Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE International Symposium on Information Theory (ISIT)

Design of high-rate irregular non-binary LDPC codes using algorithmic stopping-set cancellation

Sudarsan V. S. Ranganathan, D. Divsalar, Kasra Vakilinia, Richard D. Wesel

Published Jun 1, 2014• 7 citations
Publisher

Abstract

Following Poulliat et al.'s design of (2, dc) nonbinary LDPC (NB-LDPC) codes, this paper designs high-rate irregular NB-LDPC codes by addressing the problem of minimum symbol distance. The design procedure first identifies all stopping sets up to weight five in an LDPC code and enumerates them via a message passing algorithm. For each identified stopping set, careful labeling forces its corresponding parity-check sub-matrix to be full rank, thereby preventing the stopping set from being a sub-code and ensuring a minimum distance of at least six symbols. Simulation results for codes designed through this procedure show a significant improvement in the error-floor region over randomized labeling.

DOI
10.1109/isit.2014.6874925

Related papers

Design of Nonbinary LDPC Codes Based on Message-Passing Algorithms

Sunghye Cho, Kyungwhoon Cheun, Kyeongcheol Yang

Short cycles in a nonbinary low-density parity-check (NB-LDPC) code may be even more harmful to its performance if they do not satisfy the so-called full rank condition (FRC). This is because they may induce low-weight codewords or absorbing sets in that case. Thus, it is important to count the number of short cycles not satisfying the FRC as well as the number of short cycles for analyzing the performance of an NB-LDPC code. In this paper, we first develop a novel message-passing algorithm and identify how it is related to the FRC. We then propose a low-complexity algorithm for counting the number of short cycles not satisfying the FRC in an NB-LDPC code, as well as the number of short cycles. Finally, we propose a low-complexity algorithm for designing an NB-LDPC code with low error floor. Depending on the modulation scheme, the codes constructed by the proposed design algorithm have similar or slightly worse performance, compared with those constructed via the method by Poulliat et al. However, the proposed design algorithm does not require a cycle enumeration algorithm with high complexity, and therefore is feasible even in the case of large code length, say ≥5000.

IEEE Transactions on Communications•Jun 19, 2018•6 citations

An Iterative Scheme of Stopping Set Enlargement in The Design of Short-Length Irregular LDPC Codes

Jingyu Kang, Pingyi Fan, Zhigang Cao

Abstract: Small stopping sets have been proved to be harmful to the error floor performance of a finite-length irregular low-density parity-check (LDPC) code over the binary erasure channel (BEC). On the additive white gaussian noise (AWGN) channel, small stopping sets are expected to have a similar effect. This paper proposes an algorithm that iteratively removes the small-stopping-set-inducing patterns from the graph of a randomly generated irregular LDPC code by means of node exchange, aiming at enlarging the average size of stopping sets in this code. Computer simulation results show that the short-length LDPC codes after our processing achieve a considerable performance improvement in the low-BER region compared to the randomly generated codes. Key words: Error floor, irregular LDPC codes, iterative processing, small stopping set 1

•Jan 1, 2005•1 citation

On a Construction Method of Irregular LDPC Codes Without Small Stopping Sets

Gerd Richter, Axel Hof

In this paper, we present a construction method based on the progressive edge-growth (PEG) algorithm to design irregular low-density parity-check (LDPC) codes without small stopping sets. We show how to choose the connections in the PEG algorithm when having multiple choices to connect a variable node with a check node. Since preventing small stopping sets also prevents a low minimum distance, our construction method also leads to LDPC codes with a higher minimum distance. Furthermore, we show by simulation that our construction method improves the performance over the binary erasure channel and over the additive white Gaussian noise channel for a low erasure probability and a high signal-to-noise ratio, respectively.

International Conference on Communications•Jan 1, 2006•38 citations

Finite-length and asymptotic analysis and design of LDPC codes for binary erasure and fading channels.

