Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Measurements of device parameters on large arrays of Josephson interferometers

S. Basavaiah, J. H. Greiner, H. H. Zappe, Sherwin J. Singer

Published Mar 1, 1980• 13 citations
Publisher

Abstract

Measurements on large arrays of Josephson interferometers were carried out to obtain individual device parameters and their spread. Each array contained 784 identical interferometers with junction diameters of 5 and 7 μm and was deposited on a 6.35×6.35-mm Si chip. Threshold currents Im(0), subgap resistances Rj, and Vm —the product of Rj and Im(0) —were investigated. Statistical analysis indicated that the standard deviation σ of Im(0) and Rj ranged between 6 and 18% and that of Vm ranged between 5 and 7%. A systematic spatial dependence of Im(0) and Rj on the chips was obtained which is attributed as being due to nonuniformities in the rf oxygen discharge used to form the tunnel barrier. With improvements in the process, namely, eliminating these nonuniformities, the standard deviation in Im(0) (and Rj) can be reduced to about 5%. From the observed variations in the junction areas it is estimated that the random variation in the Josephson current density is about 4%. Large scale applications of these interferometers in the design of computer memory and logic thus seem feasible.

DOI
10.1063/1.327779

Related papers

Studies on arrays of Josephson tunnel junction interferometers

Ronald F. Broom, Theodor O. Mohr

Josephson-junction interferometers have previously been proposed as memory devices in which information is stored as a single flux quantum, (SFQ). To investigate the feasibility of making large arrays of SFQ cells suitable for the memory of a cryogenic computer, arrays containing 80 interferometers have been made and measured. The prime objective was to determine the distribution of the dc Josephson current i1 within the arays and to compare it with the design value required for successful operation of all cells in high density arrays. The results show that a substantial fraction of the arrays has standard deviations in i1 less than the maximum allowable, thus demonstrating for the first time that such a memory can be made with present technology. The fabrication, measurement technique and a detailed analysis of the current distributions on the arrays are presented.

Journal of Vacuum Science and Technology•May 1, 1978•8 citations

Improving Josephson junction reproducibility for superconducting quantum circuits: junction area fluctuation

Anastasiya A. Pishchimova, Nikita S. Smirnov, Daria A. Moskaleva +6 more

Abstract Josephson superconducting qubits and parametric amplifiers are prominent examples of superconducting quantum circuits that have shown rapid progress in recent years. As such devices become more complex, the requirements for reproducibility of their electrical properties across a chip are being tightened. Critical current of the Josephson junction Ic is the essential electrical parameter in a chip. So, its variation is to be minimized. According to the Ambegaokar–Baratoff formula, critical current is related to normal-state resistance, which can be measured at room temperature. In this study, we focused on the dominant source of non-uniformity for the Josephson junction critical current–junction area variation. We optimized Josephson junction fabrication process and demonstrated resistance variation of 9.8–4.4% and 4.8–2.3% across 22 × 22 mm2 and 5 × 10 mm2 chip areas, respectively. For a wide range of junction areas from 0.008 to 0.12 μm2, we ensure a small linewidth standard deviation of 4 nm measured over 4500 junctions with linear dimensions from 80 to 680 nm. We found that the dominate source of junction area variation limiting $${\mathrm{I}}_{\mathrm{c}}$$ I c reproducibility is the imperfection of the evaporation system. The developed fabrication process was tested on superconducting highly coherent transmon qubits (T1 > 100 μs) and a nonlinear asymmetric inductive element parametric amplifier.

arXiv:2210.15293•Scientific Reports•Apr 25, 2023•46 citations

Niobium nitride Josephson junction process development

James M. Murduck, J. DiMond, C.Y. Dang +1 more

NbN/MgO/NbN tunnel junction fabrication has been developed using statistical experimental design for insertion into a Josephson LSI (large-scale integration) fabrication technology. Junction deposition conditions have been studied and correlated with structural characterization and junction I-V measurements. Josephson junctions with sum gaps as large as 5.0 mV and junction quality factor of 47 mV have been produced. Current density uniformity, a critical parameter in circuit design, has also been investigated. I/sub c/(O) uniformity at 4.2 K of a 4000 junction array was within sigma =3.1% and was +or-10% across 1 in/sup 2/. The utility of this junction process has been demonstrated by insertion into a standard circuit fabrication process that has produced logic circuit operation above 10 K.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•7 citations

Temperature-dependent properties of niobium nitride Josephson tunnel junctions

Alexandre Shoji, Masahiro Aoyagi, S. Kosaka +1 more

We report the electrical properties of all niobium nitride(NbN) Josephson tunnel junctions with magnesium oxide(MgO) films as barriers in the temperature range 4.2-15 K. NbN/MgO/NbN Josephson tunnel junctions have large gap voltages(Vg=4.8-5.4 mV), large products of the maximum critical currents and the normal tunneling resistances(IcRn=3.15-3.35 mV), and small subgap leakage currents(Vm=13-138 mV) at 4.2 K. The junction parameters decreased with increase in temperature, but reasonably large junction parameters(for example, Vg=4.9 mV, IcRn=2.67 mV, and Vm=22 mV) have been obtained even at 9 K. The magnetic penetration depth in NbN electrodes has been measured up to 15 K using two-junction interferometers which consist of NbN/MgO/NbN junctions, NbN ground planes, and NbN control lines.

