Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Study of Low-Frequency Noise Performance of Nanobridge-Based SQUIDs in External Magnetic Fields

S. Rozhko, T. Hino, A. Blois, L. Hao, John C. Gallop, David Cox, Edward J. Romans

Published Dec 11, 2012• 6 citations
Publisher

Abstract

We report on the low-frequency noise performance of niobium dc superconducting quantum interference devices (SQUIDs), which contain nanobridges fabricated by focused ion beam lithography as the active Josephson elements. The devices have feature sizes down to 70 nm. We have measured devices of different loop sizes in two readout configurations: nano-scale loop sizes in small signal mode using a series SQUID array as a low-temperature pre-amplifier, and larger micron-scale loop sizes in a conventional flux-locked loop. We investigate the different contributions to the low frequency noise and report on electrical measurements made in applied magnetic fields of up to 0.5 T (in-plane) and 0.1 T (perpendicular to the plane) at operating temperatures around 7 K. We compare the measurements with the existing theories of noise in a dc SQUID.

DOI
10.1109/tasc.2012.2233537

Related papers

Flux noise in ion-implanted nanoSQUIDs

Giuseppe Carlo Tettamanzi, Chris I. Pakes, S. K. H. Lam +1 more

Focused ion-beam (FIB) technology has been used to fabricate miniature Nb DC SQUIDs (superconducting quantum interference devices) which incorporate resistively shunted microbridge junctions and a central loop with a hole diameter ranging from 1058 to 50 nm. The smallest device, with a 50 nm hole diameter, has a white flux noise level of 2.6 µΦ 0 Hz −1/2 at 10 4 Hz. The scaling of the flux noise properties and focusing effect of the SQUID with the hole size were examined. The observed low frequency flux noises of different devices were compared with the contribution due to the spin fluctuation of defects introduced during FIB processing and of thermally activated flux hopping in the SQUID washer.

arXiv:1003.5436•Superconductor Science and Technology•May 14, 2009•11 citations

Ultra low noise Nb DC SQUIDs

Richard F. Voss, Robert B. Laibowitz, Alec Nigel Broers +3 more

Electron-beam lithography has been used to produce ultra low noise Nb dc SQUIDs (Superconducting QUantum Interference Devices) with Josephson elements consisting of either small area tunnel junctions or very narrow variable thickness bridges (nanobridges). Detailed voltage noise and transfer function measurements have been made as a function of temperature and flux and current bias. These measurements allow a computation of the intrinsic energy resolution ε vs bias parameters as well as comparison with models of intrinsic SQUID noise. The best ε obtained was of order Planck's constant h. Moreover, the detailed characteristics of the SQUID voltage noise are in agreement with a small signal analysis that depends only on the current noise in each of the Josephson elements and measurable parameters.

IEEE Transactions on Magnetics•Jan 1, 1981•48 citations

Noise properties of SQUIDs made from nanobridges

S. K. H. Lam

For the fabrication of nanoscale SQUIDs, for example having loop diameters of order 1 µm or smaller, the conventional trilayer window-type Josephson junctions are too large. Instead, we consider the use of nanobridge junctions with dimensions of order 100 nm. The problem of hysteresis in the junctions' current–voltage characteristic (IVC) is avoided by depositing a gold overlayer, which serves as both a thermal and electrical shunt. Noise measurement of dc SQUIDs which incorporate such Nb nanobridges as the Josephson junctions are reported. Devices having different IVCs were fabricated and characterized. The best device has a flux noise of 5 × 10 −6 Φ 0 Hz −1/2 at 4.2 K, and there is no significant increase in the noise level in a static magnetic field up to 2 mT. Techniques for increasing the voltage modulation depth, and hence improving the flux noise performance, are discussed.

