Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

Laser diodes for optical readout of cryo-electronics

Lewis A. Bunz, Sergey V. Rylov, Elie K. Track

Published Jun 23, 1994• 4 citations
Publisher

Abstract

We report successful coupling of electrical signals from low temperature (4.2 K) superconducting circuitry to room temperature electronics using laser diodes coupled to optical fibers. The techniques used rely on laser diodes operating at low temperatures, and on high gain amplifiers placed outside the low temperature environment. A new superconducting driver circuit is used to step-up the low output of these circuits to a seven millivolt level, sufficient to modulate the laser diodes. By properly choosing the laser source, the power dissipated within the cryogenic environment can be maintained below 400 (mu) W, with further improvements easily reached.

DOI
10.1117/12.178492

Related papers

Fiber optic input and output for superconducting circuits

Lewis A. Bunz, Elie K. Track, Sergey V. Rylov +2 more

Superconducting devices operate at speeds where coaxial copper cables can be a limiting factor. Coaxial cables can limit frequency response and impose significant thermal loading on a cyrogenic system. The high bandwidth of optical fibers and their low thermal conductivity make them good candidates for providing data into and out of superconducting circuits. In this paper, we present the results of our experience in operating photodetectors and laser diodes together with superconducting circuits in the same low temperature (4.2 K) environment. Using these photodetectors, we demonstrate the input of optical signals to an analog superconducting circuit at 6 GHz. Output from a superconducting circuit operating at 500 MHz is fed into a laser diode, and optically coupled to room temperature electronics. By combining these two techniques, we demonstrate a fully operational superconducting shift register with both input and output signals supplied by optical fiber.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jul 2, 1994•16 citations

A cryogenic electro-optic interconnect for superconducting devices

Amir Youssefi, Itay Shomroni, Yash J. Joshi +5 more

A major challenge to the scalability of cryogenic computing platforms is the heat load associated with the growing number of electrical cable connections between the superconducting circuitry and the room-temperature environment. Compared with electrical cables, optical fibres have significantly lower thermal conductivity and are widely used in modern telecommunications. However, optical modulation at cryogenic temperatures remains relatively unexplored. Here we report the cryogenic electro-optical readout of a superconducting electromechanical circuit using a commercial titanium-doped lithium niobate modulator. We demonstrate coherent spectroscopy by measuring optomechanically induced transparency and incoherent thermometry by encoding the mechanical sidebands in an optical signal. We also show that our modulators can maintain their room-temperature Pockels coefficient at 800 mK. Further optimization of the modulator design—for example, by using longer waveguides and materials with a higher Pockels coefficient—could reduce the added noise of our setup to similar levels as current semiconductor microwave amplifiers. A commercial titanium-doped lithium niobate phase modulator can be employed at temperatures as low as 800 mK for the electro-optical readout of a superconducting electromechanical circuit at 15 mK.

arXiv:2004.04705•Nature Electronics•May 10, 2021•133 citations

An optically coupled superconducting analog to digital converter

Lewis A. Bunz, R. P. Robertazzi, Sergey V. Rylov

A superconducting analog-to-digital converter has been coupled with a laser diode also operating at 4.2 K to provide a serial output data stream via an optical fiber. The optical signal is converted to a room temperature electrical signal using standard optical fiber receiver techniques. After amplification these signals are fed into a fast comparator circuit. The output of the comparator is a TTL level signal suitable for connection to conventional electronic equipment.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•5 citations

Optical data communication between Josephson-junction circuits and room-temperature electronics

