Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Experimental study of amplitude–frequency characteristics of high-transition-temperature radio frequency superconducting quantum interference devices

Xian-Lin Zeng, Y. Zhang, Boris Chesca, K. Barthel, Ya. S. Greenberg, Alex I. Braginski

Published Dec 1, 2000• 14 citations
Publisher

Abstract

We measured the amplitude–frequency characteristics of radio frequency superconducting quantum interference devices (rf SQUIDs) over a temperature range between 65 and 79 K. Using the expressions derived from the recently developed rf SQUID theory, valid also at large thermal fluctuations, we determined from these data the basic parameters of high-transition-temperature superconductor (HTS) rf SQUIDs. These parameters were: (a) the high-frequency coupling coefficient between the rf SQUID and the tank circuit resonator, k, (b) the SQUIDs hysteretic parameter, β, (c) the critical current of the Josephson junction, Ic, (d) its normal resistance, Rn, and (e) its noise parameter, Γ. We found a good agreement with the values of β(Ic) and Rn determined directly after destructively opening the SQUID loop. In accordance with the theoretical predictions, our experimental results show that at large thermal fluctuation levels (T≅77 K), rf SQUIDs with large loop inductance operate in nonhysteretic mode up to β values exceeding 3. Furthermore, we have shown that the optimal energy sensitivity is attained in the nonhysteretic mode at a value of β distinctly higher than 1. A quantitative comparison of white noise predicted by the theory with that obtained from the experiment showed a reasonable agreement. We also discussed the contribution of the phase information to the SQUID’s signal and noise at optimum operation conditions, when a mixer was used as a signal detector.

DOI
10.1063/1.1288780

Related papers

Inductance mode characteristics of a ceramic YBa2Cu3O7−x radio-frequency superconducting quantum interference device at 77 K

Evgeni V. Il’ichev, A. V. Andreev, Christian S. Jacobsen

Experimental results on some radio-frequency superconducting quantum interference device (rf-SQUID) signal properties are presented. The quantum interferometer was made of ceramic YBa2Cu3O7−x and was due to a low critical current operated in the inductance or nonhysteretic mode. With bias current as reference, amplitude variation, and phase shift of the voltage over the tank circuit coupled to the SQUID were measured simultaneously. It is shown that there is qualitative agreement between calculations based on the resistivity shunted junction model and the data. Moreover, using phase detection, signal instabilities predicted for the rf-SQUID inductance mode were observed. These signal instabilities may be exploited to enhance the transfer coefficient for measured flux-to-output signal.

Journal of Applied Physics•Sep 1, 1993•1 citation

Impedance of radio-frequency-biased resistive superconducting quantum interference devices

Robert J. Soulen, Deborah van Vechten

We have measured with high accuracy (100 ppm) and high precision (5--10 ppm) the impedance of a rf-driven resistive superconducting quantum interference device (SQUID) as a function of the amplitude and frequency of the radio-frequency (rf) bias, as a function of the current bias, and as a function of several other circuit parameters. We have developed the coupled differential equations for the resistive SQUID and for the rf tank circuit. The fit of the solutions of these equations to the data for nonhysteretic junctions is excellent. We were unable to develop solutions for the hysteretic case and thus simply present examples of typical data obtained in order to illustrate the differences with the nonhysteretic case. The relationship of this study to noise thermometry using resistive SQUID's is indicated.

Physical review. B, Condensed matter•Jul 1, 1987•13 citations

Analysis of the current-voltage characteristic of the rf SQUID

Philippe Lethuillier

The electrical equations of a resonant circuit fed with a radio-frequency current and inductively coupled to a weakly superconducting loop have been derived. The current-voltage characteristic of the rf superconducting quantum interference device can then be calculated and studied as a function of the junction resistance or of the resonance frequency, enabling its behavior to be better understood. As shown by Kurkijärvi, the large positive slope of the steps and the rounding of the characteristic result from thermal noise. However, in order to explain quantitatively the experimental results concerning, namely, point contact weak links which are generally oxidized or which have several contact points, it is useful to remark that the connection between the two superconductors constituting the Josephson junction may be made from n resistive paths. The mean thermal energy of the fluctuating flux is then close to nkbT instead of kbT if the inductances linking the contact points are large enough, that is, on the order of 10−11 H.