Superconductor Science and Technology•Aug 7, 2006•30 citations

An integrated superconductive magnetic nanosensor for high-sensitivity nanoscale applications

C. Granata, E. Esposito, Antonio Vettoliere +2 more

An integrated magnetic nanosensor based on a niobium dc SQUID (superconducting quantum interference device) for nanoscale applications is presented. The sensor, having a washer shape with a hole of 200 nm and two Josephson-Dayem nanobridges of 80 nm × 100 nm, consists of a Nb(30 nm)/Al(30 nm) bilayer patterned by electron beam lithography (EBL) and shaped by lift-off and reactive ion etch (RIE) processes. The presence of the niobium coils, integrated on-chip and tightly coupled to the SQUID, allows us to easily excite the sensor in order to get the voltage-flux characteristics and to flux bias the SQUID at its optimal point. The measurements were performed at liquid helium temperature. A voltage swing of 75 µV and a maximum voltage-flux transfer coefficient (responsivity) as high as 1 mV/Φ(0) were directly measured from the voltage-flux characteristic. The noise measurements were performed in open loop mode, biasing the SQUID with a dc magnetic flux at its maximum responsivity point and using direct-coupled low-noise readout electronics. A white magnetic flux noise spectral density as low as 2.5 μΦ(0) Hz(-1/2) was achieved, corresponding to a magnetization or spin sensitivity in units of the Bohr magneton of 100 spin Hz(-1/2). Possible applications of this nanosensor can be envisaged in magnetic detection of nanoparticles and small clusters of atoms and molecules, in the measurement of nanoobject magnetization, and in quantum computing.

Nanotechnology•May 27, 2008•82 citations

Very low noise, tightly coupled, dc SQUID amplifiers

B. Muhlfelder, J. A. Beall, Michael W. Cromar +1 more

We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.

Applied Physics Letters•Oct 27, 1986•19 citations

NANO-SQUIDs based on niobium Dayem bridges for nanoscale applications

C. Granata, Antonio Vettoliere, Pravin S. Walke +5 more

We report on the design, the fabrication and the performance of an integrated magnetic nano-sensor based on niobium dc-SQUID (Superconducting QUantum Interference Device) for nanoscale applications is presented. The nano-sensors are based on nanometric niobium constrictions (Dayem bridges) inserted in a square loop having a side length of 200 nm. Measurements of voltage-flux characteristic, flux to voltage transfer factor and noise performances are reported. In small signal mode, the sensors have shown a magnetic flux noise spectral density of 1.5 μΦ 0 /Hz 1/2 corresponding to a spin sensitivity in unit of Bohr magneton of 60 spin/Hz 1/2 . Supercurrent decay measurements of these devices are also reported. Such measurements provide useful information for applications which employ the SQUID as a trigger where the sensor works on the zero voltage state. The experimental data, have shown an intrinsic current fluctuation less than 0.2% of the critical current at liquid helium temperature, corresponding to an intrinsic sensor magnetic flux resolution of a few mΦ 0 . In view of the nano-SQUID employments in the detection of small spin populations, the authors calculated the spin sensitivity and the magnetic response relative to the single spin, as a function of its position within the SQUID hole. The results show that the SQUID response depends strongly on the spin position.