Bart Van Zeghbroeck

The feasibility of optical data transmission to and from Josephson junction circuits, using metal-semiconductor-metal (MSM) photodiodes and GaAs/AlGaAs semiconductor laser diodes with sub-mA threshold current, is demonstrated. Standard devices can be used with the exception of a cooled GaAs detector. It is shown that silicon MSM detectors compatible with Josephson junction circuits can be fabricated. While these detectors show large photoconductive effects at room temperature they behave as good-quality photodiodes at low temperatures. Power dissipation in the laser diode scales with temperature while maintaining the modulation frequency. It is also shown that the combination of a laser diode and a photodiode provides the voltage gain needed to interface Josephson-junction circuits with room-temperature electronics. Experimental results on MSM detectors and laser diodes are presented. Expected power dissipation is below 1 mW per input/output (I/O) at a data rate of 1 Gb/s.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•15 citations

Characterizing All-Optical Biasing and Readout of a Superconducting Opto-Electronic Circuit

Frederik Thiele, Thomas R. Hummel, Julian Brockmeier +6 more

Superconducting nanowire single-photon detectors have become indispensable for experiments in quantum optics and photonic quantum information processing. Nevertheless, these detectors require temperatures below 4 K to operate. These devices typically require coaxial cables as electrical connections for biasing and readout. Replacing these electrical connections with optical fibers both isolates the SNSPD from noise in room-temperature control electronics and simultaneously achieves a connection with a low thermal load. Nevertheless, the optoelectronic interfaces required for this purpose must be fully compatible with the cryogenic operating conditions of the detector. Recently, optical readout of an SNSPD using an electro-optic modulator at cryogenic temperatures has been demonstrated [1]–[3]. In addition, we have shown an opto-electronic bias of an SNSPD by generating the bias current using a photodiode co-located on the cold stage of the cryostat [4]. Both methods replace elements of electrical connection for the SNSPD in the cryostat by an optical fiber. Here, we show the combination of the opto-electronic bias and optical read readout in a single device, which enables us to operate an SNSPD fully isolated from room temperature electronics.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 26, 2023•0 citations

Cryogenic integrated optical modulators for classical and quantum computing

Paolo Pintus, Anshuman Singh, Leonardo Ranzani +11 more

In recent years, standard CMOS microprocessors have approached their maximum power dissipation per unit area, effectively placing a limit on computational power. This highlights the urgent need to explore alternative technologies. One promising avenue is the use of superconductors, which demonstrate zero resistivity below a critical temperature. However, circuits based on superconductors necessitate the use of cryostats to maintain low temperatures, presenting challenges in data transfer with the room temperature environment. While coaxial cables are often employed for this purpose, they suffer from limited data transfer rates and contribute significantly to heat load. On the contrary, photonics integrated circuits (PICs) coupled with optical fibers present a viable solution. They enable scalable, cost-effective, and power-efficient optical interconnections capable of supporting high data transfer rates while minimizing heat transfer. In this presentation, We will discuss the latest advancements in cryogenic PICs, focusing on their application in interfacing with cryogenic computing systems such as single-flux-quantum logic circuits and superconducting qubits.