Kaiann Fu

Low-density parity-check (LDPC) codes in conjunction with iterative decoding based on message-passing algorithms have been shown to achieve excellent performance over a variety of communication channels. In this dissertation, we investigate LDPC codes under two scenarios which present different challenges for providing robust communications. First, LDPC codes are analyzed and designed for time-selective, frequency-nonselective complex-fading channels where both the amplitude and the phase of the transmitted signal are altered by the channel. To combat the fading, we use a pilot symbol-assisted scheme where known pilot symbols are added to the LDPC code and used to help estimate the channel at the receiver. Using asymptotic, infinite-length analysis, we investigate several iterative, message-passing, joint-estimation-and-decoding strategies; optimal energy distribution between pilot and data symbols; and LDPC code design. Several interesting results are obtained regarding unification of analysis and code design. Next, we address the issue of achieving very low error rates with practical, finite-length LDPC codes for binary erasure channels. Finite-length LDPC codes suffer from error floors which limit the achievable error rate, and this error-floor performance is determined by stopping sets. Asymptotic analysis of weight and stopping-set enumerators, for codewords and stopping sets which grow linearly with codelength, has aided in designing codes with lower error floors but does not reflect the behavior of sublinearly-sized stopping sets, which can dominate the iterative-decoding, error-floor performance. Thus, we provide a perspective on protograph-based and standard LDPC ensemble enumerators, based on analysis of stopping sets with sublinear growth, which brings new insight into sublinear stopping-set behavior, advantages of protograph structure, and effects of precoding. We show for stopping sets that grow at most logarithmically with codelength, the enumerators follow a polynomial relationship with codelength, unlike the exponential relationship for linearly-growing stopping sets, and this polynomial relationship can be approximately captured by a single parameter. Further, we begin to address the question, Given finite stopping-set sizes and finite codelengths, do the stopping sets follow the behavior predicted by linear or sublinear analysis?

•Jan 1, 2007•1 citation

Design of Low-Density Parity-Check Codes and Their Decoding Algorithms

조성혜

In this thesis, we propose low-complexity designing algorithms for non-binary low-density \nparity-check (NB-LDPC) codes over GF(q) with low error floor and low-complexity decoding \nalgorithms for binary LDPC codes. \nWe first propose a low-complexity designing algorithm for for NB-LDPC codes over GF(q) \nbased on message-passing algorithms. Short cycles in an NB-LDPC code may be even \nmore harmful to its performance if they do not satisfy the so-called full rank condition \n(FRC). This is because they may induce low-weight codewords or absorbing sets in that \ncase. Thus, it is crucial to count the number of short cycles not satisfying the FRC as well as \nthe number of short cycles for analyzing the performance of an NB-LDPC code. In order to \ncount those cycles, we first develop a novel message-passing algorithm and identify how it \nis related to the FRC.We then propose a low-complexity algorithmfor counting the number \nof short cycles not satisfying the FRC in an NB-LDPC code, as well as the number of short \ncycles. The proposed algorithm is not only theoretically validated, but its computational \nand storage complexities are also computed. It does not require cycle enumeration with \nhigh complexity, and therefore is still feasible even in the case of large code length, say \n≤ 5000, unlike the conventional methods. Based on it, we also provide a locally optimal \nrule to choose a nonzero element for a given edge and propose a low-complexity algorithm \nfor designing an NB-LDPC code with low error floor. Furthermore, several design examples \nare presented to verify the validity of the proposed design algorithm. \nSecondly, we propose a low-complexity decoding algorithm for binary LDPC codes over \nthe binary symmetric channel (BSC). The min-sum (MS) algorithm is a low-complexity decoding \nalgorithm for binary LDPC codes and has lower computational complexity than the \nsum-product algorithm (SPA). Since the MS algorithm is an approximation of the SPA, it \nhas performance degradation. Furthermore, reducing the number of bits for representing \nmessages to two in a decoding algorithm for further reducing computational and storage \ncomplexities, causes significant performance losses. In order to minimize the performance \ndegradation and computational and storage complexities, we propose a low-complexity \ndecoding algorithm which uses several decoders with two-bit precision for binary LDPC \ncodes over the BSC. The proposed algorithm adaptively changes decoders according to \nthe number of unsatisfied check nodes at each iteration. Compared with the SPA using \nfloating-point operations, the proposed decoding algorithm greatly reduces computational \nand storage complexities with negligible performance losses. Numerical results show that \nthe proposed decoding algorithm has similar performance to the SPA with floating-point \noperations over the BSC. \nIn the last part of this thesis, low-complexity decoding algorithms of binary LDPC codes \nfor the core layer at fixed receivers in ATSC 3.0 are proposed. Gallager’s decoding algorithms \nB (GDB) and E (GDE) for binary LDPC codes have much lower computational \ncomplexity and much less required memory size than the SPA. This is because GDB and \nGDE only use binary or integer operations, while the SPA requires real operations and \na look-up table. However, they are hardly used in commercial communication systems \nsince they have poorer performance than the SPA. Layered-division multiplexing (LDM) \nis considered in ATSC 3.0 in order to deliver multiple broadcasting streams with distinct \nrobustness in a single radio frequency channel. Due to the unique characteristic of the \nLDM, we propose to use GDB or GDE rather than the SPA for decoding the core layer signal \nat fixed receivers. Numerical results show that the computational complexity and the \nrequired memory size can be reduced without any performance loss by about 50 percent \nand 80 percent, respectively, when GDB and GDE are employed.