Journal of Physics Conference Series•Jun 1, 2010•5 citations
We report on the low-frequency noise performance of niobium dc superconducting quantum interference devices (SQUIDs), which contain nanobridges fabricated by focused ion beam lithography as the active Josephson elements. The devices have feature sizes down to 70 nm. We have measured devices of different loop sizes in two readout configurations: nano-scale loop sizes in small signal mode using a series SQUID array as a low-temperature pre-amplifier, and larger micron-scale loop sizes in a conventional flux-locked loop. We investigate the different contributions to the low frequency noise and report on electrical measurements made in applied magnetic fields of up to 0.5 T (in-plane) and 0.1 T (perpendicular to the plane) at operating temperatures around 7 K. We compare the measurements with the existing theories of noise in a dc SQUID.
Focused ion-beam (FIB) technology has been used to fabricate miniature Nb DC SQUIDs (superconducting quantum interference devices) which incorporate resistively shunted microbridge junctions and a central loop with a hole diameter ranging from 1058 to 50 nm. The smallest device, with a 50 nm hole diameter, has a white flux noise level of 2.6 µΦ 0 Hz −1/2 at 10 4 Hz. The scaling of the flux noise properties and focusing effect of the SQUID with the hole size were examined. The observed low frequency flux noises of different devices were compared with the contribution due to the spin fluctuation of defects introduced during FIB processing and of thermally activated flux hopping in the SQUID washer.
Electron-beam lithography has been used to produce ultra low noise Nb dc SQUIDs (Superconducting QUantum Interference Devices) with Josephson elements consisting of either small area tunnel junctions or very narrow variable thickness bridges (nanobridges). Detailed voltage noise and transfer function measurements have been made as a function of temperature and flux and current bias. These measurements allow a computation of the intrinsic energy resolution ε vs bias parameters as well as comparison with models of intrinsic SQUID noise. The best ε obtained was of order Planck's constant h. Moreover, the detailed characteristics of the SQUID voltage noise are in agreement with a small signal analysis that depends only on the current noise in each of the Josephson elements and measurable parameters.
For the fabrication of nanoscale SQUIDs, for example having loop diameters of order 1 µm or smaller, the conventional trilayer window-type Josephson junctions are too large. Instead, we consider the use of nanobridge junctions with dimensions of order 100 nm. The problem of hysteresis in the junctions' current–voltage characteristic (IVC) is avoided by depositing a gold overlayer, which serves as both a thermal and electrical shunt. Noise measurement of dc SQUIDs which incorporate such Nb nanobridges as the Josephson junctions are reported. Devices having different IVCs were fabricated and characterized. The best device has a flux noise of 5 × 10 −6 Φ 0 Hz −1/2 at 4.2 K, and there is no significant increase in the noise level in a static magnetic field up to 2 mT. Techniques for increasing the voltage modulation depth, and hence improving the flux noise performance, are discussed.
An integrated magnetic nanosensor based on a niobium dc SQUID (superconducting quantum interference device) for nanoscale applications is presented. The sensor, having a washer shape with a hole of 200 nm and two Josephson-Dayem nanobridges of 80 nm × 100 nm, consists of a Nb(30 nm)/Al(30 nm) bilayer patterned by electron beam lithography (EBL) and shaped by lift-off and reactive ion etch (RIE) processes. The presence of the niobium coils, integrated on-chip and tightly coupled to the SQUID, allows us to easily excite the sensor in order to get the voltage-flux characteristics and to flux bias the SQUID at its optimal point. The measurements were performed at liquid helium temperature. A voltage swing of 75 µV and a maximum voltage-flux transfer coefficient (responsivity) as high as 1 mV/Φ(0) were directly measured from the voltage-flux characteristic. The noise measurements were performed in open loop mode, biasing the SQUID with a dc magnetic flux at its maximum responsivity point and using direct-coupled low-noise readout electronics. A white magnetic flux noise spectral density as low as 2.5 μΦ(0) Hz(-1/2) was achieved, corresponding to a magnetization or spin sensitivity in units of the Bohr magneton of 100 spin Hz(-1/2). Possible applications of this nanosensor can be envisaged in magnetic detection of nanoparticles and small clusters of atoms and molecules, in the measurement of nanoobject magnetization, and in quantum computing.
We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.
We report on the design, the fabrication and the performance of an integrated magnetic nano-sensor based on niobium dc-SQUID (Superconducting QUantum Interference Device) for nanoscale applications is presented. The nano-sensors are based on nanometric niobium constrictions (Dayem bridges) inserted in a square loop having a side length of 200 nm. Measurements of voltage-flux characteristic, flux to voltage transfer factor and noise performances are reported. In small signal mode, the sensors have shown a magnetic flux noise spectral density of 1.5 μΦ 0 /Hz 1/2 corresponding to a spin sensitivity in unit of Bohr magneton of 60 spin/Hz 1/2 . Supercurrent decay measurements of these devices are also reported. Such measurements provide useful information for applications which employ the SQUID as a trigger where the sensor works on the zero voltage state. The experimental data, have shown an intrinsic current fluctuation less than 0.2% of the critical current at liquid helium temperature, corresponding to an intrinsic sensor magnetic flux resolution of a few mΦ 0 . In view of the nano-SQUID employments in the detection of small spin populations, the authors calculated the spin sensitivity and the magnetic response relative to the single spin, as a function of its position within the SQUID hole. The results show that the SQUID response depends strongly on the spin position.