Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Spectroscopy

Sub-Doppler Spectral Resolution and Improved Sensitivity in a Cesium Resonance Fluorescence Imaging Monochromator

Nathan C. Pixley, Tiffany L. Correll, Dimitri Pappas, Benjamin W. Smith, James D. Winefordner

Published Jun 1, 2002• 10 citations
Publisher

Abstract

Improvements in spectral resolution and sensitivity of a cesium based resonance fluorescence imaging monochromator (RFIM) are described. Alignment of the two lasers used in the excitation scheme in a co-propagating geometry have resulted in a detector spectral bandpass (270 MHz) that is narrower than the Doppler broadened profile (380 MHz) of cesium vapor at room temperature. Improvements in the experimental design, namely the addition of an image intensifier and cooled charge-coupled device (CCD) camera, have resulted in increased sensitivity; we report a limit of detection of 10 8 photons per pixel limited by image intensifier noise. Images of the cesium D 2 line emission (852.12 nm) from a cesium hollow cathode lamp were compared to an argon emission line (4Sº 1/2 → 4P 3/2 ) at 852.14 nm from a silver/argon hollow cathode lamp as a demonstration of the spectral resolution. The ability of the RFIM to discriminate between photons exciting the F = 4 vs. F = 3 ground state hyperfine level (a frequency difference of 9.2 GHz) of the cesium 6 2 S 1/2 state was also investigated to further demonstrate the spectral selectivity. The potential use of the described RFIM for chemical imaging applications is discussed.

DOI
10.1366/000370202760076910

Related papers

Tunable resonance fluorescence monochromator with sub-Doppler spectral resolution

Nathan C. Pixley, Tiffany L. Correll, Dimitri Pappas +3 more

A cesium-based resonance fluorescence monochromator with a spectral resolution of 200 MHz and a tunable response over the D(2) absorption line of cesium (380 MHz) is described. The narrow spectral response is achieved through excitation of a monokinetic population of the 6(2)P(3/2)( degrees ) state by arrangement of the excitation lasers in either a copropagating or a counterpropagating orientation. The narrow spectral response of the detector allows for excitation of specific hyperfine components involved in the 6(2)P(3/2)( degrees ) (F=3-5) to 6(2)D(5/2) (F=2-6) transition (917.23 nm). The selectivity gained through resolving specific hyperfine transitions allows for a photon detector that is both spectrally tunable and narrow. We report the sub-Doppler linewidths achieved through various laser beam orientations. We also describe how these beam geometries can be applied to spectrally narrow and tunable image detection.

Optics Letters•Dec 15, 2001•15 citations

Spectrally selective optical pumping in Doppler-broadened cesium atoms

Jun-Hai Zhang, Xianjin Zeng, Qing-Meng Li +2 more

The D1 line spectrally selective pumping process in Doppler-broadened cesium is analyzed by solving the optical Bloch equations. The process, described by a three-level model with the Λ scheme, shows that the saturation intensity of broadened atoms is three orders of magnitude larger than that of resting atoms. The |Fg = 3〉 → |Fe = 4〉 resonance pumping can result in the ground state |Fg = 4, mF = 4〉 sublevel having a maximum population of 0.157 and the population difference would be about 0.01 in two adjacent magnetic sublevels of the hyperfine (HF) state Fg = 4. To enhance the anisotropy in the ground state, we suggest employing dichromatic optical HF pumping by adding a laser to excite D1 line |Fg = 4〉 → |Fe = 3〉 transition, in which the cesium magnetometer sensitivity increases by half a magnitude and is unaffected by the nonlinear Zeeman effect even in Earth's average magnetic field.

