Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Performance of high-Tc superconducting quantum interference devices with resistively shunted inductances

Dae Joon Kang, W.E. Booij, Mark G. Blamire, Edward J. Tarte

Published Dec 28, 1998• 5 citations
Publisher

Abstract

The voltage modulation depths, ΔV of high-Tc direct current superconducting quantum interference devices (SQUIDs) with resistors connected in parallel with their inductances were investigated. Both the junctions and resistors in the SQUIDs were fabricated using focused electron-beam irradiation. The effect of varying the resistor value (using focused ion-beam trimming) and the screening parameter βL (by varying the temperature and hence the junction critical current) were studied. Significant enhancement of ΔV relative to an equivalent unshunted SQUID for βL values up to 50 was observed, and the most effective shunt resistor value was found to be approximately equal to the junction resistance.

DOI
10.1063/1.122939

Related papers

Performance of dc SQUIDs with resistively shunted inductance

Vittorio Foglietti, W. J. Gallagher, M. B. Ketchen +3 more

We have fabricated and characterized the noise performance of well-coupled Nb-Pb alloy edge junction dc superconducting quantum interference devices (SQUIDs) with a resistively shunted inductance. The extra damping resistor removes the resonances in the current-voltage characteristics resulting in a very low value of the extrinsic energy sensitivity in flux-locked-loop operation. Numerical simulations, with the junction capacitance included, indicate that the damping resistance does not degrade noise performance until it is significantly less than the junction-shunting resistance. We also tested different SQUID designs and demonstrated that a large SQUID inductance, proposed earlier to be desirable when resistively shunted, can seriously affect the low-frequency flux noise.

Applied Physics Letters•Oct 2, 1989•45 citations

Store–restore operation of flux quanta in coplanar type high Tc superconductive quantum interference devices

Hiroyuki Fuke, Kazuo Saitoh, Tadashi Utagawa +1 more

For a superconductive quantum interference device (SQUID) with rather large loop inductance for a single flux quantum, store–restore operation of flux quanta has been examined by external current pulses. To sense the stored flux quanta, the device includes another directly coupled SQUID as a magnetometer. Both of the coplanar type dc SQUIDs have been composed of Josephson junctions made by the narrow-focused ion beam irradiation technique in single-layer NdBa2Cu3O7−δ superconducting films. The SQUID has a critical current of 375 μA and an inductive parameter (βL) of 32. The number of stored flux quanta is controlled by the pulse signal height and the input terminal, but not by the number of pulses.

Journal of Applied Physics•Sep 1, 1998•1 citation

An insight into voltage-biased superconducting quantum interference devices

Chao Liu, Yi Zhang, Michael Mück +5 more

We experimentally studied two important parameters of helium-cooled superconducting quantum interference devices (SQUIDs) in the voltage bias mode: the dynamic resistance Rd and the flux-to-current transfer coefficient ∂i/∂Φ, with different junction shunt resistors RJ. We investigated a voltage-biased SQUID using the direct readout current-to-voltage converter scheme involving an operational amplifier. At higher RJ, the flux-to-voltage conversion coefficient ∂V/∂Φ becomes sufficiently large to effectively suppress the room-temperature amplifier's noise without any need for additional feedback circuits. The McCumber parameter limits the rise of ∂V/∂Φ. We discuss the performance of voltage-biased SQUIDs at different effective McCumber parameters.

Applied Physics Letters•Nov 26, 2012•20 citations

High Performance DC Superconducting Quantum Interference Device Utilizing a Bicrystal Junction with a 30° Misorientation Angle

Tadashi Minotani, Satoru Kawakami, Takanobu KISS +2 more

A high T c dc superconducting quantum interference device (SQUID) was fabricated using a bicrystal junction with a misorientation angle of θ=30°. The junction with a width of 2 µ m exhibited high resistance R s=10 Ω and critical current I 0=25 µ A at T=77 K. This gives a I 0 R s as high as 250 µ V. These values indicate that the bicrystal junction has great potential for the development of high performance SQUIDs. The SQUID fabricated with a 30° junction exhibited voltage modulation depths as high as ΔV=85 µ V, 40 µ V and 20 µ V at T=77 K for the inductance values of L s=60 pH, 100 pH and 160 pH, respectively. These are the highest values reported so far. Preliminary noise measurement showed that the flux noise of the SQUID is less than 8 µΦ0/ Hz1/2 for the white noise region, and less than 70 µΦ0/ Hz1/2 at f=1 Hz when the 60 pH-SQUID is dc biased and operated with a conventional Flux Locked Loop (FLL) circuit.

