Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Time-domain multiplexed SQUID readout of a bolometer camera for APEX

V. Zakosarenko, Marco Schulz, Alan B. Krueger, Erik Heinz, Solveig Anders, Katja Peiselt, T. May, E. Kreysa, G. Siringo, Walter Esch, M. Starkloff, H.‐G. Meyer

Published Dec 10, 2010• 20 citations
Publisher

Abstract

We describe the development and fabrication of the sub-millimeter APEX (Atacama pathfinder experiment) bolometer camera (SABOCA) and its installation at the APEX radio telescope in Chile. SABOCA has 37 bolometers for a wavelength of about 0.35 mm. The bolometers with superconducting transition-edge sensors are read out by superconducting quantum interference devices (SQUIDs). Time-domain multiplexing was used to compress 40 readout signals into four output channels, which are further amplified by superconducting quantum interference filters (SQIF). The multiplexer readout circuit is described in detail. One spare SQUID and two spare bolometers have been used as reference to evaluate contributions to the bolometer noise figure. SABOCA's electrical noise equivalent power is about 7 × 10 − 16 W Hz − 1/2 , whereas the optical noise equivalent flux density measured at APEX is better than 0.35 Jy Hz − 1/2 (1 Jy = 10 − 26 W m − 2 Hz − 1 ). The measured bolometer noise exceeds the theoretical estimation by factor of two, possibly caused by excess noise in the transition-edge sensor. Nevertheless the achieved instrumental sensitivity meets the specification given by the APEX board. SABOCA was commissioned as the facility instrument in the spring of 2009.

DOI
10.1088/0953-2048/24/1/015011

Related papers

Frequency multiplexed superconducting quantum interference device readout of large bolometer arrays for cosmic microwave background measurements

M. Dobbs, Martin Lueker, K. A. Aird +44 more

A technological milestone for experiments employing transition edge sensor bolometers operating at sub-Kelvin temperature is the deployment of detector arrays with 100s-1000s of bolometers. One key technology for such arrays is readout multiplexing: the ability to read out many sensors simultaneously on the same set of wires. This paper describes a frequency-domain multiplexed readout system which has been developed for and deployed on the APEX-SZ and South Pole Telescope millimeter wavelength receivers. In this system, the detector array is divided into modules of seven detectors, and each bolometer within the module is biased with a unique ∼MHz sinusoidal carrier such that the individual bolometer signals are well separated in frequency space. The currents from all bolometers in a module are summed together and pre-amplified with superconducting quantum interference devices operating at 4 K. Room temperature electronics demodulate the carriers to recover the bolometer signals, which are digitized separately and stored to disk. This readout system contributes little noise relative to the detectors themselves, is remarkably insensitive to unwanted microphonic excitations, and provides a technology pathway to multiplexing larger numbers of sensors.

arXiv:1112.4215•Review of Scientific Instruments•Jul 1, 2012•145 citations

A microwave SQUID multiplexer optimized for bolometric applications

B. Dober, Zeeshan Ahmed, K. Arnold +27 more

A microwave superconducting quantum interference device multiplexer has been optimized for reading out large arrays of superconducting transition-edge sensor (TES) bolometers. We present the scalable cryogenic multiplexer chip design that may be used to construct an 1820-channel multiplexer for the 4–8 GHz rf band. The key metrics of yield, sensitivity, and crosstalk are determined through measurements of 455 readout channels, which span 4–5 GHz. The median white-noise level is 45 pA/Hz, evaluated at 2 Hz, with a 1/f knee ≤ 20 mHz after common-mode subtraction. The white-noise level decreases the sensitivity of a TES bolometer optimized for detection of the cosmic microwave background at 150 GHz by only 3%. The measured crosstalk between any channel pair is ≤ 0.3%.

arXiv:2010.07998•Applied Physics Letters•Feb 8, 2021•63 citations

Development of a microwave SQUID multiplexer for superconducting transition-edge sensor bolometer arrays

