Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Review of Scientific Instruments

Sensitivity enhancement of Quantum Design dc superconducting quantum interference devices in two-stage configuration

R. Mezzena, Andrea Vinante, P. Falferi, Stefano Vitale, M. Bonaldi, Giovanni Andrea Prodi, MASSIMO CERDONIO, M. B. Simmonds

Published Sep 1, 2001• 31 citations
Publisher

Abstract

The energy sensitivity of a direct current (dc) superconducting quantum interference device (SQUID) can be improved if it is operated in a two-stage configuration. Employing this technique, a commercial dc SQUID system was modified and made competitive with other sensors especially designed for very low noise applications. We report the noise measurements performed in the temperature range 4.2 K–25 mK. At 4.2 K, the coupled energy sensitivity obtained with the two-stage dc SQUID was approximately ten times better than with a conventional readout electronics. The noise energy decreases linearly until approximately 300 mK, in good agreement with theoretical previsions. At lower temperature the hot-electron effect produces a saturation and the best energy sensitivity measured with open input coil is 35 ℏ.

DOI
10.1063/1.1389496

Related papers

Development of low-noise two-stage dc-SQUID for TES detector readout

Nan Li, Mengjie Song, Sixiao Hu +9 more

Abstract Direct-current superconducting quantum interference devices (dc-SQUIDs) are one of the most sensitive magnetic detectors. These sensors are extensively used in the readout of superconducting transition edge sensors (TESs), which are used for the detection of weak signals. A cosmic microwave background (CMB) polarization telescope operating in 22–48 GHz is currently under developing. The TESs calorimeter of the telescope will be readout by a time-division multiplexer SQUID readout system. We develop a two-stage dc-SQUID amplifier circuit, comprising an input-stage SQUID with 4 SQUID cells and a series SQUID array with 100 SQUID cells. This configuration has been shown to achieve extremely high signal gain while effectively controlling system noise. We assess the system noise at 300 mK in an adiabatic demagnetization refrigerator. The measured magnetic flux noise of the two-stage SQUID circuit system is approximately 0.3 μ Φ 0 / Hz at 10 kHz. The current noise equivalent to the input coil of input SQUID is about 2.4 pA / Hz . This result meets the low-noise readout requirements of the CMB TES and other applications with TES detectors.

arXiv:2601.19565•Superconductor Science and Technology•Apr 1, 2026•0 citations

Optimization of a Low-Tc DC SQUID Amplifier With Tightly Coupled Input Coils

J. Pleikies, O. Usenko, G. Frossati +1 more

We optimized the design and operation of a low-Tc direct current superconducting quantum interference device (dc SQUID) with an integrated coupling coil of 1.5 muH inductance taking into account typical effects observed for similar devices. Numerical simulations were performed on a model including the capacitance of the Josephson junctions, thermal noise of the integrated shunt- and damping- resistors as well as a complex frequency dependent impedance of the SQUID loop originating from the integrated coils. The experimentally and numerically determined characteristics and sensitivity are in good agreement. A minimum additional coupled energy resolution of 700 (h/2p) and 250 (h/2p) was measured at a temperature of 4.2 K and 1.5 K, respectively.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•6 citations