Journal of Applied Physics•Jun 1, 1993•0 citations

Transfer function and thermal noise of YBa2Cu3O7−δ direct current superconducting quantum interference devices operated under large thermal fluctuations

K. Barthel, D. Koelle, Boris Chesca +4 more

Direct current superconducting quantum interference devices (SQUIDs) made from high transition temperature superconductors typically exhibit a still unexplained higher white noise and smaller transfer function than numerical simulations based on the coupled Langevin equations predict. We present a systematic study that compares experimental results with both numerical simulations and a recently developed analytical approach based on a Fokker–Planck equation. To cover a wide range of SQUID parameters, two samples of different inductances were measured at variable temperature. While several predictions of the analytical theory could be verified and a good qualitative agreement with both theories is observed, only one sample showed good quantitative agreement. Furthermore, our simulations performed in the limit of large thermal fluctuations show excellent agreement with the analytic theory.

Applied Physics Letters•Apr 12, 1999•10 citations

A method for determining the SQUID parameter β and the coupling coefficient K in a nonhysteretic rf SQUID

Sergio Nicola Erne, Holger M. Luther

A method for determining the superconducting-quantum-interference-device (SQUID) parameter β = LsIc/Φo and the coupling coefficient K between the SQUID loop and tank circuit based on the general theory for the nonhysteretic rf SQUID is derived. Analysis of the periodic dependence of the amplitude of the tank-circuit voltage on applied dc flux leads to explicit expressions for β and K. Important advantages of the method are that, during measurements, the SQUID loop has neither to be opened nor decoupled from the tank circuit, and the temperature of the sample does not have to be changed. Measurements with a Nb-point-contact SQUID at 4.2 K to verify the method in practice are reported. Intrinsic errors were estimated to be less than 10%.

Journal of Applied Physics•Apr 1, 1981•3 citations

Operation of high-temperature rf SQUID magnetometers using dielectric SrTiO3 resonators

Y. Zhang, M. Gottschlich, Helmut Soltner +4 more

The operation of YBa2Cu3O7 rf superconducting quantum interference devices (SQUIDs) using a dielectric SrTiO3 resonator as tank circuit was tested. At 77 K, we attained for such resonators unloaded quality factors Q0 up to 7000 at resonant frequencies near 1 GHz, when measuring without electromagnetic shielding. For a washer SQUID with an area of 4×4 mm2 and an inductance of ≂100 pH, which was properly coupled to the resonator, we measured an approximately 60 μV peak-to-peak SQUID signal and a white flux noise spectral density of SΦ1/2=1×10−5Φ0/√Hz, corresponding to a field sensitivity of BN=105 fT/√Hz. With an additional single-layer flux transformer with a diameter of the pickup loop of 22 mm in flip-chip arrangement, the field sensitivity was improved to 30 fT/√Hz.