Zhi-Fa Feng, Xian-Feng Zhou, M Y Li +10 more

Abstract A microwave SQUID multiplexer ( μ MUX) with a high multiplexing factor is a promising readout approach for large-scale superconducting transition-edge sensor (TES) bolometer arrays. This paper reports on the characteristics of 16-channel μ MUX prototype chips and a 60-channel readout module developed to read out TES bolometers for the Ali cosmic microwave background polarization telescope (AliCPT). We designed two different coupling structures between the resonator and the radio-frequency superconducting interference device: design A with a mutual inductance ( M T ) of 2.3 pH and design B with an M T of 6.5 pH. For design A, the mean resonator bandwidth ( Δ f BW ) and peak-to-peak frequency shift ( Δ f pp ) are approximately 610 kHz and 290 kHz, respectively. The measured mean open-loop current noise is less than 40 pA / Hz . Preliminary results indicate that crosstalk between adjacent channels is below 1% in our design A μ MUX chip. A measured channel with design B shows a Δ f BW of 586 kHz and a current noise of 33 pA / Hz , similar to the design A channels. In comparison, the Δ f pp of 803 kHz is much larger than the design A channels due to a larger M T . The readout module, consisting of two design A chips and two design B chips, shows 60 resonances, corresponding to a yield of 94%. In the future, we will place 32 design A channels within the same chip dimension to increase the channel density and build a larger readout module suitable for AliCPT TES arrays.

Superconductor Science and Technology•Sep 1, 2026•0 citations

Frequency-domain multiplexed readout of transition-edge sensor arrays with a superconducting quantum interference device

Trevor M. Lanting, Hsiao-Mei Cho, John L. Clarke +7 more

We demonstrate an eight-channel frequency-domain readout multiplexer for superconducting transition-edge sensors (TESs). Each sensor is biased with a sinusoidal voltage at a unique frequency. The sensor currents are summed and measured with a single superconducting quantum interference device (SQUID) array. The 100-element SQUID array is operated with shunt feedback electronics that have a slew rate of 1.2×107Φ0∕s at 1MHz. The multiplexer readout noise is 6.5pA∕Hz, which is well below the expected sensor noise of 15pA∕Hz. We measure an upper limit on adjacent channel crosstalk of 0.004, which meets our design requirements. The demodulated noise spectra of multiplexed TESs are white at frequencies down to 200mHz.

Applied Physics Letters•Mar 11, 2005•96 citations

The Microwave SQUID Multiplexer

J. A. B. Mates

This thesis describes a multiplexer of Superconducting Quantum Interference Devices (SQUIDs) with low-noise, ultra-low power dissipation, and great scalability. The multiplexer circuit measures the magnetic flux in a large number of unshunted rf SQUIDs by coupling each SQUID to a superconducting microwave resonator tuned to a unique resonance frequency and driving the resonators from a common feedline. A superposition of microwave tones measures each SQUID simultaneously using only two coaxial cables between the cryogenic device and room temperature. This multiplexer will enable the instrumentation of arrays with hundreds of thousands of low-temperature detectors for new applications in cosmology, materials analysis, and nuclear non-proliferation.\nThe driving application of the Microwave SQUID Multiplexer is the readout of large arrays of superconducting transition-edge sensors, by some figures of merit the most sensitive detectors of electromagnetic signals over a span of more than nine orders of magnitude in energy, from 40 GHz microwaves to 200 keV gamma rays. Modern transition-edge sensors have noise-equivalent power as low as 10-20 W / [square root] Hz and energy resolution as good as 2 eV at 6 keV. These per-pixel sensitivities approach theoretical limits set by the underlying signals, motivating a rapid increase in pixel count to access new science. Compelling applications, like the non-destructive assay of nuclear material for treaty verification or the search for primordial gravity waves from inflation use arrays of these detectors to increase collection area or tile a focal plane.\nWe developed three generations of SQUID multiplexers, optimizing the first for flux noise (0.17 mu Phi0 / [square root] Hz) the second for input current noise (19 pA / [square root] Hz) and the last for practical multiplexing of large arrays of cosmic microwave background polarimeters based on transition-edge sensors. Using the last design we demonstrated multiplexed readout of prototype polarimeters with the performance required for the future development of a large-scale astronomical instrument.

