Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Soviet Journal of Quantum Electronics

Compact neodymium-glass amplifier for amplification of weak coherent radiation signals

E G Bordachev, V. I. Korolev, Victor A. Serebryakov, Anatoly D. Starikov

Published Dec 31, 1989• 5 citations
Publisher

Abstract

An investigation was made of the feasibility of using cavity flashlamps to develop neodymium glass amplifiers with a high gain M per pass for amplification of weak signals. Active elements made of GLS22P glass of varying diameter were inserted alternately in the internal cavity of INK-22 and INK-12 flashlamps. It was found that an increase in the density of packing the optical pumping system with the cavity flashlamps (an increase in the ratio of the radii of the active elements to the radius or the reflector) did not increase the pumping efficiency. Monitoring the effective lifetime of the excited particles established that the main reason for the fall in the amplifier efficiency with increasing pump energy (the greater the active element diameter, the steeper the fall) was the influence of superradiance processes. A gain M = 10 3 was achieved in an amplifier excited by an INK-22 cavity flashlamp with an active element 6 mm in diameter and 300 mm long (the excited part was 200 mm long) when the ratio of the stored excitation energy to the pump energy was ~ 0.015.

DOI
10.1070/qe1989v019n12abeh009814

Related papers

Regenerative glass-fiber neodymium quantum amplifier

M. I. Dzhibladze, E. Sh. Teplitskii, R. R. Erikashvili

Experimental and theoretical investigations were made of amplifying properties of an active neodymium glass fiber and a regenerative amplification regime was observed. It was found that the intensity gain of such a glass-fiber optical quantum amplifier increased exponentially on increase in the pump energy and corresponded to a regenerative regime. It was found that such a regenerative amplifier could operate on pulses above a certain minimum power. The experimental value of this minimum power was 10 mW. The maximum gain achieved in these experiments was 105 when the active length of the fiber was 40 cm.

Soviet Journal of Quantum Electronics•Jan 31, 1984•2 citations

Investigation of the parameters of a fiber optical quantum image amplifier

V L Koval'chuk, V P Konarev, V N Lomakin +1 more

An experimental investigation was made of the resolution of a neodymium-activated glass fiber laser image amplifier and of the dependence of the signal/noise ratio at the amplifier output on the signal power at the input. The resolution in the active regime (in the presence of pumping) was not inferior to that in the passive regime (without pumping) and the signal/noise ratio (and, consequently, the contrast of the amplified image) improved, compared with the passive regime.

Soviet Journal of Quantum Electronics•Apr 30, 1977•1 citation

Maximum gain of a multistage laser amplifier

A. I. Makarov, A. K. Potemkin

An investigation was made of the energy, spectral, angular, and temporal characteristics of superradiance emitted by a multistage neodymium glass amplifier with a gain of ~107. Superradiance was found to affect significantly the operation of the amplifier only when the gain reached ~107– 108.

Soviet Journal of Quantum Electronics•May 31, 1985•1 citation

Flashlamp Pumped Dye Amplifiers

Thomas Efthimiopoulos

The major purpose of the work described in this thesis is the experimental and theoretical study of the amplification of the spontaneous emission in dye amplifiers. This work falls into three distinct sections: (a) the study of high-current short-pulse flashtubes operating in (or near) the ablation regime; (b) the study of the amplification process of the spontaneous emission in a homogeneously broadened medium, such as a dye material, in the thin cell case, where there is no variation of the pumping across the cell; and, (c) the study of the amplification of the spontaneous emission in the thick cell case, where gain and index of refraction inhomogeneities exist across the cell thickness. In each case, we have developed theoretical models and compared their predictions with the experimental results. In particular, for the ablation-type flashlamps, it is shown that their behaviour is well represented by an analysis in which the discharge plasma is supposed to radiate as a blackbody at the temperature of the plasma. This model accounts for the fact that the light output from a flashlamp saturates whereas the current does not, provides a more accurate value for the plasma resistivity as a function of temperatures and gives a useful design criterion for determining the physical dimensions of an ablation-type flashlamp. With respect to the amplification of the spontaneous emission in a thin cell, it is mainly shown that (i) the spontaneous emission propagating along the gain medium is subject to narrowing along with shifting of its peak wavelength; (ii) even at moderate pumping the population of the excited singlet state, which determines the gain of the system, is non-uniform along the cell; (iii) it is possible to calculate the unsaturated gain by calculating the intensity of a particular wave-length and its spectral narrowing both as a function of the exciation and compare them with the same quantities measured experimentally; (iv) it is also possible to develop a semianalytic system independent method to measure the gain approximately. The theory developed to account for the propagation of the amplified spontaneous emission (ASE) has been partly extended to cover the case of the propagation and spectral narrowing of the ASE in a thick cell, where non-uniformities of the index of refraction and the gain are important along with the diffraction losses. In this particular case, it is shown that a model, which assumes an index step variation across the cell, and solves the Maxwell's equation for the field propagation along the cell, can account for the spatial distribution of the field across the cell and its manifestation at the far field. Most of the predictions of the model are verified experimentally. In particular, it is shown that (i) in a thick cell, part of the ASE propagates outside the gain medium, because of the lensing effect caused by heating of the lasing material; (ii) the field across the cell can exhibit stable spatial modes, which can produce a far field far from the amplifying cell axis; (iii) it is possible to improve the spectral narrowing of the ASE since saturation can be delayed to higher pumping than before and most of the narrowing occurs below saturation of the gain; (iv) it is also possible to measure the temperature and the index of refraction change due to heating by measuring the far field angle, and estimate the diffraction losses involved in the propagation of the ASE in a thick cell. Finally, a number of suggestions on further research are proposed.

