Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Low Temperature Physics

Flux-Ramp Modulation for SQUID Multiplexing

John A. B. Mates, K. D. Irwin, Leila R. Vale, Gene C Hilton, J. Gao, Konrad W. Lehnert

Published Feb 6, 2012• 97 citations
Publisher
DOI
10.1007/s10909-012-0518-6

Related papers

Linearized Readout of TES array based on Flux Ramp Modulation for Microwave SQUID Multiplexer

Tomoya Irimatsukawa, Fuminori Hirayama, Akira Sato +9 more

IEICE Technical Report; IEICE Tech. Rep.•Oct 1, 2015•0 citations

Microwave Techniques for SQUID Multiplexing

John A. B. Mates, K. D. Irwin, Leila R. Vale +3 more

Bulletin of the American Physical Society•Mar 8, 2007•0 citations

Flux ramp modulation based hybrid microwave SQUID multiplexer

Constantin Schuster, Mathias Wegner, C. Enss +1 more

We present a hybrid microwave superconducting quantum interference device (SQUID) multiplexer that combines two frequency-division multiplexing techniques to allow multiplexing a given number of cryogenic detectors with only a fraction of frequency encoding resonators. Similar to conventional microwave SQUID multiplexing, our multiplexer relies on inductively coupling non-hysteretic, unshunted rf-SQUIDs to superconducting microwave resonators as well as applying flux ramp modulation for output signal linearization. However, instead of utilizing one resonator per SQUID, we couple multiple SQUIDs to a common readout resonator and encode the SQUID input signals in sidebands of the microwave carrier by varying the flux ramp modulation frequency for each SQUID. We prove the suitability of our approach using a prototype device and argue by means of fundamental information theory that our approach is particularly suited for reading out large cryogenic bolometer arrays.

arXiv:2202.05665•Applied Physics Letters•Apr 18, 2022•5 citations

Dc-SQUID Readout with High Dynamic Range and Intrinsic MHz Frequency-Division Multiplexing Capability

Daniel Richter, A. Fleischmann, C. Enss +1 more

We present a novel dc-SQUID readout scheme that provides linearization of the relation between the input and output signal without using a conventional flux-locked loop circuit. It relies on applying a periodic, sawtooth-shaped magnetic flux signal to the modulation coil of the SQUID to continuously measure the flux-to-voltage SQUID characteristic within each period of the flux ramp. In case that the amplitude and repetition rate of the ramp are chosen such that multiple flux quanta are induced in the SQUID and that the input signal is quasistatic within one period of the flux ramp, the input signal adds a constant magnetic flux offset to the SQUID that leads to a phase shift of the SQUID characteristic being proportional to the input signal. We show that this scheme allows for significantly increasing the dynamic range and that it intrinsically allows for MHz frequency-division SQUID multiplexing.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2019•1 citation

Mixing of Low Frequency Signals on a Resistive SQUID

Б.В. Васильев, G.S. Krivoy

•Jan 1, 1977•0 citations

PHASE MODULATION AND SQUIDS WITH COMPLEX RF CIRCUITS

S. A. Belonogov, Oleg V. Snigirev, S.S. Tinchev +1 more

Radiotekhnika i Elektronika•Jan 1, 1980•0 citations
We present a hybrid microwave superconducting quantum interference device (SQUID) multiplexer that combines two frequency-division multiplexing techniques to allow multiplexing a given number of cryogenic detectors with only a fraction of frequency encoding resonators. Similar to conventional microwave SQUID multiplexing, our multiplexer relies on inductively coupling non-hysteretic, unshunted rf-SQUIDs to superconducting microwave resonators as well as applying flux ramp modulation for output signal linearization. However, instead of utilizing one resonator per SQUID, we couple multiple SQUIDs to a common readout resonator and encode the SQUID input signals in sidebands of the microwave carrier by varying the flux ramp modulation frequency for each SQUID. We prove the suitability of our approach using a prototype device and argue by means of fundamental information theory that our approach is particularly suited for reading out large cryogenic bolometer arrays.
We present a novel dc-SQUID readout scheme that provides linearization of the relation between the input and output signal without using a conventional flux-locked loop circuit. It relies on applying a periodic, sawtooth-shaped magnetic flux signal to the modulation coil of the SQUID to continuously measure the flux-to-voltage SQUID characteristic within each period of the flux ramp. In case that the amplitude and repetition rate of the ramp are chosen such that multiple flux quanta are induced in the SQUID and that the input signal is quasistatic within one period of the flux ramp, the input signal adds a constant magnetic flux offset to the SQUID that leads to a phase shift of the SQUID characteristic being proportional to the input signal. We show that this scheme allows for significantly increasing the dynamic range and that it intrinsically allows for MHz frequency-division SQUID multiplexing.