Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

Optically bistable scheme with multiple lateral feedbacks

Vyacheslav A. Trofimov, Andrey Shobukhov

Published Nov 18, 2003• 0 citations
Publisher

Abstract

We study an optically bistable scheme based on increasing absorption and equipped with multiple lateral feedbacks. These loops appear as a result of partial feeding of the output beam back into the semiconductor crystal through its side surface perpendicularly to the input beam. The cases of one-photon and two-photon absorption are considered. Using the mathematical model of the device we demonstrate bistability and compare two possibilities of switching from one steady state to another. We propose a technique which allows approximately fivefold reduction of the switching time and a decrease of energy consumption as compared with the existing devices based only on the increasing absorption.

DOI
10.1117/12.528060

Related papers

An optically bistable absorption scheme with additional lateral feedback loops

Vyacheslav A. Trofimov, Andrey Shobukhov

An optically bistable absorption system involving several feedback loops formed by the lateral supply of a fraction of light energy passed through a semiconductor with single-and two-photon absorption is analyzed. It is shown that multistability can be realized in the case of two-photon absorption. The use of several loops makes it possible to significantly reduce energy expenditures on switching and to reduce the switching time by approximately a factor of 10. A method of switching the system from one state to another by varying the reflectivities of side mirrors is proposed.

Optics and Spectroscopy•Apr 1, 2003•1 citation

Absorption optical bistable scheme with additional lateral feedback

Vyacheslav A. Trofimov, Andrey Shobukhov, A. S. Makarik

We consider an optically bistable scheme based on growing absorption and equipped with an additional lateral feedback loop. Mathematical model of this device is proposed and analyzed. We demonstrate the simultaneous transfer to instability of steady states that belong to upper and lower branches of the bistable media characteristic curve. This stability loss may cause either self-switching of the scheme from one steady state to another or generation of autooscillations. The latter may be used for the formation of pulse sequences with given duration. We show that adding several loops instead of one sufficiently decreases the input intensity, necessary for switching. The role of diffusion processes in pulse formation is discussed, and the spatially non-uniformal stationary solutions are demonstrated.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Sep 24, 1999•0 citations

Optical bistability due to increasing absorption

David A. B. Miller, Arthur C. Gossard, W. Wiegmann

It is shown theoretically that optical bistability will exist in a material whose optical absorption is more than linearly proportional to the degree to which the material is excited. No cavity or external feedback is required. The underlying principle of this bistability appears to be a generalization of several previous independent discussions of mirrorless bistabilities in specific physical systems. This bistability and associated differential gain are demonstrated experimentally using a thermal nonlinearity in a GaAs/GaAlAs multiple-quantum-well semiconductor. Theory and experiment show good agreement.

Optics Letters•May 1, 1984•100 citations

Two-wavelength switching with a distributed-feedback semiconductor optical amplifier (DFBSOA)

Antonio Hurtado, Ana Pilar Gonzalez-Marcos, José A. Martín-Pereda +1 more

Switching of a signal beam by another control beam at different wavelength is demonstrated experimentally using the optical bistability occurring in a 1.55 µm-distributed feedback semiconductor optical amplifier (DFBSOA) working in reflection. Counterclockwise (S-shaped) and reverse (clockwise) bistability are observed in the output of the control and the signal beam respectively, as the power of the input control signal is increased. With this technique an optical signal can be set in either of the optical input wavelengths by appropriate choice of the powers of the input signals. The switching properties of the DFBSOA are studied experimentally as the applied bias current is increased from below to above threshold and for different levels of optical power in the signal beam and different wavelength detunings between both input signals. Higher on-off extinction ratios, wider bistable loops and lower input power requirements for switching are obtained when the DFBSOA is operated slightly above its threshold value.

IEE Proceedings - Optoelectronics•Jan 25, 2006•20 citations

Optical bistable devices as sensing elements

Ana Pilar Gonzalez-Marcos, Antonio Hurtado, José A. Martín-Pereda

The nonlinear optical properties of many materials and devices have been the main object of research as potential candidates for sensing in different places. Just one of these properties has been, in most of the cases, the basis for the sensing operation. As a consequence, just one parameter can be detected. In this paper, although just one property will be employed too, we will show the possibility to sense different parameters with just one type of sensor. The way adopted in this work is the use of the optical bistability obtained from different photonic structures. Because this optical bistability has a strong dependence on many different parameters the possibility to sense different inputs appears. In our case, we will report the use of some non-linear optical devices, mainly Semiconductor Optical Amplifiers, as sensing elements. Because their outputs depend on many parameters, as the incident light wavelength, polarization, intensity and direction, applied voltage and feedback characteristics, they can be employed to detect, at the same time, different type of signals. This is because the way these different signals affect to the sensor response is very different too and appears under a different set of characteristics.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 30, 2004•5 citations