•Oct 1, 1978•0 citations

Asymmetry of the amplification of light in optically dense active media

S. G. Voloshenyuk, L. V. Vovk, E I Zabello +1 more

An asymmetry effect in the amplification and efficiency of an optically dense amplifier is predicted theoretically and confirmed experimentally for opposite and concurrent collinear signal and pump paths. The effect is due to a difference in the losses as a result of the two-stage absorption of pump radiation in a system of luminescing centers described by a model of three energy levels. Calculations are made of various characteristics of this type of amplifier using the quasisteady-state approximation.

Soviet Journal of Quantum Electronics•May 31, 1989•2 citations

Photonic Crystal Microcavity Amplifier

D. Biallo, Antonella D’Orazio, M. De Sario +3 more

Summary form only given: Amplification in rare-earth doped solid state planar optical structures has attracted a lot of interest in recent years due to the fact that the rare earth ions show sharp absorption and emission bands and relatively long luminescence lifetimes. In particular the erbium (Er) ion is very attractive because of its intra 4f-transition from the first excited state to the ground state around 1.53 mum (4I13/2-4I15/2). The main problem of the erbium doped waveguide amplifiers (EDWAs) is that high values of the Er3+concentration are required to reach high gain figures in a compact length, but in this way the concentration quenching effects become very considerable and detrimental to the optical gain, since they reduce the population in the first excited state. A good solution to overcome this dramatic drawback is to consider erbium doped photonic crystal amplifier (EDPCA). In fact the small group velocity of electromagnetic eigenmodes brings about the enhancement of stimulated emission if the photonic crystals are doped by active media as the rare earth ions E3+r or Yt3+. This phenomenon originates from the long interaction time between radiation field and the matter caused by the small group velocity near the edge of the photonic band gap. The efficient confinement of light is achievable not only by tuning the input signal at the band edge of the gap of the photonic crystal but it is also obtainable by introducing local defects inside photonic crystals. The density of electromagnetic states inside a cavity is significantly modified and the spontaneous emission of atoms in a cavity can be either enhanced or inhibited. Erbium doped silica-titania one-dimensional photonic crystal microcavities have been analyzed by solving the erbium rate equations and the Maxwell equations by means of an auxiliary differential equation finite difference time domain technique. Since the performance of optical amplifiers depends on the populations of the energy levels participating in radiative transitions, determined principally by the distribution and concentration of the rare-earth ions and by the pumping conditions, the relations between these parameters and the transmittance of the EDPCMA have been studied