Chinese Physics B•May 1, 2013•2 citations

Measurement of the fine structure of cesium Rydberg state

Dong-Liang Pei, Jun He, Jieying Wang +2 more

The spectra of Rydberg atoms are of great significance for studying the energy levels of Rydberg atoms and the interaction between neutral atoms, especially, the high-precision spectra of Rydberg atoms can be used to measure the energy level shifts of Rydberg atoms resulting from the dipole-dipole interactions in room-temperature vapor cells. In this paper we report the preparation of cesium Rydberg states based on the cascaded two-photon excitation of 509 nm laser and 852 nm laser in opposite, and the measurements of the fine structure of cesium Rydberg states. In this experiment, the 509 nm laser is generated by the cavity-enhanced second-harmonic generation from 1018 nm laser with a periodically-poled KTP crystal and has a maximum power of about 1 W, and the 852 nm probe laser is provided by an external-cavity diode laser with a maximum output power of 5 mW and a typical linewidth of 1 MHz. By scanning the frequency of 509 nm coupling laser, it is presented that the Doppler-free spectra based on electromagnetically-induced transparency (EIT) of 509 nm coupling laser and 852 nm probe laser. The velocity-selective EIT spectra are used to study the spectral splitting of 6S1/26P3/257S(D) ladder-type system of cesium Rydberg atoms in a room-temperature vapor cell. The powers of 852 nm probe laser and 509 nm coupling laser are 0.3 upW and 200 mW, respectively. Their waist radii are both approximately 50 m. The intervals of hyperfine splitting of the intermediate state 6P3/2(F'=3, 4, 5) and fine splitting of 57D3/2 and 57D5/2 Rydberg states are measured by a frequency calibrating. Concretely, the velocity-selective spectrum with a radio frequency (RF) modulation of 30 MHz is used as a reference to calibrate the Rydberg fine-structure states in the hot vapor cell, where the RF frequency precision is smaller than a hertz on long time scales and the EIT linewidth is smaller than 13 MHz. The experimental value of the fine structure splitting of 57D3/2 and 57D5/2 Rydberg states is (354.72.5) MHz, that is in consistence with the value of 346.8 MHz calculated by Rydberg-Ritz equation and quantum defects of 57D3/2 and 57D5/2 Rydberg states. The experimental values of hyperfine splitting of intermediate state 6P3/2(F'=3, 4, 5) are also coincident with the theoretical calculated values. The dominant discrepancy existing between the experimental and calculated results may arise from the nonlinear correspondence of the PZT while the 509 nm wavelength cavity is scanned, and the measurement accuracy influenced by the spectral linewidth. The velocity-selective spectroscopy technique can also be used to measure the energy level shifts caused by the interactions of Rydberg atoms.

Acta Physica Sinica•Jan 1, 2017•6 citations

Visualization of radio-frequency waves via double resonance spectroscopy of cesium atoms

Moto Kinoshita, Masanori Ishii

Abstract A novel technique to visualize RF waves in the gigahertz frequency range based on the double resonance spectroscopy of cesium-133 atoms is developed. This technique allows one to obtain fluorescence at a near-infrared wavelength of 852 nm, which can be detected by a charge-coupled device camera. The fluorescence depends on the strength distribution of 9.2 GHz RF waves. This method realizes real-time, high-resolution imaging using RF waves. In this study, the visualization of RF waves on a microstrip line is demonstrated and RF standing waves are clearly observed. The sensitivity of the visualization to the input power and phase shift of the RF standing waves arising from a particular condition of the reflection waves are investigated.

Japanese Journal of Applied Physics•Mar 18, 2019•7 citations

Saturation effects in the sub-Doppler spectroscopy of cesium vapor confined in an extremely thin cell

C. Andreeva, S. Cartaleva, L. Petrov +5 more

Saturation effects affecting absorption and fluorescence spectra of an atomic vapor confined in an extremely thin cell (cell thickness $L<1\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{m}$) are investigated experimentally and theoretically. The study is performed on the ${D}_{2}$ line $(\ensuremath{\lambda}=852\phantom{\rule{0.3em}{0ex}}\mathrm{nm})$ of Cs and concentrates on the two situations $L=\ensuremath{\lambda}∕2$ and $L=\ensuremath{\lambda}$, the most contrasted ones with respect to the length dependence of the coherent Dicke narrowing. For $L=\ensuremath{\lambda}∕2$, the Dicke-narrowed absorption profile simply broadens and saturates in amplitude when increasing the light intensity, while for $L=\ensuremath{\lambda}$, sub-Doppler dips of reduced absorption at the line-center appear on the broad absorption profile. For a fluorescence detection at $L=\ensuremath{\lambda}$, saturation induces narrow dips, but only for hyperfine components undergoing a population loss through optical pumping. These experimental results are interpreted with the help of the various existing models and are compared with numerical calculations based upon a two-level modeling that considers both a closed and an open system.

