presence of magnetic field. The device was placed in a waveguide mount, and its radiation was quasioptically coupled out of the cryostat, to a SIS-mixer spectrometer in the same frequency range, with a 4–8 GHz band for spectral analysis. We detected a coherent signal in the spectra when the array was biased on the first and third steps, respectively, at the first harmonic frequency of 242 GHz and at the fundamental frequency of 493 GHz, both being the Josephson frequencies associated with their dc voltages. This strongly suggests that this type of parallel arrays optimized for wideband rf coupling, though strongly discretized, hosts dynamic fluxon regimes similar to long Josephson junctions, which could find applications in superconducting digital electronics or integrated heterodyne submillimeter-wave receivers.
Spectral measurements of a niobium Josephson junction arrays with overwavelength dimensions have been performed using a heterodyne receiver with a mixer based on a high-Tc bicrystal transition. The array is fabricated on a silicon substrate and is composed from 9996 series connected Nb/NbSi/Nb junctions embedded to parallel single-strip lines with the length 7.1 mm. The mixer in the receiver is a Josephson junction formed by a YBaCuO film on a bicrystal boundary of Zr1−xYxO2 substrate. Spectral measurements have been performed in the frequency ranges 150-180 GHz and 225-250 GHz. The aim of the work was the investigation of the influence to the spectral line from some factors of external electrical circuit: the type of power supply and the level of technical noises. Significant decrease of the linewidth from ~ 10 MHz to 0.5-0.8 MHz has been found at the connection of the array to voltage source instead of current source and at the minimizing of technical noises. The shift of spectral frequency from the Josephson one averaged over the array has been observed that is explained by the peculiarities of synchronization of Josephson junctions in large arrays.
NOTE: Text or symbols not renderable in plain ASCII are indicated by [...]. Abstract is included in .pdf document. This thesis describes both theoretical and experimental investigations into the dynamics and noise processes of Josephson junctions, with the intent of evaluating their potential as mixers in heterodyne instruments for submillimeter-wave (i.e., the frequency range from 300 GHz to 3THz) detection. Superconducting tunnel junctions utilizing the nonlinearity due to photon-assisted tunneling of quasiparticles (SIS mixers) have become the state-of-the-art technology for sensitive heterodyne detection up to frequencies of about 700 [...]. Recent progress in the fabrication of high [...], superconductors has led to Josephson-effect devices with [...] products of up to ten millivolts, which might be suitable for mixing at frequencies of many terahertz. The key question for weighing the prospects for high-frequency Josephson mixers is that of the sensitivity which can be attained. Previous experimental work on Josephson mixing suggests the existence of an "excess" noise, which degrades the sensitivity. Theoretical modeling of mixer performance, based on the resistivelyshunted junction (RSJ) model for the dynamics of the device, also indicates the presence of larger noise than expected. The origin of this noise was not clearly understood, however, nor was its exact magnitude or expected scaling with frequency or junction characteristics known. In addition, previous experiments utilized crude devices of the point-contact type, which were unstable and thus undesirable for real applications. In the first part of this thesis research, extensive numerical simulations were performed with the RSJ model, including calculations of mixer noise and conversion efficiency. These calculations have revealed that the source of excess noise is the AC Josephson oscillations of the device, which can be completely incoherent, with a linewidth comparable to their frequency. Thus they appear as a broadband noise source. While this noise is intrinsic and unavoidable, an optimized mixer is still shown to be capable of interesting sensitivity levels, and the excess noise is expected to become relatively less important as the operating frequency is increased. Secondly, a process has been developed for the fabrication of stable, well-characterized, and reproducible Josephson devices based on resistively-shunted Nb and NbN tunnel junctions. The devices utilize submicron-area, high current-density tunnel junctions and a AuGe shunt resistor to yield completely non-hysteretic I-V curves, normal-state resistances of about [...] products of about half a millivolt. These devices should be nearly optimal for mixing at [...]. Heterodyne measurements using these junctions have been performed in a waveguide mixer mount. Receiver temperatures as low as 190 K (DSB), with -6 dB conversion efficiency, have been obtained at 100 [...], but these results are still a factor of about four higher than those predicted by the RSJ simulations. Accurate measurements of the available noise power of the junctions at the intermediate frequency of 1.5 [...] were made, and confirmed that the receivers were limited by elevated junction output noise. The deviations of the noise from theoretical predictions are shown to be caused by the nonlinear interaction of the junction with the embedding circuit. While this work points out some of the complexity introduced by the strong nonlinearity of Josephson devices, it is still expected that Josephson-effect mixers may be useful for heterodyne detection at very high frequencies.
We performed spectral measurements of a large niobium Josephson junctions array. The array consists of 9996 serially connected Nb/NbSi/Nb junctions placed on a 1×1 cm silicon substrate. The spectrum was analyzed by a heterodyne superconducting receiver based on a high-TcJosephson mixer. It was discovered that the linewidth of Josephson radiation is strongly influenced by configuration and type of a measurement system. We obtain the linewidth down to 0.2 MHz when connecting the array to an autonomous power source and minimizing technical noise. We also observed the shift of the spectral frequency from the Josephson one that can be explained by peculiarities of synchronization of such large multi-oscillator systems.