International Conference on Transparent Optical Networks•Jun 1, 2006•0 citations
An investigation was made of the feasibility of using cavity flashlamps to develop neodymium glass amplifiers with a high gain M per pass for amplification of weak signals. Active elements made of GLS22P glass of varying diameter were inserted alternately in the internal cavity of INK-22 and INK-12 flashlamps. It was found that an increase in the density of packing the optical pumping system with the cavity flashlamps (an increase in the ratio of the radii of the active elements to the radius or the reflector) did not increase the pumping efficiency. Monitoring the effective lifetime of the excited particles established that the main reason for the fall in the amplifier efficiency with increasing pump energy (the greater the active element diameter, the steeper the fall) was the influence of superradiance processes. A gain M = 10 3 was achieved in an amplifier excited by an INK-22 cavity flashlamp with an active element 6 mm in diameter and 300 mm long (the excited part was 200 mm long) when the ratio of the stored excitation energy to the pump energy was ~ 0.015.
Experimental and theoretical investigations were made of amplifying properties of an active neodymium glass fiber and a regenerative amplification regime was observed. It was found that the intensity gain of such a glass-fiber optical quantum amplifier increased exponentially on increase in the pump energy and corresponded to a regenerative regime. It was found that such a regenerative amplifier could operate on pulses above a certain minimum power. The experimental value of this minimum power was 10 mW. The maximum gain achieved in these experiments was 105 when the active length of the fiber was 40 cm.
The major purpose of the work described in this thesis is the experimental and theoretical study of the amplification of the spontaneous emission in dye amplifiers. This work falls into three distinct sections: (a) the study of high-current short-pulse flashtubes operating in (or near) the ablation regime; (b) the study of the amplification process of the spontaneous emission in a homogeneously broadened medium, such as a dye material, in the thin cell case, where there is no variation of the pumping across the cell; and, (c) the study of the amplification of the spontaneous emission in the thick cell case, where gain and index of refraction inhomogeneities exist across the cell thickness. In each case, we have developed theoretical models and compared their predictions with the experimental results. In particular, for the ablation-type flashlamps, it is shown that their behaviour is well represented by an analysis in which the discharge plasma is supposed to radiate as a blackbody at the temperature of the plasma. This model accounts for the fact that the light output from a flashlamp saturates whereas the current does not, provides a more accurate value for the plasma resistivity as a function of temperatures and gives a useful design criterion for determining the physical dimensions of an ablation-type flashlamp. With respect to the amplification of the spontaneous emission in a thin cell, it is mainly shown that (i) the spontaneous emission propagating along the gain medium is subject to narrowing along with shifting of its peak wavelength; (ii) even at moderate pumping the population of the excited singlet state, which determines the gain of the system, is non-uniform along the cell; (iii) it is possible to calculate the unsaturated gain by calculating the intensity of a particular wave-length and its spectral narrowing both as a function of the exciation and compare them with the same quantities measured experimentally; (iv) it is also possible to develop a semianalytic system independent method to measure the gain approximately. The theory developed to account for the propagation of the amplified spontaneous emission (ASE) has been partly extended to cover the case of the propagation and spectral narrowing of the ASE in a thick cell, where non-uniformities of the index of refraction and the gain are important along with the diffraction losses. In this particular case, it is shown that a model, which assumes an index step variation across the cell, and solves the Maxwell's equation for the field propagation along the cell, can account for the spatial distribution of the field across the cell and its manifestation at the far field. Most of the predictions of the model are verified experimentally. In particular, it is shown that (i) in a thick cell, part of the ASE propagates outside the gain medium, because of the lensing effect caused by heating of the lasing material; (ii) the field across the cell can exhibit stable spatial modes, which can produce a far field far from the amplifying cell axis; (iii) it is possible to improve the spectral narrowing of the ASE since saturation can be delayed to higher pumping than before and most of the narrowing occurs below saturation of the gain; (iv) it is also possible to measure the temperature and the index of refraction change due to heating by measuring the far field angle, and estimate the diffraction losses involved in the propagation of the ASE in a thick cell. Finally, a number of suggestions on further research are proposed.
An asymmetry effect in the amplification and efficiency of an optically dense amplifier is predicted theoretically and confirmed experimentally for opposite and concurrent collinear signal and pump paths. The effect is due to a difference in the losses as a result of the two-stage absorption of pump radiation in a system of luminescing centers described by a model of three energy levels. Calculations are made of various characteristics of this type of amplifier using the quasisteady-state approximation.
Summary form only given: Amplification in rare-earth doped solid state planar optical structures has attracted a lot of interest in recent years due to the fact that the rare earth ions show sharp absorption and emission bands and relatively long luminescence lifetimes. In particular the erbium (Er) ion is very attractive because of its intra 4f-transition from the first excited state to the ground state around 1.53 mum (4I13/2-4I15/2). The main problem of the erbium doped waveguide amplifiers (EDWAs) is that high values of the Er3+concentration are required to reach high gain figures in a compact length, but in this way the concentration quenching effects become very considerable and detrimental to the optical gain, since they reduce the population in the first excited state. A good solution to overcome this dramatic drawback is to consider erbium doped photonic crystal amplifier (EDPCA). In fact the small group velocity of electromagnetic eigenmodes brings about the enhancement of stimulated emission if the photonic crystals are doped by active media as the rare earth ions E3+r or Yt3+. This phenomenon originates from the long interaction time between radiation field and the matter caused by the small group velocity near the edge of the photonic band gap. The efficient confinement of light is achievable not only by tuning the input signal at the band edge of the gap of the photonic crystal but it is also obtainable by introducing local defects inside photonic crystals. The density of electromagnetic states inside a cavity is significantly modified and the spontaneous emission of atoms in a cavity can be either enhanced or inhibited. Erbium doped silica-titania one-dimensional photonic crystal microcavities have been analyzed by solving the erbium rate equations and the Maxwell equations by means of an auxiliary differential equation finite difference time domain technique. Since the performance of optical amplifiers depends on the populations of the energy levels participating in radiative transitions, determined principally by the distribution and concentration of the rare-earth ions and by the pumping conditions, the relations between these parameters and the transmittance of the EDPCMA have been studied