Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal de Physique IV (Proceedings)

Processing of DC SQUIDs for radiofrequency amplification

R. Chicault, M. C. Cyrille, Y. Berthier, J.C. Villégier, Florence Pourtier, H. Moriceau, S. Nicoletti

Published Jun 1, 1994• 2 citations
Publisher

Abstract

The goal of this studies is to use dc Squids as low noise radiofrequency amplifier (Tn ≈1K) in the frequency range 1-150 Mhz and to integrate them in NMR probe. DC Squids have been built using planar technology and with two types of superconducting materials : low Tc(Nb) and High Tc(YBa2Cu3O7). Contrary to the traditional set up used in magnetometry (flux locked loop) the dc Squid is here fluxed biased near Φz=(2n+1)Φo/4 and no flux locked loop is connected. Small variations of flux (Φs<<Φo) introduced from signal source via the input coil are amplified following the transfer characteristic VΦ=dV/dΦ. The low Tc devices are set up to now the best, concerning the reproducibility and the qualities of the Josephson Junctions obtained with a three layer process Nb/Al-Al2O3/Nb. Such junctions have been realized following the so called SNOP process, without anodization. The main characteristic obtained at 4.2K are RJ/RN=10, 2Δ≈2.8 meV and a Josephson current density J≈103 A/cm2. The high Tc devices have been built with bi-epitaxial YBa2Cu3O7 junctions and with a 30x30µm2 area loop. I(V) and V(Φ) characteristics curves obtained are promizing for applications as RF detection in the temperature range : 4-77K. Modelization studies are currently in progress for the optimization of those devices (low Tc and high Tc) as RF amplifiers (minimization of parasitic capacitance between the input coil and the Squid loop) in order to increase their upper frequency limit.\n* This work is partially supported by Ultimatech (CNRS), by the "région Rhône-Alpes" and E.E.C. "HTSC-GBJ" programs n°7100.

DOI
10.1051/jp4:1994642

Related papers

Broadband SQUID amplifiers for photonic applications

Vladimir Polushkin, D. Glowacka, R. Hart +1 more

The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•1 citation

Low noise DC SQUIDs fabricated in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology

M. B. Ketchen, Manjul Bhushan, Steven B. Kaplan +1 more

The authors have designed, fabricated and tested all-refractory DC SQUIDs in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology that have noise performance comparable to the best previously reported for any technology. A variety of SQUID designs were incorporated as part of a trilayer process development test vehicle. SQUID inductance, junction area, and resistive shunt geometry were varied in matrix fashion to give SQUIDs with near-optimum parameter values for a factor of five range in Josephson current density and shunt sheet resistance. The devices were fabricated using a selective niobium anodization with a minimum feature size of 2 mu m. The base electrode and Nb wiring were patterned with dry etching, and the junction areas were defined by anodization: the Ti resistors were patterned with a lift-off process. Current density on different wafers was varied from 400 to 1000 A/cm/sup 2/ with typical junction V/sub m/'s of 60 mV. The shunt sheet resistance was varied in the 1-5- Omega / Square Operator range. The noise was measured with an RF SQUID direct small-signal readout scheme. A 50-pH SQUID with 3- mu m/sup 2/, 16- mu A junctions and 14- Omega shunt resistors was shown to have an ideally low white noise of 1*10/sup -13/ Phi /sub 0//sup 2//Hz, a white to 1/f crossover frequency at 7 Hz, and a noise level less than 6*10/sup -12/ Phi /sub 0//sup 2//Hz at 0.1 Hz.

IEEE Transactions on Magnetics•Mar 1, 1991•25 citations

Very low noise, tightly coupled, dc SQUID amplifiers

B. Muhlfelder, J. A. Beall, Michael W. Cromar +1 more

We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.

Applied Physics Letters•Oct 27, 1986•19 citations

Low-noise ultra-high-speed dc SQUID readout electronics

D. Drung, Colmar Hinnrichs, H.-J. Barthelmess

User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.

Superconductor Science and Technology•Feb 27, 2006•76 citations

Review of low-noise radio-frequency amplifiers based on superconducting quantum interference device

Y.H. Lee, Yonuk Chong, Yannis Kyriakos Semertzidis

Superconducting quantum interference device (SQUID) is a sensitive detector of magnetic flux signals. Up to now, the main application of SQUIDs has been measurements of magnetic flux signals in the frequency range from near DC to several MHz. Recently, cryogenic low-noise radio-frequency (RF) amplifiers based on DC SQUID are under development aiming to detect RF signals with sensitivity approaching quantum limit. In this paper, we review the recent progress of cryogenic low-noise RF amplifiers based on SQUID technology.

