Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Closed system fabrication of Josephson tunnel junctions

Gert K. G. Hohenwarter, J.E. Nordman

Published Mar 1, 1982• 7 citations
Publisher

Abstract

A technique for the fabrication of Josephson tunnel junctions without breaking vacuum and without the use of masks is presented. No chemical processing is done on either of the junction electrode surfaces. Hence, no chemical or reactive cleaning is required before the formation of the tunneling barrier. Nevertheless, standard photolithography and chemical or plasma etching can be employed for defining patterns. I-V characteristics of Nb-NbOx-Pb junctions fabricated by this method have not exhibited a ’’knee’’ at the onset of the quasiparticle current.

DOI
10.1063/1.93098

Related papers

Nb/Nb oxide/Pb-alloy Josephson tunnel junctions

Stanley I. Raider, R.E. Drake

A procedure is described for fabricating thin film Nb/Nb oxide/Pb-alloy Josephson tunnel junctions that satisfies the principal requirements for integrated circuit design and fabrication. A deposited Nb film, evaporated from an e-gun heated source, was patterned by chemical etching to form a base electrode. A junction was completed by plasma etching and plasma oxidizing the Nb junction area to form a tunnel barrier and by depositing a Pb alloy counterelectrode. Josephson tunnel junctions with Nb/Nb oxide/Pb-Au-In structures were prepared with low excess subgap currents in the current-voltage (I-V) curve and with reproducible and stable I-V characteristics. Variations in junction current density from run-run were ± 15%. Seven 3-junction interferomeeters out of a population of 50,000 were shorted (99.99% yield) for causes not immediately attributable to photoresist-related defects. No changes in Josephson current were detected after thermal cycling 17,000 interferometers 1,800 × between room temperature and 4.2°K, after storing them for 2 years at 5°C, or after annealing 5,000 interferometers for 4.5 hours at 70°C.

IEEE Transactions on Magnetics•Jan 1, 1981•41 citations

New fabrication process for Josephson tunnel junctions with (niobium nitride, niobium) double-layered electrodes

Akira Shoji, Fujitoshi Shinoki, S. Kosaka +2 more

All hard Josephson tunnel junctions, whose base and counter electrodes are composed of double-layered niobium nitride (NbN) and niobium (Nb) films, have been successfully fabricated by isolating a junction sandwich formed on a whole silicon wafer with a reactive ion etching technique. The reactive ion etching technique has been used for patterning both base and counterelectrodes, and self-aligning definition of junction areas has been performed. The fabricated junctions show good quality single-particle tunneling characteristics and excellent uniformity in critical currents.

Applied Physics Letters•Dec 1, 1982•72 citations

Fabrication of NbN/Pb Josephson tunnel junctions with a novel integration method

S. Kosaka, Fujitoshi Shinoki, S. Takada +1 more

We have developed a new integration method for Josephson tunnel junctions based on high Tc superconducting compound materials such as NbN. In this method, a sputtered ZnO film has been employed as a resist mask which can be used in high substrate temperatures during the film deposition. It has been found that fine patterns of the refractory superconducting film can be obtained by this method and the patterning processes have no interference with other integration processes. We have applied this method to patterning base electrode of NbN and formed high quality NbN-oxide-Pb Josephson tunnel junctions by using an rf plasma oxidation. The fabricated junctions have been found to have a relatively large gap ( ∼ 4.0 mV ) and low current leak in the subgap region, and to be quite stable for thermal cyclings and storage. We have also fabricated quantum interference memory devices by integrating these junctions and the operation has been successfully demonstrated.

IEEE Transactions on Magnetics•Jan 1, 1981•24 citations

All refractory Josephson tunnel junctions fabricated by reactive ion etching

Alexandre Shoji, S. Kosaka, Fujitoshi Shinoki +2 more

We have developed a novel process for fabricating all refractory Josephson tunnel junctions whose base and counter electrodes are composed of (Nb-NbN) double-layered films. In this process, tunnel junctions have been isolated using a reactive ion etching from a junction sandwich which had been formed on an entire silicon wafer, and also the reactive ion etching has been used for patterning electrodes and insulation layers in devices. Fabricated junctions have yielded good tunneling characteristics with excellent uniformity and reproducibility. The maximum critical current density was widely changed from 300 A/cm2to 8 kA/cm2. All refractory single flux quantum(SFQ) memory cells in a 32×32 arrangement have been integrated with a 2.5 μm minimum linewidth on a chip using this process, and an SFQ cell in the memory array has been successfully operated. The maximum deviation of critical currents in the memory array was measured to be ±6.5%.

IEEE Transactions on Magnetics•May 1, 1983•60 citations

Fabrication of High Quality NbN/Pb Josephson Junction

Fujitoshi Shinoki, S. Takada, S. Kosaka +1 more

A fabrication technology of NbN/Pb Josephson tunnel junctions has been developed by using a new microfabrication technique. The Josephson characteristics of NbN/Pb tunnel junctions formed on rf reactive sputtered NbN films are reported. The junctions are found to have large gaps (ΔNbN+ΔPb=3.8 mV), low leakage, and to be quite stable with respect to thermal cyclings and storage at room temperature.