•Dec 1, 2011•43 citations

Frequency-Domain SQUID Multiplexing of Transition-Edge Sensors

Trevor M. Lanting, Hsiao-Mei Cho, John L. Clarke +7 more

We describe our frequency-domain readout multiplexer for transition-edge sensor (TES) bolometers and present measurements of an eight-channel multiplexer. Each sensor is biased with a sinusoidal bias at a distinct frequency. As the sensor absorbs power, it amplitude-modulates its sinusoidal bias. Sensor currents are summed and measured with a single superconducting quantum interference device (SQUID) array. The SQUID array consists of 100 dc-SQUID's in series and is operated with shunt feedback electronics which have a slew rate of 1.210/sup 7/ /spl Phi//sub 0//s. A tuned filter consisting of an inductor and capacitor are placed in series with each sensor to both limit the bandwidth of the Nyquist noise from each sensor and to allow us to bias all multiplexed sensors with a common wire. We place an upper limit on crosstalk between adjacent channels of 0.004, well below our design requirements. Demodulated noise spectra from multiplexed sensors show the expected white noise levels at frequencies above 200 mHz.

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•2 citations
We describe the development and fabrication of the sub-millimeter APEX (Atacama pathfinder experiment) bolometer camera (SABOCA) and its installation at the APEX radio telescope in Chile. SABOCA has 37 bolometers for a wavelength of about 0.35 mm. The bolometers with superconducting transition-edge sensors are read out by superconducting quantum interference devices (SQUIDs). Time-domain multiplexing was used to compress 40 readout signals into four output channels, which are further amplified by superconducting quantum interference filters (SQIF). The multiplexer readout circuit is described in detail. One spare SQUID and two spare bolometers have been used as reference to evaluate contributions to the bolometer noise figure. SABOCA's electrical noise equivalent power is about 7 × 10 − 16 W Hz − 1/2 , whereas the optical noise equivalent flux density measured at APEX is better than 0.35 Jy Hz − 1/2 (1 Jy = 10 − 26 W m − 2 Hz − 1 ). The measured bolometer noise exceeds the theoretical estimation by factor of two, possibly caused by excess noise in the transition-edge sensor. Nevertheless the achieved instrumental sensitivity meets the specification given by the APEX board. SABOCA was commissioned as the facility instrument in the spring of 2009.
A technological milestone for experiments employing transition edge sensor bolometers operating at sub-Kelvin temperature is the deployment of detector arrays with 100s-1000s of bolometers. One key technology for such arrays is readout multiplexing: the ability to read out many sensors simultaneously on the same set of wires. This paper describes a frequency-domain multiplexed readout system which has been developed for and deployed on the APEX-SZ and South Pole Telescope millimeter wavelength receivers. In this system, the detector array is divided into modules of seven detectors, and each bolometer within the module is biased with a unique ∼MHz sinusoidal carrier such that the individual bolometer signals are well separated in frequency space. The currents from all bolometers in a module are summed together and pre-amplified with superconducting quantum interference devices operating at 4 K. Room temperature electronics demodulate the carriers to recover the bolometer signals, which are digitized separately and stored to disk. This readout system contributes little noise relative to the detectors themselves, is remarkably insensitive to unwanted microphonic excitations, and provides a technology pathway to multiplexing larger numbers of sensors.
A microwave superconducting quantum interference device multiplexer has been optimized for reading out large arrays of superconducting transition-edge sensor (TES) bolometers. We present the scalable cryogenic multiplexer chip design that may be used to construct an 1820-channel multiplexer for the 4–8 GHz rf band. The key metrics of yield, sensitivity, and crosstalk are determined through measurements of 455 readout channels, which span 4–5 GHz. The median white-noise level is 45 pA/Hz, evaluated at 2 Hz, with a 1/f knee ≤ 20 mHz after common-mode subtraction. The white-noise level decreases the sensitivity of a TES bolometer optimized for detection of the cosmic microwave background at 150 GHz by only 3%. The measured crosstalk between any channel pair is ≤ 0.3%.
