Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

ac Josephson effect in superconducting all-Nb thin-film nanobridges up to 693 GHz

Yoshinori Uzawa, Etsuo Kawate, Nobumitsu Hirose, Isao Motohashi, Y. Harada, Matsuo Sekine, Yukinobu Miki, Masahiro Okaji

Published Aug 24, 1992• 3 citations
Publisher

Abstract

All-niobium thin-film nanobridges were fabricated with bridge sizes of 40-nm length, 50-nm width, and 100-nm thickness. We investigated the performance of the nanobridges by monitoring Shapiro steps induced on the current-voltage curves by an optically pumped far-infrared laser. These steps have been observed up to 693 GHz (433 μm). This is a twofold increase over that previously reported on thin-film nanobridges.

DOI
10.1063/1.108472

Related papers

Fabrication of Niobium Nanobridge Josephson Junctions

Takashi Tachiki, Kenji Horiguchi, Takashi Uchida

To realize antenna-coupled Josephson detectors for microwave and millimeter-wave radiation, planar-type Nb nanobridge Josephson junctions were fabricated. Nb thin films whose thickness, the root mean square roughness and the critical temperature were 20.0 nm, 0.109 nm and 8.4 K, respectively were deposited using a DC magnetron sputtering at a substrate temperature of 700°C. Nanobridges were obtained from the film using 80-kV electron beam lithography and reactive ion-beam etching in CF 4 (90%) + O2 (10%) gases. The minimum bridge area was 65 nm wide and 60 nm long. For the nanobridge whose width and length were less than 110 nm, an I-V characteristic showed resistively-shunted-junction behaviour near the critical temperature. Moreover, Shapiro steps were observed in the nanobridge with microwave irradiation at a frequency of 6 – 30 GHz. The Nb nanobridges can be used as detectors in the antenna-coupled devices.

Journal of Physics Conference Series•May 12, 2014•2 citations

AC Josephson effect in superconducting niobium nitride tunnel junctions at up to 2.5 THz

M. C. Wicks, P R Haycocks, T. Hori

Shapiro steps have been observed in the I–V characteristics of an NbN tunnel junction illuminated with radiation from an optically pumped far infrared laser. The maximum operating frequency which produced an observable Shapiro step was 2.53 THz. This is a four-fold increase over that previously reported for a thin film Josephson junction. Clear steps were also produced by various laser lines in the frequency range 0.6–1.8 THz.

Electronics Letters•Apr 26, 1990•4 citations

Niobium dc SQUIDs with Nanobridge Junctions

E.E. Mitchell, S. K. H. Lam

DC SQUIDs with outer loop size ∼10 μmx 10 μm have been fabricated with nanobridge Josephson junctions in thin Niobium films (25, 100 and 200 nm) using either electron beam or focused ion beam techniques. Such SQUIDs are ideally suited to incorporate into the centre strip of a superconducting coplanar waveguide. The current-voltage characteristics and magnetic field modulation of the SQUIDs are compared for the two methods. The temperature dependence of the critical current is quite linear for the e-beam devices whilst the focused ion beam devices fit an exponential. Here we also investigate trimming methods to reduce the critical currents of the nanojunctions fabricated in the thicker films, in order to improve the SQUID parameters at lower temperatures.

Physics Procedia•Jan 1, 2012•10 citations

Submillimeter-Wave Response of Nb-YBaCuO Point-Contact Josephson Junctions Using YBaCuO Thin Films Prepared by CVD

Syozo Imai, Nobuhiro Sugawara, Kazushige Sumiya +6 more

The Shapiro steps in the submillimeter wave (SMMW) region were measured in point-contact Josephson junctions made of a Nb strip with a sharpened edge and a YBaCuO thin film. The thin film was prepared by the chemical vapor deposition (CVD) method. The dependence of the Shapiro step width on the SMMW power was measured for the wavelength of 570.6 µm (525.4 GHz). The dependence was similar to that found in microbridges made of low T c superconductors. The first-order Shapiro step was observed for the wavelength of 232.9 µm (1.287 THz).

Japanese Journal of Applied Physics•Oct 1, 1990•2 citations

High frequency properties of all-NbN nanobridges with gap structure in I-V curves

K. Hamasaki, Tsuyoshi Yakihara, Z. Wang +2 more

All-NbN nanobridges with gap structure in I-V curves have been reproducibly constructed using RIE and lift-off techniques. The nanobridges had a width of 2 μm, and a thickness ofcRNproducts of ∼3 mV, and low excess current. Small-area dc SQUIDs were made using the nanobridges, and analyses of the response to magnetic flux were performed. The current-phase relationship of the nano-bridges was found to be close to sinusoidal. The maximum LC resonant voltage was about 1.2 mV, corresponding to a frequency of 580 GHz. The IF peak was obtained up to the bias voltage of about 4 mV in 101 GHz Josephson mixing.

