Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Electronics Letters

Measurement of optical bistability in an InGaAsP laser amplifier at 1.5 μm

H.J. Westlake, M.J. Adams, M.J. O’Mahony

Published Oct 10, 1985• 53 citations
Publisher

Abstract

Measured hysteresis characteristics for an amplifier operating at room temperature are presented and compared with the predictions of a computer model. The onset of optical bistability was seen to occur at input powers of around 2 μW.
DOI
10.1049/el:19850701

Related papers

Room-temperature optical bistability in InGaAsP/InP amplifiers and implications for passive devices

Wayne F. Sharfin, M. Dagenais

Optical bistability has been observed for the first time in a room-temperature InGaAsP/InP amplifier. Switching occurred at an optical input power of about 3 μW, corresponding to a change in the refractive index of 5×10−4. The results are discussed in terms of a light-induced change in carrier concentration. Implications for bistability in passive devices are also discussed.

Applied Physics Letters•May 1, 1985•54 citations

Optical Bistability in 1.55 μm Semiconductor Laser Amplifiers

M.J. Adams, H.J. Westlake, M.J. O’Mahony

Dispersive bistability arising from the carrier-dependence of the refractive index has been observed in semiconductor lasers operated just below threshold with a small injected optical signal. The minimum optical input required for switch-up is as low as 1 μW for InGaAsP amplifiers at 1.55 μm(1) and 1.3 μm(2) (cf 30 μW for GaAs devices(3)). As yet, reliable measurements of the dynamic response are not (4) available, although we predict recovery times to be on the order of carrier lifetimes, ie a few nanoseconds at room temperature. This contribution will review our experimental and theoretical work on 1.55 μm amplifier bistability and set it in the context of other semiconductor bistable optical devices.

Topical Meeting on Optical Bistability (OB)•Jan 1, 1985•0 citations

Measurements and modeling of reflective bistability in 1.55-μm laser diode amplifiers

Paradorn Pakdeevanich, M.J. Adams

We present experimental measurements of bistable characteristics for the case of a 1.55-/spl mu/m symmetric Fabry-Perot laser amplifier with a particularly rich variety of behavior for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical output-input characteristic when the drive current or initial phase detuning is changed. A "butterfly" hysteresis loop is observed experimentally at an optical input power as low as 300 /spl mu/W for a drive current equal to 94% of the lasing threshold. The dependence of the reflective optical bistability on drive current, initial phase detuning, and injected optical pewter has been investigated for the first time in an uncoated 1.55-/spl mu/m amplifier. Measurements of the device voltage shifts on switching reveal hysteresis loops which match those in the corresponding optical powers and which indicate the amount of gain saturation and nonlinear refraction responsible for bistability. An analytical model is used to describe the observed reflective bistability and to give insight into the detailed physical mechanisms responsible.

IEEE Journal of Quantum Electronics•Jan 1, 1999•44 citations

Optical bistability in InGaAsP amplifiers and implications for passive devices

Wayne F. Sharfin, M. Dagenais

We demonstrate optically bistable (light switching light) operation in a room-temperature InGaAsP Fabry-Perot amplifier. The amplifier is an InGaAsP/InP laser structure biased at ~95% of its lasing threshold. It is switched with <3 μW of optical power provided by the mechanically chopped output of a quasi-single-mode InGaAsP/InP laser. The experimental apparatus is depicted in Fig, 1. A change in the refractive Index in the amplifier of only 5 × 10−4 is sufficient to cause switching. Input and output pulses from the nonlinear amplifier are shown in Fig. 2 when the source frequency is initially detuned by 14 GHz from the closest Fabry-Perot mode of the amplifier. Smaller switching powers are required at lesser detunings. The physical mechanism of the intensity-dependent change of the refractive index is thought to be the change in carrier density resulting from stimulated recombination of free carriers.