Japanese Journal of Applied Physics•Aug 1, 1997•30 citations

Direct current superconducting quantum interferometers with asymmetric shunt resistors

M. Rudolph, J. Nagel, J. M. Meckbach +5 more

We have investigated asymmetrically shunted Nb/Al-AlO$_x$/Nb direct current (dc) superconducting quantum interference devices (SQUIDs). While keeping the total resistance $R$ identical to a comparable symmetric SQUID with $R^{-1} = R_1^{-1} + R_2^{-1}$, we shunted only one of the two Josephson junctions with $R = R_{1,2}/2$. Simulations predict that the optimum energy resolution $ε$ and thus also the noise performance of such an asymmetric SQUID can be 3--4 times better than that of its symmetric counterpart. Experiments at a temperature of 4.2\,K yielded $ε\approx 32\,\hbar$ for an asymmetric SQUID with an inductance of $22\,\rm{pH}$. For a comparable symmetric device $ε= 110\,\hbar$ was achieved, confirming our simulation results.

arXiv:1207.0082•Applied Physics Letters•Jul 30, 2012•10 citations

Inductance analysis of superconducting quantum interference devices with 3D nano-bridge junctions

Hao Wang, Ruoting Yang, Guanqun Li +5 more

Abstract Superconducting quantum interference devices (SQUIDs) with 3D nano-bridge junctions can be miniaturized into nano-SQUIDs that are able to sense a few spins in a large magnetic field. Among all device parameters, the inductance is key to the performance of SQUIDs with 3D nano-bridge junctions. Here, we measured the critical-current magnetic flux modulation curves of 12 devices with three design types using a current strip-line directly coupled to the SQUID loop. A best flux modulation depth of 71% was achieved for our 3D Nb SQUID. From the modulation curves, we extracted the inductance values of the current stripe-line in each design and compared them with the corresponding simulation results of InductEX. In this way, London penetration depths of 110 and 420 nm were determined for our Nb (niobium) and NbN (niobium nitride) films, respectively. Furthermore, we showed that inductances of 11 and 119 pH for Nb and NbN 3D nano-bridge junctions, respectively, dominated the total inductance of our SQUID loops which are 23 pH for Nb and 255 pH for NbN. A screening parameter being equal to one suggests optimal critical currents of 89.6 and 8.1 μ A for Nb and NbN SQUIDs, respectively. Additionally, intrinsic flux noise of 110 ± 40 n Φ 0 /(Hz) 1/2 is calculated for the Nb SQUIDs with 3D nano-bridge junctions by Langevin simulation.