•Jan 1, 2018•0 citations

Eliminating small stopping sets in irregular low-density parity-check codes

Xiaopeng Jiao, Jianjun Mu, Jing Song +1 more

We present a novel scheme to eliminate small stopping sets in irregular low-density parity-check (LDPC) codes. By adding several new check nodes and having their edges connected to small stopping sets in the original code, the improved code decreases the number of small stopping sets efficiently. Simulation results show that the proposed scheme decreases the frame error rate (FER) significantly in the error floor region, whereas having almost the same rate as the original code.

IEEE Communications Letters•Jun 1, 2009•22 citations
Following Poulliat et al.'s design of (2, dc) nonbinary LDPC (NB-LDPC) codes, this paper designs high-rate irregular NB-LDPC codes by addressing the problem of minimum symbol distance. The design procedure first identifies all stopping sets up to weight five in an LDPC code and enumerates them via a message passing algorithm. For each identified stopping set, careful labeling forces its corresponding parity-check sub-matrix to be full rank, thereby preventing the stopping set from being a sub-code and ensuring a minimum distance of at least six symbols. Simulation results for codes designed through this procedure show a significant improvement in the error-floor region over randomized labeling.
Short cycles in a nonbinary low-density parity-check (NB-LDPC) code may be even more harmful to its performance if they do not satisfy the so-called full rank condition (FRC). This is because they may induce low-weight codewords or absorbing sets in that case. Thus, it is important to count the number of short cycles not satisfying the FRC as well as the number of short cycles for analyzing the performance of an NB-LDPC code. In this paper, we first develop a novel message-passing algorithm and identify how it is related to the FRC. We then propose a low-complexity algorithm for counting the number of short cycles not satisfying the FRC in an NB-LDPC code, as well as the number of short cycles. Finally, we propose a low-complexity algorithm for designing an NB-LDPC code with low error floor. Depending on the modulation scheme, the codes constructed by the proposed design algorithm have similar or slightly worse performance, compared with those constructed via the method by Poulliat et al. However, the proposed design algorithm does not require a cycle enumeration algorithm with high complexity, and therefore is feasible even in the case of large code length, say ≥5000.
Abstract: Small stopping sets have been proved to be harmful to the error floor performance of a finite-length irregular low-density parity-check (LDPC) code over the binary erasure channel (BEC). On the additive white gaussian noise (AWGN) channel, small stopping sets are expected to have a similar effect. This paper proposes an algorithm that iteratively removes the small-stopping-set-inducing patterns from the graph of a randomly generated irregular LDPC code by means of node exchange, aiming at enlarging the average size of stopping sets in this code. Computer simulation results show that the short-length LDPC codes after our processing achieve a considerable performance improvement in the low-BER region compared to the randomly generated codes. Key words: Error floor, irregular LDPC codes, iterative processing, small stopping set 1
In this paper, we present a construction method based on the progressive edge-growth (PEG) algorithm to design irregular low-density parity-check (LDPC) codes without small stopping sets. We show how to choose the connections in the PEG algorithm when having multiple choices to connect a variable node with a check node. Since preventing small stopping sets also prevents a low minimum distance, our construction method also leads to LDPC codes with a higher minimum distance. Furthermore, we show by simulation that our construction method improves the performance over the binary erasure channel and over the additive white Gaussian noise channel for a low erasure probability and a high signal-to-noise ratio, respectively.
Low-density parity-check (LDPC) codes in conjunction with iterative decoding based on message-passing algorithms have been shown to achieve excellent performance over a variety of communication channels. In this dissertation, we investigate LDPC codes under two scenarios which present different challenges for providing robust communications. First, LDPC codes are analyzed and designed for time-selective, frequency-nonselective complex-fading channels where both the amplitude and the phase of the transmitted signal are altered by the channel. To combat the fading, we use a pilot symbol-assisted scheme where known pilot symbols are added to the LDPC code and used to help estimate the channel at the receiver. Using asymptotic, infinite-length analysis, we investigate several iterative, message-passing, joint-estimation-and-decoding strategies; optimal energy distribution between pilot and data symbols; and LDPC code design. Several interesting results are obtained regarding unification of analysis and code design. Next, we address the issue of achieving very low error rates with practical, finite-length LDPC codes for