Conference on Lasers and Electro-Optics•Jan 1, 1985•0 citations

Optical bistability in distributed feedback semiconductor laser amplifiers

M.J. Adams, Richard R. Wyatt

New theoretical and experimental results are presented for optical bistability in distributed feedback amplifiers at 1.5 μm. The onset of bistability occurs at input powers as low as 1 μW, a factor of about 1000 times less than the input predicted for passive DFB structures. The transient response exhibits a large spike as the amplifier goes through a resonance, in good agreement with the theoretical prediction.

IEE Proceedings J Optoelectronics•Jan 1, 1987•37 citations

Optical bistability measurements on a 1.S- μm semiconductor laser amplifier

H.J. Westlake, Matthew Adams, M.J. O’Mahony

Optical bistability in semiconductor laser amplifiers is particularly interesting because of the gain provided by the device. Small changes, in input power can result in large changes in amplifier gain, and this leads to possible applications in all-optical regenerators for transmission systems. Other possible applications include their use as optical switches and logic elements.1 Optical bistability in GaAs laser amplifiers operating at 850 nm has been reported previously.2 Here we report for the first time measured results at 1.5 μm with an InGaAsP device.

Conference on Lasers and Electro-Optics•Jan 1, 1985•0 citations
Dispersive bistability arising from the carrier-dependence of the refractive index has been observed in semiconductor lasers operated just below threshold with a small injected optical signal. The minimum optical input required for switch-up is as low as 1 μW for InGaAsP amplifiers at 1.55 μm(1) and 1.3 μm(2) (cf 30 μW for GaAs devices(3)). As yet, reliable measurements of the dynamic response are not (4) available, although we predict recovery times to be on the order of carrier lifetimes, ie a few nanoseconds at room temperature. This contribution will review our experimental and theoretical work on 1.55 μm amplifier bistability and set it in the context of other semiconductor bistable optical devices.
We present experimental measurements of bistable characteristics for the case of a 1.55-/spl mu/m symmetric Fabry-Perot laser amplifier with a particularly rich variety of behavior for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical output-input characteristic when the drive current or initial phase detuning is changed. A "butterfly" hysteresis loop is observed experimentally at an optical input power as low as 300 /spl mu/W for a drive current equal to 94% of the lasing threshold. The dependence of the reflective optical bistability on drive current, initial phase detuning, and injected optical pewter has been investigated for the first time in an uncoated 1.55-/spl mu/m amplifier. Measurements of the device voltage shifts on switching reveal hysteresis loops which match those in the corresponding optical powers and which indicate the amount of gain saturation and nonlinear refraction responsible for bistability. An analytical model is used to describe the observed reflective bistability and to give insight into the detailed physical mechanisms responsible.
We demonstrate optically bistable (light switching light) operation in a room-temperature InGaAsP Fabry-Perot amplifier. The amplifier is an InGaAsP/InP laser structure biased at ~95% of its lasing threshold. It is switched with <3 μW of optical power provided by the mechanically chopped output of a quasi-single-mode InGaAsP/InP laser. The experimental apparatus is depicted in Fig, 1. A change in the refractive Index in the amplifier of only 5 × 10−4 is sufficient to cause switching. Input and output pulses from the nonlinear amplifier are shown in Fig. 2 when the source frequency is initially detuned by 14 GHz from the closest Fabry-Perot mode of the amplifier. Smaller switching powers are required at lesser detunings. The physical mechanism of the intensity-dependent change of the refractive index is thought to be the change in carrier density resulting from stimulated recombination of free carriers.
Optical bistability in semiconductor laser amplifiers is particularly interesting because of the gain provided by the device. Small changes, in input power can result in large changes in amplifier gain, and this leads to possible applications in all-optical regenerators for transmission systems. Other possible applications include their use as optical switches and logic elements.1 Optical bistability in GaAs laser amplifiers operating at 850 nm has been reported previously.2 Here we report for the first time measured results at 1.5 μm with an InGaAsP device.