Strongly coupled, low noise dc-SQUID amplifiers

J. Pleikies

The dc Superconducting Quantum Interference Device (dc-SQUID) is one of the most sensitive magnetic field sensors available. In this thesis we concentrate on its application as an amplifier. In this configuration, an input circuit of interest can be connected by means of a coupling coil. The intended application of our developed low-Tc SQUID amplifiers is the readout of the first spherical gravitational wave antenna MiniGRAIL. Using small-signal analysis as well as numerical simulations, we study the achievable signal-to-noise ratio of such sensors in practical measurements. Published theories and studies could be extended. Some interesting points treated are the influence of the often used negative feedback (flux-locked loop), an altered input impedance of the SQUID amplifier and the influence of back-action noise, which directly affects the object of interest. The altered operation of the SQUID due to the presence of the input circuit is studied in numerical experiments. Another important issue, the influence of integrated input coils on the dynamics of SQUIDs, is investigated theoretically and experimentally. The performance of our developed sensors is compared to numerical simulations on detailed models. The results give insights into the behavior, design and usage of dc-SQUIDs with integrated coils. For a SQUID with input inductances of 1.5 μH we reached a good coupled energy sensitivity of about 170 ¯h in a dilution refrigerator. Furthermore, we investigated the hot-electron effect. This effect typically limits the sensitivity of superconducting electronics at sub-Kelvin bath temperatures due to a weakened electron-phonon coupling. We performed heating experiments on thin-film resistors which are similar to the shunt resistors of the Josephson junctions used in our sensors. The suppression of the hot-electron effect via electronic thermal transport to attached cooling fins is investigated both experimentally, theoretically and numerically. The numerical technique turns out to be a useful tool for the thermal design of superconducting electronics.

•Apr 1, 2009•0 citations

Use of low-noise dc-SQUIDs in fundamental physics experiments

P. Carelli, Maria Gabriella Castellano, Roberto Leoni +1 more

The noise performance of dc-SQUIDs (Superconducting Quantum Interference Devices), which nowadays can reach values close to the quantum limit, makes them very attractive as amplifiers for experiments using low temperatures and demanding for extremely high sensitivity. After reviewing the working principle of the dc-SQUID, we describe a thin-film device with a new structure, which allowed us to reach an energy sensitivity of 5.5 h- at 0.9 K and a good coupling with a large input coil. At last we discuss some fundamental physics experiments which take advantage from the SQUID use.

Journal de Physique IV (Proceedings)•Jun 1, 1998•0 citations

A low-noise, two-stage DC SQUID amplifier with high bandwidth and dynamic range

R. Cantor, L. P. Lee, Andrei N. Matlashov +1 more

We describe a low-noise, two-stage dc Superconducting QUantum Interference Device (SQUID) amplifier that is designed for applications requiring high bandwidth and dynamic range. The output signal of a low-noise SQUID in the input stage coherently modulates a series array of identical SQUIDs in the output stage via a common modulation line. The input stage is designed so its output signal does not produce multiple modulation periods in the output stage. The output stage is designed to have sufficient gain so the output noise is dominated by the amplified noise of the input SQUID and exceeds the noise of a preamplifier in the room temperature readout electronics. The SQUID amplifier may therefore be operated without flux modulation or any impedance matching network, resulting in a large dynamic range and high bandwidth.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•11 citations

A dc SQUID for use below 1 K

Z. K. Geng, P. W. Adams, William O. Hamilton +2 more

For detection of weak signals, and for use on ultralow temperature experiments, it would be useful to have a robust superconducting quantum interference device (SQUID) amplifier that works below 1 K. We report on a test of a commercial SQUID amplifier that has lower noise than others we have tested, and works well while attached to a 50-mK chamber. The SQUID noise was improved only modestly when cooled from 4 K to 50 mK. The best energy resolution measured was 2200 ℏ.