International Conference on Solid State Devices and Materials (SSDM)•Aug 28, 1979•0 citations

Fabrication of experimental Josephson tunneling circuits

J. H. Greiner, S. Basavaiah, I. Ames

A multilevel thin-film process has been developed for fabricating experimental circuits containing Josephson tunneling gates, insulated crossings, superconducting contacts, and terminating resistors. The process utilizes a Nb film for the ground plane and Pb alloy films for overlying superconducting layers. Insulation is achieved through the use of vacuum-deposited SiO films and anodization of the Nb ground plane. An oxide formed by rf sputter-etching in an oxygen plasma is used for forming the tunneling barriers. Photoprocessing techniques are used for patterning. Through use of the process it has been possible to fabricate experimental memory and logic circuits which survive thermal cycling to 4.2 K and intervening storage at room temperature without significant changes in electrical characteristics.

Journal of Vacuum Science and Technology•Jan 1, 1974•67 citations
A technique for the fabrication of Josephson tunnel junctions without breaking vacuum and without the use of masks is presented. No chemical processing is done on either of the junction electrode surfaces. Hence, no chemical or reactive cleaning is required before the formation of the tunneling barrier. Nevertheless, standard photolithography and chemical or plasma etching can be employed for defining patterns. I-V characteristics of Nb-NbOx-Pb junctions fabricated by this method have not exhibited a ’’knee’’ at the onset of the quasiparticle current.
A procedure is described for fabricating thin film Nb/Nb oxide/Pb-alloy Josephson tunnel junctions that satisfies the principal requirements for integrated circuit design and fabrication. A deposited Nb film, evaporated from an e-gun heated source, was patterned by chemical etching to form a base electrode. A junction was completed by plasma etching and plasma oxidizing the Nb junction area to form a tunnel barrier and by depositing a Pb alloy counterelectrode. Josephson tunnel junctions with Nb/Nb oxide/Pb-Au-In structures were prepared with low excess subgap currents in the current-voltage (I-V) curve and with reproducible and stable I-V characteristics. Variations in junction current density from run-run were ± 15%. Seven 3-junction interferomeeters out of a population of 50,000 were shorted (99.99% yield) for causes not immediately attributable to photoresist-related defects. No changes in Josephson current were detected after thermal cycling 17,000 interferometers 1,800 × between room temperature and 4.2°K, after storing them for 2 years at 5°C, or after annealing 5,000 interferometers for 4.5 hours at 70°C.
All hard Josephson tunnel junctions, whose base and counter electrodes are composed of double-layered niobium nitride (NbN) and niobium (Nb) films, have been successfully fabricated by isolating a junction sandwich formed on a whole silicon wafer with a reactive ion etching technique. The reactive ion etching technique has been used for patterning both base and counterelectrodes, and self-aligning definition of junction areas has been performed. The fabricated junctions show good quality single-particle tunneling characteristics and excellent uniformity in critical currents.
We have developed a new integration method for Josephson tunnel junctions based on high Tc superconducting compound materials such as NbN. In this method, a sputtered ZnO film has been employed as a resist mask which can be used in high substrate temperatures during the film deposition. It has been found that fine patterns of the refractory superconducting film can be obtained by this method and the patterning processes have no interference with other integration processes. We have applied this method to patterning base electrode of NbN and formed high quality NbN-oxide-Pb Josephson tunnel junctions by using an rf plasma oxidation. The fabricated junctions have been found to have a relatively large gap ( ∼ 4.0 mV ) and low current leak in the subgap region, and to be quite stable for thermal cyclings and storage. We have also fabricated quantum interference memory devices by integrating these junctions and the operation has been successfully demonstrated.
We have developed a novel process for fabricating all refractory Josephson tunnel junctions whose base and counter electrodes are composed of (Nb-NbN) double-layered films. In this process, tunnel junctions have been isolated using a reactive ion etching from a junction sandwich which had been formed on an entire silicon wafer, and also the reactive ion etching has been used for patterning electrodes and insulation layers in devices. Fabricated junctions have yielded good tunneling characteristics with excellent uniformity and reproducibility. The maximum critical current density was widely changed from 300 A/cm2to 8 kA/cm2. All refractory single flux quantum(SFQ) memory cells in a 32×32 arrangement have been integrated with a 2.5 μm minimum linewidth on a chip using this process, and an SFQ cell in the memory array has been successfully operated. The maximum deviation of critical currents in the memory array was measured to be ±6.5%.
A multilevel thin-film process has been developed for fabricating experimental circuits containing Josephson tunneling gates, insulated crossings, superconducting contacts, and terminating resistors. The process utilizes a Nb film for the ground plane and Pb alloy films for overlying superconducting layers. Insulation is achieved through the use of vacuum-deposited SiO films and anodization of the Nb ground plane. An oxide formed by rf sputter-etching in an oxygen plasma is used for forming the tunneling barriers. Photoprocessing techniques are used for patterning. Through use of the process it has been possible to fabricate experimental memory and logic circuits which survive thermal cycling to 4.2 K and intervening storage at room temperature without significant changes in electrical characteristics.