binary erasure channels. Finite-length LDPC codes suffer from error floors which limit the achievable error rate, and this error-floor performance is determined by stopping sets. Asymptotic analysis of weight and stopping-set enumerators, for codewords and stopping sets which grow linearly with codelength, has aided in designing codes with lower error floors but does not reflect the behavior of sublinearly-sized stopping sets, which can dominate the iterative-decoding, error-floor performance. Thus, we provide a perspective on protograph-based and standard LDPC ensemble enumerators, based on analysis of stopping sets with sublinear growth, which brings new insight into sublinear stopping-set behavior, advantages of protograph structure, and effects of precoding. We show for stopping sets that grow at most logarithmically with codelength, the enumerators follow a polynomial relationship with codelength, unlike the exponential relationship for linearly-growing stopping sets, and this polynomial relationship can be approximately captured by a single parameter. Further, we begin to address the question, Given finite stopping-set sizes and finite codelengths, do the stopping sets follow the behavior predicted by linear or sublinear analysis?
In this thesis, we propose low-complexity designing algorithms for non-binary low-density \nparity-check (NB-LDPC) codes over GF(q) with low error floor and low-complexity decoding \nalgorithms for binary LDPC codes. \nWe first propose a low-complexity designing algorithm for for NB-LDPC codes over GF(q) \nbased on message-passing algorithms. Short cycles in an NB-LDPC code may be even \nmore harmful to its performance if they do not satisfy the so-called full rank condition \n(FRC). This is because they may induce low-weight codewords or absorbing sets in that \ncase. Thus, it is crucial to count the number of short cycles not satisfying the FRC as well as \nthe number of short cycles for analyzing the performance of an NB-LDPC code. In order to \ncount those cycles, we first develop a novel message-passing algorithm and identify how it \nis related to the FRC.We then propose a low-complexity algorithmfor counting the number \nof short cycles not satisfying the FRC in an NB-LDPC code, as well as the number of short \ncycles. The proposed algorithm is not only theoretically validated, but its computational \nand storage complexities are also computed. It does not require cycle enumeration with \nhigh complexity, and therefore is still feasible even in the case of large code length, say \n≤ 5000, unlike the conventional methods. Based on it, we also provide a locally optimal \nrule to choose a nonzero element for a given edge and propose a low-complexity algorithm \nfor designing an NB-LDPC code with low error floor. Furthermore, several design examples \nare presented to verify the validity of the proposed design algorithm. \nSecondly, we propose a low-complexity decoding algorithm for binary LDPC codes over \nthe binary symmetric channel (BSC). The min-sum (MS) algorithm is a low-complexity decoding \nalgorithm for binary LDPC codes and has lower computational complexity than the \nsum-product algorithm (SPA). Since the MS algorithm is an approximation of the SPA, it \nhas performance degradation. Furthermore, reducing the number of bits for representing \nmessages to two in a decoding algorithm for further reducing computational and storage \ncomplexities, causes significant performance losses. In order to minimize the performance \ndegradation and computational and storage complexities, we propose a low-complexity \ndecoding algorithm which uses several decoders with two-bit precision for binary LDPC \ncodes over the BSC. The proposed algorithm adaptively changes decoders according to \nthe number of unsatisfied check nodes at each iteration. Compared with the SPA using \nfloating-point operations, the proposed decoding algorithm greatly reduces computational \nand storage complexities with negligible performance losses. Numerical results show that \nthe proposed decoding algorithm has similar performance to the SPA with floating-point \noperations over the BSC. \nIn the last part of this thesis, low-complexity decoding algorithms of binary LDPC codes \nfor the core layer at fixed receivers in ATSC 3.0 are proposed. Gallager’s decoding algorithms \nB (GDB) and E (GDE) for binary LDPC codes have much lower computational \ncomplexity and much less required memory size than the SPA. This is because GDB and \nGDE only use binary or integer operations, while the SPA requires real operations and \na look-up table. However, they are hardly used in commercial communication systems \nsince they have poorer performance than the SPA. Layered-division multiplexing (LDM) \nis considered in ATSC 3.0 in order to deliver multiple broadcasting streams with distinct \nrobustness in a single radio frequency channel. Due to the unique characteristic of the \nLDM, we propose to use GDB or GDE rather than the SPA for decoding the core layer signal \nat fixed receivers. Numerical results show that the computational complexity and the \nrequired memory size can be reduced without any performance loss by about 50 percent \nand 80 percent, respectively, when GDB and GDE are employed.