IEEE Transactions on Magnetics•Mar 1, 1987•15 citations

Dry Etching of Nb and Fabrication of Nb Variable-Thickness-Bridges

Takeshi Harada, Kenji Gamo, Susumu Namba

Several reactive dry etching methods; ion etching, sputter etching and plasma etching, were studied in order to fabricate a niobium variable-thickness type thin film bridge (VTB). Niobium was etched by CF4 reactive sputter etching with submicron accuracy and no significant influence on the superconducting transition temperature except very near the surface (<200 Å). The niobium VTB behaved as an S-S'-S bridge, and a reduced self-heating effect was realized by a variable-thickness geometry. The DC Josephson effect was observed in the temperature range without thermal hysteresis. The quality factor of the I c R n product obtained was at least 0.42 mV.

Japanese Journal of Applied Physics•Jan 1, 1981•27 citations
All-niobium thin-film nanobridges were fabricated with bridge sizes of 40-nm length, 50-nm width, and 100-nm thickness. We investigated the performance of the nanobridges by monitoring Shapiro steps induced on the current-voltage curves by an optically pumped far-infrared laser. These steps have been observed up to 693 GHz (433 μm). This is a twofold increase over that previously reported on thin-film nanobridges.
To realize antenna-coupled Josephson detectors for microwave and millimeter-wave radiation, planar-type Nb nanobridge Josephson junctions were fabricated. Nb thin films whose thickness, the root mean square roughness and the critical temperature were 20.0 nm, 0.109 nm and 8.4 K, respectively were deposited using a DC magnetron sputtering at a substrate temperature of 700°C. Nanobridges were obtained from the film using 80-kV electron beam lithography and reactive ion-beam etching in CF 4 (90%) + O2 (10%) gases. The minimum bridge area was 65 nm wide and 60 nm long. For the nanobridge whose width and length were less than 110 nm, an I-V characteristic showed resistively-shunted-junction behaviour near the critical temperature. Moreover, Shapiro steps were observed in the nanobridge with microwave irradiation at a frequency of 6 – 30 GHz. The Nb nanobridges can be used as detectors in the antenna-coupled devices.
DC SQUIDs with outer loop size ∼10 μmx 10 μm have been fabricated with nanobridge Josephson junctions in thin Niobium films (25, 100 and 200 nm) using either electron beam or focused ion beam techniques. Such SQUIDs are ideally suited to incorporate into the centre strip of a superconducting coplanar waveguide. The current-voltage characteristics and magnetic field modulation of the SQUIDs are compared for the two methods. The temperature dependence of the critical current is quite linear for the e-beam devices whilst the focused ion beam devices fit an exponential. Here we also investigate trimming methods to reduce the critical currents of the nanojunctions fabricated in the thicker films, in order to improve the SQUID parameters at lower temperatures.
The Shapiro steps in the submillimeter wave (SMMW) region were measured in point-contact Josephson junctions made of a Nb strip with a sharpened edge and a YBaCuO thin film. The thin film was prepared by the chemical vapor deposition (CVD) method. The dependence of the Shapiro step width on the SMMW power was measured for the wavelength of 570.6 µm (525.4 GHz). The dependence was similar to that found in microbridges made of low T c superconductors. The first-order Shapiro step was observed for the wavelength of 232.9 µm (1.287 THz).
All-NbN nanobridges with gap structure in I-V curves have been reproducibly constructed using RIE and lift-off techniques. The nanobridges had a width of 2 μm, and a thickness ofcRNproducts of ∼3 mV, and low excess current. Small-area dc SQUIDs were made using the nanobridges, and analyses of the response to magnetic flux were performed. The current-phase relationship of the nano-bridges was found to be close to sinusoidal. The maximum LC resonant voltage was about 1.2 mV, corresponding to a frequency of 580 GHz. The IF peak was obtained up to the bias voltage of about 4 mV in 101 GHz Josephson mixing.
Several reactive dry etching methods; ion etching, sputter etching and plasma etching, were studied in order to fabricate a niobium variable-thickness type thin film bridge (VTB). Niobium was etched by CF4 reactive sputter etching with submicron accuracy and no significant influence on the superconducting transition temperature except very near the surface (<200 Å). The niobium VTB behaved as an S-S'-S bridge, and a reduced self-heating effect was realized by a variable-thickness geometry. The DC Josephson effect was observed in the temperature range without thermal hysteresis. The quality factor of the I c R n product obtained was at least 0.42 mV.