Abstract A microwave SQUID multiplexer ( μ MUX) with a high multiplexing factor is a promising readout approach for large-scale superconducting transition-edge sensor (TES) bolometer arrays. This paper reports on the characteristics of 16-channel μ MUX prototype chips and a 60-channel readout module developed to read out TES bolometers for the Ali cosmic microwave background polarization telescope (AliCPT). We designed two different coupling structures between the resonator and the radio-frequency superconducting interference device: design A with a mutual inductance ( M T ) of 2.3 pH and design B with an M T of 6.5 pH. For design A, the mean resonator bandwidth ( Δ f BW ) and peak-to-peak frequency shift ( Δ f pp ) are approximately 610 kHz and 290 kHz, respectively. The measured mean open-loop current noise is less than 40 pA / Hz . Preliminary results indicate that crosstalk between adjacent channels is below 1% in our design A μ MUX chip. A measured channel with design B shows a Δ f BW of 586 kHz and a current noise of 33 pA / Hz , similar to the design A channels. In comparison, the Δ f pp of 803 kHz is much larger than the design A channels due to a larger M T . The readout module, consisting of two design A chips and two design B chips, shows 60 resonances, corresponding to a yield of 94%. In the future, we will place 32 design A channels within the same chip dimension to increase the channel density and build a larger readout module suitable for AliCPT TES arrays.
We demonstrate an eight-channel frequency-domain readout multiplexer for superconducting transition-edge sensors (TESs). Each sensor is biased with a sinusoidal voltage at a unique frequency. The sensor currents are summed and measured with a single superconducting quantum interference device (SQUID) array. The 100-element SQUID array is operated with shunt feedback electronics that have a slew rate of 1.2×107Φ0∕s at 1MHz. The multiplexer readout noise is 6.5pA∕Hz, which is well below the expected sensor noise of 15pA∕Hz. We measure an upper limit on adjacent channel crosstalk of 0.004, which meets our design requirements. The demodulated noise spectra of multiplexed TESs are white at frequencies down to 200mHz.
This thesis describes a multiplexer of Superconducting Quantum Interference Devices (SQUIDs) with low-noise, ultra-low power dissipation, and great scalability. The multiplexer circuit measures the magnetic flux in a large number of unshunted rf SQUIDs by coupling each SQUID to a superconducting microwave resonator tuned to a unique resonance frequency and driving the resonators from a common feedline. A superposition of microwave tones measures each SQUID simultaneously using only two coaxial cables between the cryogenic device and room temperature. This multiplexer will enable the instrumentation of arrays with hundreds of thousands of low-temperature detectors for new applications in cosmology, materials analysis, and nuclear non-proliferation.\nThe driving application of the Microwave SQUID Multiplexer is the readout of large arrays of superconducting transition-edge sensors, by some figures of merit the most sensitive detectors of electromagnetic signals over a span of more than nine orders of magnitude in energy, from 40 GHz microwaves to 200 keV gamma rays. Modern transition-edge sensors have noise-equivalent power as low as 10-20 W / [square root] Hz and energy resolution as good as 2 eV at 6 keV. These per-pixel sensitivities approach theoretical limits set by the underlying signals, motivating a rapid increase in pixel count to access new science. Compelling applications, like the non-destructive assay of nuclear material for treaty verification or the search for primordial gravity waves from inflation use arrays of these detectors to increase collection area or tile a focal plane.\nWe developed three generations of SQUID multiplexers, optimizing the first for flux noise (0.17 mu Phi0 / [square root] Hz) the second for input current noise (19 pA / [square root] Hz) and the last for practical multiplexing of large arrays of cosmic microwave background polarimeters based on transition-edge sensors. Using the last design we demonstrated multiplexed readout of prototype polarimeters with the performance required for the future development of a large-scale astronomical instrument.
We describe our frequency-domain readout multiplexer for transition-edge sensor (TES) bolometers and present measurements of an eight-channel multiplexer. Each sensor is biased with a sinusoidal bias at a distinct frequency. As the sensor absorbs power, it amplitude-modulates its sinusoidal bias. Sensor currents are summed and measured with a single superconducting quantum interference device (SQUID) array. The SQUID array consists of 100 dc-SQUID's in series and is operated with shunt feedback electronics which have a slew rate of 1.210/sup 7/ /spl Phi//sub 0//s. A tuned filter consisting of an inductor and capacitor are placed in series with each sensor to both limit the bandwidth of the Nyquist noise from each sensor and to allow us to bias all multiplexed sensors with a common wire. We place an upper limit on crosstalk between adjacent channels of 0.004, well below our design requirements. Demodulated noise spectra from multiplexed sensors show the expected white noise levels at frequencies above 200 mHz.