arXiv:0706.0837•Physical Review A•Jul 31, 2007•64 citations

A frequency reference based in VCSEL-driven dark line resonances in Cs vapor

John E. Kitching, N. Vukičević, Weidermann +5 more

Summary form only given. We report on recent experiments to use dark line coherent population trapping (CPT) resonances in cesium vapor as the basis for a compact frequency reference. The resonance is excited by directly modulating the injection current of a VCSEL at one-half the ground state hyperfine transition of Cs (4.6 GHz) to produce RF sidebands on the optical carrier. The laser output is then passed through a room-temperature cell containing Cs at its vapor pressure together with 8.7 kPa of Neon buffer gas and the transmitted optical power is detected in a photodiode. When the laser carrier is tuned half way between the two hyperfine components of the D/sub 2/ line at 852 nm, and the RF modulation frequency is adjusted to be equal to one-half the hyperfine splitting, the absorption of the sidebands through the cell is slightly reduced due to the CPT effect. As the RF frequency is scanned over the resonance, lock-in detection is used to produce a /spl sim/1 kHz wide dispersive error signal which is in turn used to stabilize the modulation frequency. The narrow signal is the result of the buffer gas, which reduces the time-of-flight broadening of the transition.

Quantum Electronics and Laser Science Conference•Jan 1, 2000•1 citation
Improvements in spectral resolution and sensitivity of a cesium based resonance fluorescence imaging monochromator (RFIM) are described. Alignment of the two lasers used in the excitation scheme in a co-propagating geometry have resulted in a detector spectral bandpass (270 MHz) that is narrower than the Doppler broadened profile (380 MHz) of cesium vapor at room temperature. Improvements in the experimental design, namely the addition of an image intensifier and cooled charge-coupled device (CCD) camera, have resulted in increased sensitivity; we report a limit of detection of 10 8 photons per pixel limited by image intensifier noise. Images of the cesium D 2 line emission (852.12 nm) from a cesium hollow cathode lamp were compared to an argon emission line (4Sº 1/2 → 4P 3/2 ) at 852.14 nm from a silver/argon hollow cathode lamp as a demonstration of the spectral resolution. The ability of the RFIM to discriminate between photons exciting the F = 4 vs. F = 3 ground state hyperfine level (a frequency difference of 9.2 GHz) of the cesium 6 2 S 1/2 state was also investigated to further demonstrate the spectral selectivity. The potential use of the described RFIM for chemical imaging applications is discussed.
A cesium-based resonance fluorescence monochromator with a spectral resolution of 200 MHz and a tunable response over the D(2) absorption line of cesium (380 MHz) is described. The narrow spectral response is achieved through excitation of a monokinetic population of the 6(2)P(3/2)( degrees ) state by arrangement of the excitation lasers in either a copropagating or a counterpropagating orientation. The narrow spectral response of the detector allows for excitation of specific hyperfine components involved in the 6(2)P(3/2)( degrees ) (F=3-5) to 6(2)D(5/2) (F=2-6) transition (917.23 nm). The selectivity gained through resolving specific hyperfine transitions allows for a photon detector that is both spectrally tunable and narrow. We report the sub-Doppler linewidths achieved through various laser beam orientations. We also describe how these beam geometries can be applied to spectrally narrow and tunable image detection.
The D1 line spectrally selective pumping process in Doppler-broadened cesium is analyzed by solving the optical Bloch equations. The process, described by a three-level model with the Λ scheme, shows that the saturation intensity of broadened atoms is three orders of magnitude larger than that of resting atoms. The |Fg = 3〉 → |Fe = 4〉 resonance pumping can result in the ground state |Fg = 4, mF = 4〉 sublevel having a maximum population of 0.157 and the population difference would be about 0.01 in two adjacent magnetic sublevels of the hyperfine (HF) state Fg = 4. To enhance the anisotropy in the ground state, we suggest employing dichromatic optical HF pumping by adding a laser to excite D1 line |Fg = 4〉 → |Fe = 3〉 transition, in which the cesium magnetometer sensitivity increases by half a magnitude and is unaffected by the nonlinear Zeeman effect even in Earth's average magnetic field.
