Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physica B+C

High current-density Josephson edge-junction capacitance

David F. Moore, P. Vettiger, Theo Forster

Published Aug 1, 1981• 8 citations
Publisher
DOI
10.1016/0378-4363(81)90795-6

Related papers

Current dependence of the low bias resistance of small capacitance Josephson junctions

Venkat Chandrasekhar

arXiv:2404.05890•Physics Letters A•Apr 10, 2024•3 citations

An ultra-small capacitance Josephson junction

Efrat Shimshoni, Yuval Gefen, Shimon Levit

•Jan 1, 1989•0 citations

Fabrication of ultrasmall Nb-AlOx-Nb Josephson tunnel junctions

John M. Martinis, Ronald H. Ono

We describe a fabrication process to make Nb-AlOx-Nb edge junctions with areas as small as 0.0022 μm2 and with current densities from 10 to 24 000 A/cm2. The junction conductance was low for voltages below the superconducting energy gap which indicates good quality tunnel barriers. Coulomb gap measurements obtained when the junctions were in the normal state were used to find the junction capacitance. Junction capacitance as small as 0.18 fF has been measured.

Applied Physics Letters•Aug 6, 1990•34 citations

A high-temperature superconductor latching driver operated at 30 K for a single-flux-quantum/semiconductor interface

Tsunehiro Hato, Masahiro Horibe, Naoki Harada +5 more

We report on a latching-type driver operated at 30 K for the output interface of single-flux-quantum (SFQ) circuits. Ramp-edge-type high-temperature superconductor (HTS) junctions showed only small inherent hysteresis in current–voltage characteristics at a temperature of 30 K. To have hysteresis large enough for latching operation, we chose La-doped YbBaCuO as a counter electrode of an interface modified junction, and used amorphous LaSrAlTaO to form an additional barrier to the interface modified barrier. The junction shunted with optimized capacitance showed sufficiently large hysteresis of 33%, which is as large as that of a non-shunted junction at 4.2 K. We employed 20 kA cm−2 as the critical current density (Jc) of the junction to fabricate dc/SFQ, Josephson transmission lines (JTLs) and the latching driver on the same chip. It is smaller than the optimum current density that gives the smallest punchthrough probability of the junction, which was calculated to be 10−12 for a 30 Gbps ac bias by using the junction parameters at 30 K. However, the probability for Jc of 20 kA cm−2 is still smaller than that of low-temperature semiconductor junctions because of the larger Jc of the HTS junctions. The fabricated latching driver successfully converted the SFQ pulse, which passed through several JTLs from the dc/SFQ circuit, to a 1 mV level signal at 30 K.

Superconductor Science and Technology•Nov 7, 2003•3 citations

Ground Capacitance in Josephson Junction Arrays

Zlatko Minev, Ioan M. Pop, Nicholas A. Masluk +2 more

Bulletin of the American Physical Society•Feb 28, 2012•0 citations

Logic Operation of HTS SFQ Logic Family

Koji Tsubone, Y. Tarutani, H. Wakana +2 more

A high-Tcsuperconducting (HTS) single-flux-quantum (SFQ) logic family including an and gate, an or gate, and an inverter was designed. The circuit parameters were optimized for a Josephson junction's critical current density, which may change due to a temperature change or insufficient run-to-run reproducibility of the fabrication process. New circuit design layout rules were implemented to improve Icx uniformity. As a result, all circuits were successfully tested and show at least plusmn40% critical current density operational margins. An effect of the parasitic capacitance formed by a junction electrode and a ground plane on the operating margins of the and gate was investigated by numerical simulation. Test circuits were fabricated using YBa2Cu3O7-deltaramp-edge junction technology and were operated at temperatures higher than 30 K. Bias current margins were also measured, and they found to be close to the simulated ones.

IEEE Transactions on Applied Superconductivity•Jul 15, 2009•2 citations
We report on a latching-type driver operated at 30 K for the output interface of single-flux-quantum (SFQ) circuits. Ramp-edge-type high-temperature superconductor (HTS) junctions showed only small inherent hysteresis in current–voltage characteristics at a temperature of 30 K. To have hysteresis large enough for latching operation, we chose La-doped YbBaCuO as a counter electrode of an interface modified junction, and used amorphous LaSrAlTaO to form an additional barrier to the interface modified barrier. The junction shunted with optimized capacitance showed sufficiently large hysteresis of 33%, which is as large as that of a non-shunted junction at 4.2 K. We employed 20 kA cm−2 as the critical current density (Jc) of the junction to fabricate dc/SFQ, Josephson transmission lines (JTLs) and the latching driver on the same chip. It is smaller than the optimum current density that gives the smallest punchthrough probability of the junction, which was calculated to be 10−12 for a 30 Gbps ac bias by using the junction parameters at 30 K. However, the probability for Jc of 20 kA cm−2 is still smaller than that of low-temperature semiconductor junctions because of the larger Jc of the HTS junctions. The fabricated latching driver successfully converted the SFQ pulse, which passed through several JTLs from the dc/SFQ circuit, to a 1 mV level signal at 30 K.
A high-Tcsuperconducting (HTS) single-flux-quantum (SFQ) logic family including an and gate, an or gate, and an inverter was designed. The circuit parameters were optimized for a Josephson junction's critical current density, which may change due to a temperature change or insufficient run-to-run reproducibility of the fabrication process. New circuit design layout rules were implemented to improve Icx uniformity. As a result, all circuits were successfully tested and show at least plusmn40% critical current density operational margins. An effect of the parasitic capacitance formed by a junction electrode and a ground plane on the operating margins of the and gate was investigated by numerical simulation. Test circuits were fabricated using YBa2Cu3O7-deltaramp-edge junction technology and were operated at temperatures higher than 30 K. Bias current margins were also measured, and they found to be close to the simulated ones.