Superconductor Science and Technology•Mar 28, 2018•9 citations
The voltage modulation depths, ΔV of high-Tc direct current superconducting quantum interference devices (SQUIDs) with resistors connected in parallel with their inductances were investigated. Both the junctions and resistors in the SQUIDs were fabricated using focused electron-beam irradiation. The effect of varying the resistor value (using focused ion-beam trimming) and the screening parameter βL (by varying the temperature and hence the junction critical current) were studied. Significant enhancement of ΔV relative to an equivalent unshunted SQUID for βL values up to 50 was observed, and the most effective shunt resistor value was found to be approximately equal to the junction resistance.
We have fabricated and characterized the noise performance of well-coupled Nb-Pb alloy edge junction dc superconducting quantum interference devices (SQUIDs) with a resistively shunted inductance. The extra damping resistor removes the resonances in the current-voltage characteristics resulting in a very low value of the extrinsic energy sensitivity in flux-locked-loop operation. Numerical simulations, with the junction capacitance included, indicate that the damping resistance does not degrade noise performance until it is significantly less than the junction-shunting resistance. We also tested different SQUID designs and demonstrated that a large SQUID inductance, proposed earlier to be desirable when resistively shunted, can seriously affect the low-frequency flux noise.
For a superconductive quantum interference device (SQUID) with rather large loop inductance for a single flux quantum, store–restore operation of flux quanta has been examined by external current pulses. To sense the stored flux quanta, the device includes another directly coupled SQUID as a magnetometer. Both of the coplanar type dc SQUIDs have been composed of Josephson junctions made by the narrow-focused ion beam irradiation technique in single-layer NdBa2Cu3O7−δ superconducting films. The SQUID has a critical current of 375 μA and an inductive parameter (βL) of 32. The number of stored flux quanta is controlled by the pulse signal height and the input terminal, but not by the number of pulses.
We experimentally studied two important parameters of helium-cooled superconducting quantum interference devices (SQUIDs) in the voltage bias mode: the dynamic resistance Rd and the flux-to-current transfer coefficient ∂i/∂Φ, with different junction shunt resistors RJ. We investigated a voltage-biased SQUID using the direct readout current-to-voltage converter scheme involving an operational amplifier. At higher RJ, the flux-to-voltage conversion coefficient ∂V/∂Φ becomes sufficiently large to effectively suppress the room-temperature amplifier's noise without any need for additional feedback circuits. The McCumber parameter limits the rise of ∂V/∂Φ. We discuss the performance of voltage-biased SQUIDs at different effective McCumber parameters.
A high T c dc superconducting quantum interference device (SQUID) was fabricated using a bicrystal junction with a misorientation angle of θ=30°. The junction with a width of 2 µ m exhibited high resistance R s=10 Ω and critical current I 0=25 µ A at T=77 K. This gives a I 0 R s as high as 250 µ V. These values indicate that the bicrystal junction has great potential for the development of high performance SQUIDs. The SQUID fabricated with a 30° junction exhibited voltage modulation depths as high as ΔV=85 µ V, 40 µ V and 20 µ V at T=77 K for the inductance values of L s=60 pH, 100 pH and 160 pH, respectively. These are the highest values reported so far. Preliminary noise measurement showed that the flux noise of the SQUID is less than 8 µΦ0/ Hz1/2 for the white noise region, and less than 70 µΦ0/ Hz1/2 at f=1 Hz when the 60 pH-SQUID is dc biased and operated with a conventional Flux Locked Loop (FLL) circuit.
We have investigated asymmetrically shunted Nb/Al-AlOx_xx​/Nb direct current (dc) superconducting quantum interference devices (SQUIDs). While keeping the total resistance RRR identical to a comparable symmetric SQUID with R−1=R1−1+R2−1R^{-1} = R_1^{-1} + R_2^{-1}R−1=R1−1​+R2−1​, we shunted only one of the two Josephson junctions with R=R1,2/2R = R_{1,2}/2R=R1,2​/2. Simulations predict that the optimum energy resolution εεε and thus also the noise performance of such an asymmetric SQUID can be 3--4 times better than that of its symmetric counterpart. Experiments at a temperature of 4.2\,K yielded ε≈32 ℏε\approx 32\,\hbarε≈32ℏ for an asymmetric SQUID with an inductance of 22 pH22\,\rm{pH}22pH. For a comparable symmetric device ε=110 ℏε= 110\,\hbarε=110ℏ was achieved, confirming our simulation results.
Abstract Superconducting quantum interference devices (SQUIDs) with 3D nano-bridge junctions can be miniaturized into nano-SQUIDs that are able to sense a few spins in a large magnetic field. Among all device parameters, the inductance is key to the performance of SQUIDs with 3D nano-bridge junctions. Here, we measured the critical-current magnetic flux modulation curves of 12 devices with three design types using a current strip-line directly coupled to the SQUID loop. A best flux modulation depth of 71% was achieved for our 3D Nb SQUID. From the modulation curves, we extracted the inductance values of the current stripe-line in each design and compared them with the corresponding simulation results of InductEX. In this way, London penetration depths of 110 and 420 nm were determined for our Nb (niobium) and NbN (niobium nitride) films, respectively. Furthermore, we showed that inductances of 11 and 119 pH for Nb and NbN 3D nano-bridge junctions, respectively, dominated the total inductance of our SQUID loops which are 23 pH for Nb and 255 pH for NbN. A screening parameter being equal to one suggests optimal critical currents of 89.6 and 8.1 μ A for Nb and NbN SQUIDs, respectively. Additionally, intrinsic flux noise of 110 ± 40 n Φ 0 /(Hz) 1/2 is calculated for the Nb SQUIDs with 3D nano-bridge junctions by Langevin simulation.