Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Japanese Journal of Applied Physics

Millimeter Wave Mixing Properties of EuBa 2Cu 3O 7-δ Bicrystal Grain Boundary Junction Arrays

Koji Tsuru, Kazunori Miyahara, Minoru Suzuki

Published Dec 1, 1996• 1 citation
Publisher

Abstract

We report the millimeter wave mixing properties of high-T c superconductor Josephson junction arrays using a waveguide-to-microstrip converter in the 100 GHz frequency range. The junction arrays consist of 3 weak links fabricated from EuBa2Cu3O7-δ thin films grown on an MgO bicrystal substrate. In these junction arrays, Shapiro steps are observed in the presence of 100 GHz irradiation at intervals of 3 times the fundamental step voltage. Millimeter wave mixing with an input local oscillator frequency of 99.142 GHz and an input signal frequency of 99.880 GHz is detected as the IF output at 738 MHz. The IF output power peaks at voltages corresponding to those of the dynamic resistance dV/ dI. A mixing conversion efficiency of -24.1 dB is obtained for a 3-junction array.

DOI
10.1143/jjap.35.6047

Related papers

Millimeter-wave detection by GBJJ using high-T/sub c/ superconducting YBaCuO films

S. Kita, H. Tanabe, Takeshi Kobayashi

Millimeter-wave detection in the heterodyne mixing mode has been carried out using the high-T/sub c/ superconducting GBJJ (grain boundary Josephson junction). The GBJJ was fabricated from high T/sub c/ superconducting Y-Ba-Cu-O films, prepared on YSZ and SrTiO/sub 3/ substrates using an RF sputtering technique. The junction was patterned by chemical wet etching with phosphoric acid solution. The authors carried out experiments in the heterodyne mixing mode for a signal of 35 GHz with local oscillation at 34.97 GHz. The detected IF (intermediate frequency) output power was obtained at a bias voltage lying midway between the zeroth and first Shapiro steps. A mixer conversion efficiency of -15 dB was obtained with a dynamic range of about 20 dB at 35 GHz. This result strongly implies that high-T/sub c/ superconducting GBJJ works well as a detector at millimeter-wave frequencies.>

IEEE Transactions on Magnetics•Mar 1, 1989•16 citations

YBCO microwave grain boundary mixer using a SrTiO/sub 3/ bicrystal substrate

R. Seed, Paul C. Dorsey, Hoton How +2 more

A microwave mixer was patterned on a microstrip transmission line of superconducting YBCO (YBa/sub 2/Cu/sub 3/O/sub 7-x/). The YBCO film was epitaxially laser deposited on a SrTiO/sub 3/ bicrystal substrate. A weak link was constructed by patterning a microbridge in the microstrip at the bicrystal boundary. Microwave signals at 9.000 GHz and 9.941 GHz were applied at the input of the microstrip line. An output intermediate frequency signal was observed at 941 MHz and was detected as the transmitted signal. The microbridge junction, which behaved as a resistively shunted Josephson junction (RSJ), was current biased slightly above the critical current I/sub c/. The mixer conversion loss was measured at the input and output ports of the device package. The mixing efficiency was determined at the device junction. This efficiency was compared with the calculated efficiency determined by numerical solution of the Josephson equation for the weak link junction.>

IEEE Transactions on Magnetics•Nov 1, 1993•4 citations

Broadband detection properties of EuBa/sub 2/Cu/sub 3/O/sub 7-δ/ array junctions

Koji Tsuru, Mineharu Suzuki, Osamu Michikami

We have fabricated EuBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// Josephson junction arrays of two different sizes to improve detection output and microwave coupling between junctions and an rf source. The arrays contain three weak link grain boundary junctions made on an MgO bicrystal substrate. It is demonstrated that both the junction array configuration and smaller junction size are effective in improving microwave coupling and hence in increasing the responsivity. The best responsivity obtained is 1085 V/W for broadband detection at 11.9 GHz.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•2 citations

Planar superconducting YBCO microwave mixer employing an engineered grain boundary weak link junction

R. Seed, Paul C. Dorsey, Hoton How +2 more

A microstrip transmission line was patterned from a superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/ film which was laser deposited on a SrTiO/sub 3/ bicrystal substrate. A microbridge in the microstrip was then patterned at the bicrystal interface to fabricate a superconducting grain boundary junction. Microwave mixing was observed with an input local oscillator frequency of 9.000 GHz, and an input signal frequency of 9.941 GHz. The output signal at 941 MHz was detected as a transmitted signal. The junction was current biased slightly above the critical current I/sub c/. The measured conversion loss was compared to the calculated value based upon a numerical solution of the equation for a superconducting weak link junction.>

IEEE Transactions on Applied Superconductivity•Jan 1, 1994•6 citations

High T/sub c/ superconducting step-edge junctions and their properties in millimeter-wave band

Yijun Feng, L. Kang, X. B. Wang +8 more

Superconducting step-edge junctions were fabricated on step-edges in (100) LaAlO/sub 3/ substrates by sputter-deposited epitaxial YBaCuO and TlBaCaCuO thin films. The substrate steps were patterned by ion beam etching using metal film as a mask. The transport properties of the junctions were characterized by four-probe electrical measurements. The critical current-normal resistance product (I/sub c/R/sub N/) was larger than 0.2 mV (77 K) for most of the junctions. Clear Shapiro steps were observed in the current-voltage characteristics of the junctions with 36 GHz or 95 GHz millimeter-wave irradiation. The high frequency properties of these high T/sub c/ Josephson junctions showed that they were quite suitable for the Josephson harmonic mixer used in the digital phase locked millimeter and sub-millimeter wave sources.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•1 citation

Millimeter Wave Harmonic Mixing in Thin-Film YBa2Cu3O7-x Josephson Junctions

Yoshizumi Yasuoka, Takashi Nozue, Tsutomu Yamashita

Harmonic mixing characteristics in thin-film YBa2Cu3O7-x (YBCO) Josephson junctions fabricated using photolithography were examined at the liquid nitrogen temperature (77 K) using 94 GHz millimeter wave radiation. As a result, a mixing signal (IF output) was obtained up to the harmonic number of 55 in harmonic mixing using the local oscillation (LO) wave as the microwave. The output strongly depended on the power of the LO and signal waves, and on the Shapiro step spacing induced by the LO wave. The IF output decreased in proportion to N -2 in the lower harmonic number region. However, the rate of decrease increased with an increase in the harmonic number.