IEEE Transactions on Magnetics•Mar 1, 1987•52 citations

Sub-micrometer epitaxial Josephson junctions for quantum circuits

Jeffrey S Kline, Michael R. Vissers, Fabio C S da Silva +11 more

We present a fabrication scheme and testing results for epitaxial sub-micrometer Josephson junctions. The junctions are made using a high-temperature (1170 K) "via process" yielding junctions as small as 0.8 mu m in diameter by use of optical lithography. Sapphire (Al2O3) tunnel-barriers are grown on an epitaxial Re/Ti multilayer base-electrode. We have fabricated devices with both Re and Al top electrodes. While room-temperature (295 K) resistance versus area data are favorable for both types of top electrodes, the low-temperature (50 mK) data show that junctions with the Al top electrode have a much higher subgap resistance. The microwave loss properties of the junctions have been measured by use of superconducting Josephson junction qubits. The results show that high subgap resistance correlates to improved qubit performance.

arXiv:1108.1830•Superconductor Science and Technology•Dec 22, 2011•16 citations

Improving wafer-scale Josephson junction resistance variation in superconducting quantum coherent circuits

John Mark Kreikebaum, Kevin P. O’Brien, Alexis Morvan +1 more

Abstract Quantum bits, or qubits, are an example of coherent circuits envisioned for next-generation computers and detectors. A robust superconducting qubit with a coherent lifetime of O(100 µs) is the transmon: a Josephson junction functioning as a non-linear inductor shunted with a capacitor to form an anharmonic oscillator. In a complex device with many such transmons, precise control over each qubit frequency is often required, and thus variations of the junction area and tunnel barrier thickness must be sufficiently minimized to achieve optimal performance while avoiding spectral overlap between neighboring circuits. Simply transplanting our recipe optimized for single, stand-alone devices to wafer-scale (producing 64, 1x1 cm dies from a 150 mm wafer) initially resulted in global drifts in room-temperature tunneling resistance of ± 30%. Inferring a critical current I c variation from this resistance distribution, we present an optimized process developed from a systematic 38 wafer study that results in < 3.5% relative standard deviation (RSD) in critical current ( ≡ σ I c / I c ) for 3000 Josephson junctions (both single-junctions and asymmetric SQUIDs) across an area of 49 cm2. Looking within a 1x1 cm moving window across the substrate gives an estimate of the variation characteristic of a given qubit chip. Our best process, utilizing ultrasonically assisted development, uniform ashing, and dynamic oxidation has shown σ I c / I c = 1.8% within 1x1 cm, on average, with a few 1x1 cm areas having σ I c / I c < 1.0% (equivalent to σ f / f < 0.5%). Such stability would drastically improve the yield of multi-junction chips with strict critical current requirements.