Optical bistability in active distributed—feedback structures: an experimental and theoretical study

Richard R. Wyatt, Mike J. Adams

Optical bistability in active semiconductor devices has attracted considerable interest recently due to the possibility of combining microwatt switching powers with nanosecond switching times. We present experimental and theoretical results of optical bistability in a distributed-feedback (DFB) laser amplifier operating in reflection at 1.5 μm; switch-on delay followed by a sharp transient overshoot is predicted and observed. Minimum switching energies are in the femtojoule region.

Conference on Lasers and Electro-Optics•Jan 1, 1986•4 citations
We study an optically bistable scheme based on increasing absorption and equipped with multiple lateral feedbacks. These loops appear as a result of partial feeding of the output beam back into the semiconductor crystal through its side surface perpendicularly to the input beam. The cases of one-photon and two-photon absorption are considered. Using the mathematical model of the device we demonstrate bistability and compare two possibilities of switching from one steady state to another. We propose a technique which allows approximately fivefold reduction of the switching time and a decrease of energy consumption as compared with the existing devices based only on the increasing absorption.
An optically bistable absorption system involving several feedback loops formed by the lateral supply of a fraction of light energy passed through a semiconductor with single-and two-photon absorption is analyzed. It is shown that multistability can be realized in the case of two-photon absorption. The use of several loops makes it possible to significantly reduce energy expenditures on switching and to reduce the switching time by approximately a factor of 10. A method of switching the system from one state to another by varying the reflectivities of side mirrors is proposed.
We consider an optically bistable scheme based on growing absorption and equipped with an additional lateral feedback loop. Mathematical model of this device is proposed and analyzed. We demonstrate the simultaneous transfer to instability of steady states that belong to upper and lower branches of the bistable media characteristic curve. This stability loss may cause either self-switching of the scheme from one steady state to another or generation of autooscillations. The latter may be used for the formation of pulse sequences with given duration. We show that adding several loops instead of one sufficiently decreases the input intensity, necessary for switching. The role of diffusion processes in pulse formation is discussed, and the spatially non-uniformal stationary solutions are demonstrated.
It is shown theoretically that optical bistability will exist in a material whose optical absorption is more than linearly proportional to the degree to which the material is excited. No cavity or external feedback is required. The underlying principle of this bistability appears to be a generalization of several previous independent discussions of mirrorless bistabilities in specific physical systems. This bistability and associated differential gain are demonstrated experimentally using a thermal nonlinearity in a GaAs/GaAlAs multiple-quantum-well semiconductor. Theory and experiment show good agreement.
Switching of a signal beam by another control beam at different wavelength is demonstrated experimentally using the optical bistability occurring in a 1.55 µm-distributed feedback semiconductor optical amplifier (DFBSOA) working in reflection. Counterclockwise (S-shaped) and reverse (clockwise) bistability are observed in the output of the control and the signal beam respectively, as the power of the input control signal is increased. With this technique an optical signal can be set in either of the optical input wavelengths by appropriate choice of the powers of the input signals. The switching properties of the DFBSOA are studied experimentally as the applied bias current is increased from below to above threshold and for different levels of optical power in the signal beam and different wavelength detunings between both input signals. Higher on-off extinction ratios, wider bistable loops and lower input power requirements for switching are obtained when the DFBSOA is operated slightly above its threshold value.
The nonlinear optical properties of many materials and devices have been the main object of research as potential candidates for sensing in different places. Just one of these properties has been, in most of the cases, the basis for the sensing operation. As a consequence, just one parameter can be detected. In this paper, although just one property will be employed too, we will show the possibility to sense different parameters with just one type of sensor. The way adopted in this work is the use of the optical bistability obtained from different photonic structures. Because this optical bistability has a strong dependence on many different parameters the possibility to sense different inputs appears. In our case, we will report the use of some non-linear optical devices, mainly Semiconductor Optical Amplifiers, as sensing elements. Because their outputs depend on many parameters, as the incident light wavelength, polarization, intensity and direction, applied voltage and feedback characteristics, they can be employed to detect, at the same time, different type of signals. This is because the way these different signals affect to the sensor response is very different too and appears under a different set of characteristics.