Review of Scientific Instruments•May 1, 1993•10 citations
The energy sensitivity of a direct current (dc) superconducting quantum interference device (SQUID) can be improved if it is operated in a two-stage configuration. Employing this technique, a commercial dc SQUID system was modified and made competitive with other sensors especially designed for very low noise applications. We report the noise measurements performed in the temperature range 4.2 K–25 mK. At 4.2 K, the coupled energy sensitivity obtained with the two-stage dc SQUID was approximately ten times better than with a conventional readout electronics. The noise energy decreases linearly until approximately 300 mK, in good agreement with theoretical previsions. At lower temperature the hot-electron effect produces a saturation and the best energy sensitivity measured with open input coil is 35 ℏ.
Abstract Direct-current superconducting quantum interference devices (dc-SQUIDs) are one of the most sensitive magnetic detectors. These sensors are extensively used in the readout of superconducting transition edge sensors (TESs), which are used for the detection of weak signals. A cosmic microwave background (CMB) polarization telescope operating in 22–48 GHz is currently under developing. The TESs calorimeter of the telescope will be readout by a time-division multiplexer SQUID readout system. We develop a two-stage dc-SQUID amplifier circuit, comprising an input-stage SQUID with 4 SQUID cells and a series SQUID array with 100 SQUID cells. This configuration has been shown to achieve extremely high signal gain while effectively controlling system noise. We assess the system noise at 300 mK in an adiabatic demagnetization refrigerator. The measured magnetic flux noise of the two-stage SQUID circuit system is approximately 0.3 μ Φ 0 / Hz at 10 kHz. The current noise equivalent to the input coil of input SQUID is about 2.4 pA / Hz . This result meets the low-noise readout requirements of the CMB TES and other applications with TES detectors.
We optimized the design and operation of a low-Tc direct current superconducting quantum interference device (dc SQUID) with an integrated coupling coil of 1.5 muH inductance taking into account typical effects observed for similar devices. Numerical simulations were performed on a model including the capacitance of the Josephson junctions, thermal noise of the integrated shunt- and damping- resistors as well as a complex frequency dependent impedance of the SQUID loop originating from the integrated coils. The experimentally and numerically determined characteristics and sensitivity are in good agreement. A minimum additional coupled energy resolution of 700 (h/2p) and 250 (h/2p) was measured at a temperature of 4.2 K and 1.5 K, respectively.
The dc Superconducting Quantum Interference Device (dc-SQUID) is one of the most sensitive magnetic field sensors available. In this thesis we concentrate on its application as an amplifier. In this configuration, an input circuit of interest can be connected by means of a coupling coil. The intended application of our developed low-Tc SQUID amplifiers is the readout of the first spherical gravitational wave antenna MiniGRAIL. Using small-signal analysis as well as numerical simulations, we study the achievable signal-to-noise ratio of such sensors in practical measurements. Published theories and studies could be extended. Some interesting points treated are the influence of the often used negative feedback (flux-locked loop), an altered input impedance of the SQUID amplifier and the influence of back-action noise, which directly affects the object of interest. The altered operation of the SQUID due to the presence of the input circuit is studied in numerical experiments. Another important issue, the influence of integrated input coils on the dynamics of SQUIDs, is investigated theoretically and experimentally. The performance of our developed sensors is compared to numerical simulations on detailed models. The results give insights into the behavior, design and usage of dc-SQUIDs with integrated coils. For a SQUID with input inductances of 1.5 μH we reached a good coupled energy sensitivity of about 170 ¯h in a dilution refrigerator. Furthermore, we investigated the hot-electron effect. This effect typically limits the sensitivity of superconducting electronics at sub-Kelvin bath temperatures due to a weakened electron-phonon coupling. We performed heating experiments on thin-film resistors which are similar to the shunt resistors of the Josephson junctions used in our sensors. The suppression of the hot-electron effect via electronic thermal transport to attached cooling fins is investigated both experimentally, theoretically and numerically. The numerical technique turns out to be a useful tool for the thermal design of superconducting electronics.
The noise performance of dc-SQUIDs (Superconducting Quantum Interference Devices), which nowadays can reach values close to the quantum limit, makes them very attractive as amplifiers for experiments using low temperatures and demanding for extremely high sensitivity. After reviewing the working principle of the dc-SQUID, we describe a thin-film device with a new structure, which allowed us to reach an energy sensitivity of 5.5 h- at 0.9 K and a good coupling with a large input coil. At last we discuss some fundamental physics experiments which take advantage from the SQUID use.
We describe a low-noise, two-stage dc Superconducting QUantum Interference Device (SQUID) amplifier that is designed for applications requiring high bandwidth and dynamic range. The output signal of a low-noise SQUID in the input stage coherently modulates a series array of identical SQUIDs in the output stage via a common modulation line. The input stage is designed so its output signal does not produce multiple modulation periods in the output stage. The output stage is designed to have sufficient gain so the output noise is dominated by the amplified noise of the input SQUID and exceeds the noise of a preamplifier in the room temperature readout electronics. The SQUID amplifier may therefore be operated without flux modulation or any impedance matching network, resulting in a large dynamic range and high bandwidth.