arXiv:1909.09165•Superconductor Science and Technology•Apr 29, 2020•145 citations
Measurements on large arrays of Josephson interferometers were carried out to obtain individual device parameters and their spread. Each array contained 784 identical interferometers with junction diameters of 5 and 7 μm and was deposited on a 6.35×6.35-mm Si chip. Threshold currents Im(0), subgap resistances Rj, and Vm —the product of Rj and Im(0) —were investigated. Statistical analysis indicated that the standard deviation σ of Im(0) and Rj ranged between 6 and 18% and that of Vm ranged between 5 and 7%. A systematic spatial dependence of Im(0) and Rj on the chips was obtained which is attributed as being due to nonuniformities in the rf oxygen discharge used to form the tunnel barrier. With improvements in the process, namely, eliminating these nonuniformities, the standard deviation in Im(0) (and Rj) can be reduced to about 5%. From the observed variations in the junction areas it is estimated that the random variation in the Josephson current density is about 4%. Large scale applications of these interferometers in the design of computer memory and logic thus seem feasible.
Josephson-junction interferometers have previously been proposed as memory devices in which information is stored as a single flux quantum, (SFQ). To investigate the feasibility of making large arrays of SFQ cells suitable for the memory of a cryogenic computer, arrays containing 80 interferometers have been made and measured. The prime objective was to determine the distribution of the dc Josephson current i1 within the arays and to compare it with the design value required for successful operation of all cells in high density arrays. The results show that a substantial fraction of the arrays has standard deviations in i1 less than the maximum allowable, thus demonstrating for the first time that such a memory can be made with present technology. The fabrication, measurement technique and a detailed analysis of the current distributions on the arrays are presented.
Abstract Josephson superconducting qubits and parametric amplifiers are prominent examples of superconducting quantum circuits that have shown rapid progress in recent years. As such devices become more complex, the requirements for reproducibility of their electrical properties across a chip are being tightened. Critical current of the Josephson junction Ic is the essential electrical parameter in a chip. So, its variation is to be minimized. According to the Ambegaokar–Baratoff formula, critical current is related to normal-state resistance, which can be measured at room temperature. In this study, we focused on the dominant source of non-uniformity for the Josephson junction critical current–junction area variation. We optimized Josephson junction fabrication process and demonstrated resistance variation of 9.8–4.4% and 4.8–2.3% across 22 × 22 mm2 and 5 × 10 mm2 chip areas, respectively. For a wide range of junction areas from 0.008 to 0.12 μm2, we ensure a small linewidth standard deviation of 4 nm measured over 4500 junctions with linear dimensions from 80 to 680 nm. We found that the dominate source of junction area variation limiting Ic{\mathrm{I}}_{\mathrm{c}}Ic​ I c reproducibility is the imperfection of the evaporation system. The developed fabrication process was tested on superconducting highly coherent transmon qubits (T1 > 100 μs) and a nonlinear asymmetric inductive element parametric amplifier.
NbN/MgO/NbN tunnel junction fabrication has been developed using statistical experimental design for insertion into a Josephson LSI (large-scale integration) fabrication technology. Junction deposition conditions have been studied and correlated with structural characterization and junction I-V measurements. Josephson junctions with sum gaps as large as 5.0 mV and junction quality factor of 47 mV have been produced. Current density uniformity, a critical parameter in circuit design, has also been investigated. I/sub c/(O) uniformity at 4.2 K of a 4000 junction array was within sigma =3.1% and was +or-10% across 1 in/sup 2/. The utility of this junction process has been demonstrated by insertion into a standard circuit fabrication process that has produced logic circuit operation above 10 K.>
We report the electrical properties of all niobium nitride(NbN) Josephson tunnel junctions with magnesium oxide(MgO) films as barriers in the temperature range 4.2-15 K. NbN/MgO/NbN Josephson tunnel junctions have large gap voltages(Vg=4.8-5.4 mV), large products of the maximum critical currents and the normal tunneling resistances(IcRn=3.15-3.35 mV), and small subgap leakage currents(Vm=13-138 mV) at 4.2 K. The junction parameters decreased with increase in temperature, but reasonably large junction parameters(for example, Vg=4.9 mV, IcRn=2.67 mV, and Vm=22 mV) have been obtained even at 9 K. The magnetic penetration depth in NbN electrodes has been measured up to 15 K using two-junction interferometers which consist of NbN/MgO/NbN junctions, NbN ground planes, and NbN control lines.
We present a fabrication scheme and testing results for epitaxial sub-micrometer Josephson junctions. The junctions are made using a high-temperature (1170 K) "via process" yielding junctions as small as 0.8 mu m in diameter by use of optical lithography. Sapphire (Al2O3) tunnel-barriers are grown on an epitaxial Re/Ti multilayer base-electrode. We have fabricated devices with both Re and Al top electrodes. While room-temperature (295 K) resistance versus area data are favorable for both types of top electrodes, the low-temperature (50 mK) data show that junctions with the Al top electrode have a much higher subgap resistance. The microwave loss properties of the junctions have been measured by use of superconducting Josephson junction qubits. The results show that high subgap resistance correlates to improved qubit performance.
Abstract Quantum bits, or qubits, are an example of coherent circuits envisioned for next-generation computers and detectors. A robust superconducting qubit with a coherent lifetime of O(100 µs) is the transmon: a Josephson junction functioning as a non-linear inductor shunted with a capacitor to form an anharmonic oscillator. In a complex device with many such transmons, precise control over each qubit frequency is often required, and thus variations of the junction area and tunnel barrier thickness must be sufficiently minimized to achieve optimal performance while avoiding spectral overlap between neighboring circuits. Simply transplanting our recipe optimized for single, stand-alone devices to wafer-scale (producing 64, 1x1 cm dies from a 150 mm wafer) initially resulted in global drifts in room-temperature tunneling resistance of ± 30%. Inferring a critical current I c variation from this resistance distribution, we present an optimized process developed from a systematic 38 wafer study that results in < 3.5% relative standard deviation (RSD) in critical current ( ≡ σ I c / I c ) for 3000 Josephson junctions (both single-junctions and asymmetric SQUIDs) across an area of 49 cm2. Looking within a 1x1 cm moving window across the substrate gives an estimate of the variation characteristic of a given qubit chip. Our best process, utilizing ultrasonically assisted development, uniform ashing, and dynamic oxidation has shown σ I c / I c = 1.8% within 1x1 cm, on average, with a few 1x1 cm areas having σ I c / I c < 1.0% (equivalent to σ f / f < 0.5%). Such stability would drastically improve the yield of multi-junction chips with strict critical current requirements.