Progress in Superconductivity and Cryogenics•Dec 31, 2014•0 citations

Array of Superconducting Quantum Interference Devices with Multiturn Input Coil

T. Morooka, Hiroaki Myoren, S. Takada +1 more

Arrays of dc-superconducting quantum interference devices (dc-SQUIDs) were investigated, in which each dc-SQUID element has a multiturn input coil. The dependence of flux noise on the number of turns of the input coil was studied for current amplifiers. SQUID arrays were fabricated by a Nb/AlO x /Nb Josephson tunnel junction fabrication process. Results show that the flux noise of the SQUID array amplifier does not depend on the turn number of the input coil. A SQUID array amplifier consisting of 128 dc-SQUID elements was fabricated, in which each element had a 7-turn input coil and a mutual inductance between the input coil and the SQUID loop of 460 pH. This amplifier showed an ultrahigh current resolution of 1 pA/Hz0.5 and a maximum input current of 11 µA for signals of 50 kHz, which is sufficient bandwidth for X-ray detection applications. These values correspond to a large dynamic range of 87 dB. The flux-voltage characteristics of this SQUID array, however, showed asymmetric behavior, which originated from electronic resonance in stray capacitance and the mutual inductance between the SQUID loop and the multiturn input coil.

Japanese Journal of Applied Physics•May 1, 2004•3 citations
The goal of this studies is to use dc Squids as low noise radiofrequency amplifier (Tn ≈1K) in the frequency range 1-150 Mhz and to integrate them in NMR probe. DC Squids have been built using planar technology and with two types of superconducting materials : low Tc(Nb) and High Tc(YBa2Cu3O7). Contrary to the traditional set up used in magnetometry (flux locked loop) the dc Squid is here fluxed biased near Φz=(2n+1)Φo/4 and no flux locked loop is connected. Small variations of flux (Φs<<Φo) introduced from signal source via the input coil are amplified following the transfer characteristic VΦ=dV/dΦ. The low Tc devices are set up to now the best, concerning the reproducibility and the qualities of the Josephson Junctions obtained with a three layer process Nb/Al-Al2O3/Nb. Such junctions have been realized following the so called SNOP process, without anodization. The main characteristic obtained at 4.2K are RJ/RN=10, 2Δ≈2.8 meV and a Josephson current density J≈103 A/cm2. The high Tc devices have been built with bi-epitaxial YBa2Cu3O7 junctions and with a 30x30µm2 area loop. I(V) and V(Φ) characteristics curves obtained are promizing for applications as RF detection in the temperature range : 4-77K. Modelization studies are currently in progress for the optimization of those devices (low Tc and high Tc) as RF amplifiers (minimization of parasitic capacitance between the input coil and the Squid loop) in order to increase their upper frequency limit.\n* This work is partially supported by Ultimatech (CNRS), by the "région Rhône-Alpes" and E.E.C. "HTSC-GBJ" programs n°7100.
The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.
The authors have designed, fabricated and tested all-refractory DC SQUIDs in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology that have noise performance comparable to the best previously reported for any technology. A variety of SQUID designs were incorporated as part of a trilayer process development test vehicle. SQUID inductance, junction area, and resistive shunt geometry were varied in matrix fashion to give SQUIDs with near-optimum parameter values for a factor of five range in Josephson current density and shunt sheet resistance. The devices were fabricated using a selective niobium anodization with a minimum feature size of 2 mu m. The base electrode and Nb wiring were patterned with dry etching, and the junction areas were defined by anodization: the Ti resistors were patterned with a lift-off process. Current density on different wafers was varied from 400 to 1000 A/cm/sup 2/ with typical junction V/sub m/'s of 60 mV. The shunt sheet resistance was varied in the 1-5- Omega / Square Operator range. The noise was measured with an RF SQUID direct small-signal readout scheme. A 50-pH SQUID with 3- mu m/sup 2/, 16- mu A junctions and 14- Omega shunt resistors was shown to have an ideally low white noise of 1*10/sup -13/ Phi /sub 0//sup 2//Hz, a white to 1/f crossover frequency at 7 Hz, and a noise level less than 6*10/sup -12/ Phi /sub 0//sup 2//Hz at 0.1 Hz.
We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.
User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.
Superconducting quantum interference device (SQUID) is a sensitive detector of magnetic flux signals. Up to now, the main application of SQUIDs has been measurements of magnetic flux signals in the frequency range from near DC to several MHz. Recently, cryogenic low-noise radio-frequency (RF) amplifiers based on DC SQUID are under development aiming to detect RF signals with sensitivity approaching quantum limit. In this paper, we review the recent progress of cryogenic low-noise RF amplifiers based on SQUID technology.
Arrays of dc-superconducting quantum interference devices (dc-SQUIDs) were investigated, in which each dc-SQUID element has a multiturn input coil. The dependence of flux noise on the number of turns of the input coil was studied for current amplifiers. SQUID arrays were fabricated by a Nb/AlO x /Nb Josephson tunnel junction fabrication process. Results show that the flux noise of the SQUID array amplifier does not depend on the turn number of the input coil. A SQUID array amplifier consisting of 128 dc-SQUID elements was fabricated, in which each element had a 7-turn input coil and a mutual inductance between the input coil and the SQUID loop of 460 pH. This amplifier showed an ultrahigh current resolution of 1 pA/Hz0.5 and a maximum input current of 11 µA for signals of 50 kHz, which is sufficient bandwidth for X-ray detection applications. These values correspond to a large dynamic range of 87 dB. The flux-voltage characteristics of this SQUID array, however, showed asymmetric behavior, which originated from electronic resonance in stray capacitance and the mutual inductance between the SQUID loop and the multiturn input coil.