Photonic Computing: From Materials and Devices to Systems and Applications•Oct 2, 2024•0 citations
We report successful coupling of electrical signals from low temperature (4.2 K) superconducting circuitry to room temperature electronics using laser diodes coupled to optical fibers. The techniques used rely on laser diodes operating at low temperatures, and on high gain amplifiers placed outside the low temperature environment. A new superconducting driver circuit is used to step-up the low output of these circuits to a seven millivolt level, sufficient to modulate the laser diodes. By properly choosing the laser source, the power dissipated within the cryogenic environment can be maintained below 400 (mu) W, with further improvements easily reached.
Superconducting devices operate at speeds where coaxial copper cables can be a limiting factor. Coaxial cables can limit frequency response and impose significant thermal loading on a cyrogenic system. The high bandwidth of optical fibers and their low thermal conductivity make them good candidates for providing data into and out of superconducting circuits. In this paper, we present the results of our experience in operating photodetectors and laser diodes together with superconducting circuits in the same low temperature (4.2 K) environment. Using these photodetectors, we demonstrate the input of optical signals to an analog superconducting circuit at 6 GHz. Output from a superconducting circuit operating at 500 MHz is fed into a laser diode, and optically coupled to room temperature electronics. By combining these two techniques, we demonstrate a fully operational superconducting shift register with both input and output signals supplied by optical fiber.
A major challenge to the scalability of cryogenic computing platforms is the heat load associated with the growing number of electrical cable connections between the superconducting circuitry and the room-temperature environment. Compared with electrical cables, optical fibres have significantly lower thermal conductivity and are widely used in modern telecommunications. However, optical modulation at cryogenic temperatures remains relatively unexplored. Here we report the cryogenic electro-optical readout of a superconducting electromechanical circuit using a commercial titanium-doped lithium niobate modulator. We demonstrate coherent spectroscopy by measuring optomechanically induced transparency and incoherent thermometry by encoding the mechanical sidebands in an optical signal. We also show that our modulators can maintain their room-temperature Pockels coefficient at 800 mK. Further optimization of the modulator design—for example, by using longer waveguides and materials with a higher Pockels coefficient—could reduce the added noise of our setup to similar levels as current semiconductor microwave amplifiers. A commercial titanium-doped lithium niobate phase modulator can be employed at temperatures as low as 800 mK for the electro-optical readout of a superconducting electromechanical circuit at 15 mK.
The feasibility of optical data transmission to and from Josephson junction circuits, using metal-semiconductor-metal (MSM) photodiodes and GaAs/AlGaAs semiconductor laser diodes with sub-mA threshold current, is demonstrated. Standard devices can be used with the exception of a cooled GaAs detector. It is shown that silicon MSM detectors compatible with Josephson junction circuits can be fabricated. While these detectors show large photoconductive effects at room temperature they behave as good-quality photodiodes at low temperatures. Power dissipation in the laser diode scales with temperature while maintaining the modulation frequency. It is also shown that the combination of a laser diode and a photodiode provides the voltage gain needed to interface Josephson-junction circuits with room-temperature electronics. Experimental results on MSM detectors and laser diodes are presented. Expected power dissipation is below 1 mW per input/output (I/O) at a data rate of 1 Gb/s.>
Superconducting nanowire single-photon detectors have become indispensable for experiments in quantum optics and photonic quantum information processing. Nevertheless, these detectors require temperatures below 4 K to operate. These devices typically require coaxial cables as electrical connections for biasing and readout. Replacing these electrical connections with optical fibers both isolates the SNSPD from noise in room-temperature control electronics and simultaneously achieves a connection with a low thermal load. Nevertheless, the optoelectronic interfaces required for this purpose must be fully compatible with the cryogenic operating conditions of the detector. Recently, optical readout of an SNSPD using an electro-optic modulator at cryogenic temperatures has been demonstrated [1]–[3]. In addition, we have shown an opto-electronic bias of an SNSPD by generating the bias current using a photodiode co-located on the cold stage of the cryostat [4]. Both methods replace elements of electrical connection for the SNSPD in the cryostat by an optical fiber. Here, we show the combination of the opto-electronic bias and optical read readout in a single device, which enables us to operate an SNSPD fully isolated from room temperature electronics.
In recent years, standard CMOS microprocessors have approached their maximum power dissipation per unit area, effectively placing a limit on computational power. This highlights the urgent need to explore alternative technologies. One promising avenue is the use of superconductors, which demonstrate zero resistivity below a critical temperature. However, circuits based on superconductors necessitate the use of cryostats to maintain low temperatures, presenting challenges in data transfer with the room temperature environment. While coaxial cables are often employed for this purpose, they suffer from limited data transfer rates and contribute significantly to heat load. On the contrary, photonics integrated circuits (PICs) coupled with optical fibers present a viable solution. They enable scalable, cost-effective, and power-efficient optical interconnections capable of supporting high data transfer rates while minimizing heat transfer. In this presentation, We will discuss the latest advancements in cryogenic PICs, focusing on their application in interfacing with cryogenic computing systems such as single-flux-quantum logic circuits and superconducting qubits.