The spectra of Rydberg atoms are of great significance for studying the energy levels of Rydberg atoms and the interaction between neutral atoms, especially, the high-precision spectra of Rydberg atoms can be used to measure the energy level shifts of Rydberg atoms resulting from the dipole-dipole interactions in room-temperature vapor cells. In this paper we report the preparation of cesium Rydberg states based on the cascaded two-photon excitation of 509 nm laser and 852 nm laser in opposite, and the measurements of the fine structure of cesium Rydberg states. In this experiment, the 509 nm laser is generated by the cavity-enhanced second-harmonic generation from 1018 nm laser with a periodically-poled KTP crystal and has a maximum power of about 1 W, and the 852 nm probe laser is provided by an external-cavity diode laser with a maximum output power of 5 mW and a typical linewidth of 1 MHz. By scanning the frequency of 509 nm coupling laser, it is presented that the Doppler-free spectra based on electromagnetically-induced transparency (EIT) of 509 nm coupling laser and 852 nm probe laser. The velocity-selective EIT spectra are used to study the spectral splitting of 6S1/26P3/257S(D) ladder-type system of cesium Rydberg atoms in a room-temperature vapor cell. The powers of 852 nm probe laser and 509 nm coupling laser are 0.3 upW and 200 mW, respectively. Their waist radii are both approximately 50 m. The intervals of hyperfine splitting of the intermediate state 6P3/2(F'=3, 4, 5) and fine splitting of 57D3/2 and 57D5/2 Rydberg states are measured by a frequency calibrating. Concretely, the velocity-selective spectrum with a radio frequency (RF) modulation of 30 MHz is used as a reference to calibrate the Rydberg fine-structure states in the hot vapor cell, where the RF frequency precision is smaller than a hertz on long time scales and the EIT linewidth is smaller than 13 MHz. The experimental value of the fine structure splitting of 57D3/2 and 57D5/2 Rydberg states is (354.72.5) MHz, that is in consistence with the value of 346.8 MHz calculated by Rydberg-Ritz equation and quantum defects of 57D3/2 and 57D5/2 Rydberg states. The experimental values of hyperfine splitting of intermediate state 6P3/2(F'=3, 4, 5) are also coincident with the theoretical calculated values. The dominant discrepancy existing between the experimental and calculated results may arise from the nonlinear correspondence of the PZT while the 509 nm wavelength cavity is scanned, and the measurement accuracy influenced by the spectral linewidth. The velocity-selective spectroscopy technique can also be used to measure the energy level shifts caused by the interactions of Rydberg atoms.
Abstract A novel technique to visualize RF waves in the gigahertz frequency range based on the double resonance spectroscopy of cesium-133 atoms is developed. This technique allows one to obtain fluorescence at a near-infrared wavelength of 852 nm, which can be detected by a charge-coupled device camera. The fluorescence depends on the strength distribution of 9.2 GHz RF waves. This method realizes real-time, high-resolution imaging using RF waves. In this study, the visualization of RF waves on a microstrip line is demonstrated and RF standing waves are clearly observed. The sensitivity of the visualization to the input power and phase shift of the RF standing waves arising from a particular condition of the reflection waves are investigated.
Saturation effects affecting absorption and fluorescence spectra of an atomic vapor confined in an extremely thin cell (cell thickness $L<1\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{m}$) are investigated experimentally and theoretically. The study is performed on the D2{D}_{2}D2​ line $(\ensuremath{\lambda}=852\phantom{\rule{0.3em}{0ex}}\mathrm{nm})$ of Cs and concentrates on the two situations $L=\ensuremath{\lambda}∕2$ and $L=\ensuremath{\lambda}$, the most contrasted ones with respect to the length dependence of the coherent Dicke narrowing. For $L=\ensuremath{\lambda}∕2$, the Dicke-narrowed absorption profile simply broadens and saturates in amplitude when increasing the light intensity, while for $L=\ensuremath{\lambda}$, sub-Doppler dips of reduced absorption at the line-center appear on the broad absorption profile. For a fluorescence detection at $L=\ensuremath{\lambda}$, saturation induces narrow dips, but only for hyperfine components undergoing a population loss through optical pumping. These experimental results are interpreted with the help of the various existing models and are compared with numerical calculations based upon a two-level modeling that considers both a closed and an open system.
Summary form only given. We report on recent experiments to use dark line coherent population trapping (CPT) resonances in cesium vapor as the basis for a compact frequency reference. The resonance is excited by directly modulating the injection current of a VCSEL at one-half the ground state hyperfine transition of Cs (4.6 GHz) to produce RF sidebands on the optical carrier. The laser output is then passed through a room-temperature cell containing Cs at its vapor pressure together with 8.7 kPa of Neon buffer gas and the transmitted optical power is detected in a photodiode. When the laser carrier is tuned half way between the two hyperfine components of the D/sub 2/ line at 852 nm, and the RF modulation frequency is adjusted to be equal to one-half the hyperfine splitting, the absorption of the sidebands through the cell is slightly reduced due to the CPT effect. As the RF frequency is scanned over the resonance, lock-in detection is used to produce a /spl sim/1 kHz wide dispersive error signal which is in turn used to stabilize the modulation frequency. The narrow signal is the result of the buffer gas, which reduces the time-of-flight broadening of the transition.