Japanese Journal of Applied Physics•Nov 1, 1999•2 citations
We report the millimeter wave mixing properties of high-T c superconductor Josephson junction arrays using a waveguide-to-microstrip converter in the 100 GHz frequency range. The junction arrays consist of 3 weak links fabricated from EuBa2Cu3O7-δ thin films grown on an MgO bicrystal substrate. In these junction arrays, Shapiro steps are observed in the presence of 100 GHz irradiation at intervals of 3 times the fundamental step voltage. Millimeter wave mixing with an input local oscillator frequency of 99.142 GHz and an input signal frequency of 99.880 GHz is detected as the IF output at 738 MHz. The IF output power peaks at voltages corresponding to those of the dynamic resistance dV/ dI. A mixing conversion efficiency of -24.1 dB is obtained for a 3-junction array.
Millimeter-wave detection in the heterodyne mixing mode has been carried out using the high-T/sub c/ superconducting GBJJ (grain boundary Josephson junction). The GBJJ was fabricated from high T/sub c/ superconducting Y-Ba-Cu-O films, prepared on YSZ and SrTiO/sub 3/ substrates using an RF sputtering technique. The junction was patterned by chemical wet etching with phosphoric acid solution. The authors carried out experiments in the heterodyne mixing mode for a signal of 35 GHz with local oscillation at 34.97 GHz. The detected IF (intermediate frequency) output power was obtained at a bias voltage lying midway between the zeroth and first Shapiro steps. A mixer conversion efficiency of -15 dB was obtained with a dynamic range of about 20 dB at 35 GHz. This result strongly implies that high-T/sub c/ superconducting GBJJ works well as a detector at millimeter-wave frequencies.>
A microwave mixer was patterned on a microstrip transmission line of superconducting YBCO (YBa/sub 2/Cu/sub 3/O/sub 7-x/). The YBCO film was epitaxially laser deposited on a SrTiO/sub 3/ bicrystal substrate. A weak link was constructed by patterning a microbridge in the microstrip at the bicrystal boundary. Microwave signals at 9.000 GHz and 9.941 GHz were applied at the input of the microstrip line. An output intermediate frequency signal was observed at 941 MHz and was detected as the transmitted signal. The microbridge junction, which behaved as a resistively shunted Josephson junction (RSJ), was current biased slightly above the critical current I/sub c/. The mixer conversion loss was measured at the input and output ports of the device package. The mixing efficiency was determined at the device junction. This efficiency was compared with the calculated efficiency determined by numerical solution of the Josephson equation for the weak link junction.>
We have fabricated EuBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// Josephson junction arrays of two different sizes to improve detection output and microwave coupling between junctions and an rf source. The arrays contain three weak link grain boundary junctions made on an MgO bicrystal substrate. It is demonstrated that both the junction array configuration and smaller junction size are effective in improving microwave coupling and hence in increasing the responsivity. The best responsivity obtained is 1085 V/W for broadband detection at 11.9 GHz.>
A microstrip transmission line was patterned from a superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/ film which was laser deposited on a SrTiO/sub 3/ bicrystal substrate. A microbridge in the microstrip was then patterned at the bicrystal interface to fabricate a superconducting grain boundary junction. Microwave mixing was observed with an input local oscillator frequency of 9.000 GHz, and an input signal frequency of 9.941 GHz. The output signal at 941 MHz was detected as a transmitted signal. The junction was current biased slightly above the critical current I/sub c/. The measured conversion loss was compared to the calculated value based upon a numerical solution of the equation for a superconducting weak link junction.>
Superconducting step-edge junctions were fabricated on step-edges in (100) LaAlO/sub 3/ substrates by sputter-deposited epitaxial YBaCuO and TlBaCaCuO thin films. The substrate steps were patterned by ion beam etching using metal film as a mask. The transport properties of the junctions were characterized by four-probe electrical measurements. The critical current-normal resistance product (I/sub c/R/sub N/) was larger than 0.2 mV (77 K) for most of the junctions. Clear Shapiro steps were observed in the current-voltage characteristics of the junctions with 36 GHz or 95 GHz millimeter-wave irradiation. The high frequency properties of these high T/sub c/ Josephson junctions showed that they were quite suitable for the Josephson harmonic mixer used in the digital phase locked millimeter and sub-millimeter wave sources.>
Harmonic mixing characteristics in thin-film YBa2Cu3O7-x (YBCO) Josephson junctions fabricated using photolithography were examined at the liquid nitrogen temperature (77 K) using 94 GHz millimeter wave radiation. As a result, a mixing signal (IF output) was obtained up to the harmonic number of 55 in harmonic mixing using the local oscillation (LO) wave as the microwave. The output strongly depended on the power of the LO and signal waves, and on the Shapiro step spacing induced by the LO wave. The IF output decreased in proportion to N -2 in the lower harmonic number region. However, the rate of decrease increased with an increase in the harmonic number.