Applied Physics Letters•Nov 20, 1995•16 citations
We measured the amplitude–frequency characteristics of radio frequency superconducting quantum interference devices (rf SQUIDs) over a temperature range between 65 and 79 K. Using the expressions derived from the recently developed rf SQUID theory, valid also at large thermal fluctuations, we determined from these data the basic parameters of high-transition-temperature superconductor (HTS) rf SQUIDs. These parameters were: (a) the high-frequency coupling coefficient between the rf SQUID and the tank circuit resonator, k, (b) the SQUIDs hysteretic parameter, β, (c) the critical current of the Josephson junction, Ic, (d) its normal resistance, Rn, and (e) its noise parameter, Γ. We found a good agreement with the values of β(Ic) and Rn determined directly after destructively opening the SQUID loop. In accordance with the theoretical predictions, our experimental results show that at large thermal fluctuation levels (T≅77 K), rf SQUIDs with large loop inductance operate in nonhysteretic mode up to β values exceeding 3. Furthermore, we have shown that the optimal energy sensitivity is attained in the nonhysteretic mode at a value of β distinctly higher than 1. A quantitative comparison of white noise predicted by the theory with that obtained from the experiment showed a reasonable agreement. We also discussed the contribution of the phase information to the SQUID’s signal and noise at optimum operation conditions, when a mixer was used as a signal detector.
Experimental results on some radio-frequency superconducting quantum interference device (rf-SQUID) signal properties are presented. The quantum interferometer was made of ceramic YBa2Cu3O7−x and was due to a low critical current operated in the inductance or nonhysteretic mode. With bias current as reference, amplitude variation, and phase shift of the voltage over the tank circuit coupled to the SQUID were measured simultaneously. It is shown that there is qualitative agreement between calculations based on the resistivity shunted junction model and the data. Moreover, using phase detection, signal instabilities predicted for the rf-SQUID inductance mode were observed. These signal instabilities may be exploited to enhance the transfer coefficient for measured flux-to-output signal.
We have measured with high accuracy (100 ppm) and high precision (5--10 ppm) the impedance of a rf-driven resistive superconducting quantum interference device (SQUID) as a function of the amplitude and frequency of the radio-frequency (rf) bias, as a function of the current bias, and as a function of several other circuit parameters. We have developed the coupled differential equations for the resistive SQUID and for the rf tank circuit. The fit of the solutions of these equations to the data for nonhysteretic junctions is excellent. We were unable to develop solutions for the hysteretic case and thus simply present examples of typical data obtained in order to illustrate the differences with the nonhysteretic case. The relationship of this study to noise thermometry using resistive SQUID's is indicated.
The electrical equations of a resonant circuit fed with a radio-frequency current and inductively coupled to a weakly superconducting loop have been derived. The current-voltage characteristic of the rf superconducting quantum interference device can then be calculated and studied as a function of the junction resistance or of the resonance frequency, enabling its behavior to be better understood. As shown by Kurkijärvi, the large positive slope of the steps and the rounding of the characteristic result from thermal noise. However, in order to explain quantitatively the experimental results concerning, namely, point contact weak links which are generally oxidized or which have several contact points, it is useful to remark that the connection between the two superconductors constituting the Josephson junction may be made from n resistive paths. The mean thermal energy of the fluctuating flux is then close to nkbT instead of kbT if the inductances linking the contact points are large enough, that is, on the order of 10−11 H.
Direct current superconducting quantum interference devices (SQUIDs) made from high transition temperature superconductors typically exhibit a still unexplained higher white noise and smaller transfer function than numerical simulations based on the coupled Langevin equations predict. We present a systematic study that compares experimental results with both numerical simulations and a recently developed analytical approach based on a Fokker–Planck equation. To cover a wide range of SQUID parameters, two samples of different inductances were measured at variable temperature. While several predictions of the analytical theory could be verified and a good qualitative agreement with both theories is observed, only one sample showed good quantitative agreement. Furthermore, our simulations performed in the limit of large thermal fluctuations show excellent agreement with the analytic theory.
A method for determining the superconducting-quantum-interference-device (SQUID) parameter β = LsIc/Φo and the coupling coefficient K between the SQUID loop and tank circuit based on the general theory for the nonhysteretic rf SQUID is derived. Analysis of the periodic dependence of the amplitude of the tank-circuit voltage on applied dc flux leads to explicit expressions for β and K. Important advantages of the method are that, during measurements, the SQUID loop has neither to be opened nor decoupled from the tank circuit, and the temperature of the sample does not have to be changed. Measurements with a Nb-point-contact SQUID at 4.2 K to verify the method in practice are reported. Intrinsic errors were estimated to be less than 10%.
The operation of YBa2Cu3O7 rf superconducting quantum interference devices (SQUIDs) using a dielectric SrTiO3 resonator as tank circuit was tested. At 77 K, we attained for such resonators unloaded quality factors Q0 up to 7000 at resonant frequencies near 1 GHz, when measuring without electromagnetic shielding. For a washer SQUID with an area of 4×4 mm2 and an inductance of ≂100 pH, which was properly coupled to the resonator, we measured an approximately 60 μV peak-to-peak SQUID signal and a white flux noise spectral density of SΦ1/2=1×10−5Φ0/√Hz, corresponding to a field sensitivity of BN=105 fT/√Hz. With an additional single-layer flux transformer with a diameter of the pickup loop of 22 mm in flip-chip arrangement, the field sensitivity was improved to 30 fT/√Hz.